当前位置: X-MOL 学术Geophysics › 论文详情
Our official English website, www.x-mol.net, welcomes your feedback! (Note: you will need to create a separate account there.)
Seismic imaging using an e-vib — A case study analyzing the signal properties of a seismic vibrator driven by electric linear synchronous motors
Geophysics ( IF 3.0 ) Pub Date : 2021-05-10 , DOI: 10.1190/geo2020-0181.1
Bojan Brodic 1 , Paul Ras 2 , Richard de Kunder 3 , Guy Drijkoningen 3, 4 , Alireza Malehmir 1
Affiliation  

Seismic imaging characteristics of a prototype electrically driven, linear synchronous motor-based, vertical-force seismic vibrator (“e-vib”) were evaluated at a site in the Netherlands. The system weighs 1.65 t and excites seismic signals with a peak force of 6.7 kN. Data were recorded along two collocated geophone-based nodal and landstreamer microelectromechanical system - MEMS-based sensor 2D seismic profiles. To obtain a broad bandwidth data set, the e-vib operated with a 1–200 Hz linear sweep. Shot gathers of the merged nodal-landstreamer data set indicated good-quality seismic data of a broadband nature. The processed merged data set demonstrates high-resolution reflections of the stratigraphic members from approximately 200 m to 2 km, with visible reflections as deep as 2.5–2.9 km. As a reference, we also processed a legacy 3D microspread data set acquired at the same site with a magnitude stronger (14.1 t, 67.5 kN) hydraulic vibrator. Comparison of our nodal-landstreamer seismic section versus 2D slices extracted from the processed microspread seismic volume suggested similar signal penetration depth and the same key marker horizons seen in both. Analysis of the reaction mass and base-plate accelerometer signals recorded with the e-vib source operating on grass and on asphalt surfaces indicates that the e-vib has low total harmonic distortion. The results obtained indicate that, although relatively small, the e-vib is capable of generating high-quality broadband seismic data.

中文翻译:

使用e-vib进行地震成像—一个案例分析,该案例分析了由线性同步电动机驱动的地震振动器的信号特性

在荷兰的一个地点评估了原型电动,基于线性同步电动机的垂直力地震振动器(“ e-vib”)的地震成像特性。该系统重1.65吨,并以6.7 kN的峰值力激发地震信号。沿两个并置的基于地震检波器的节点和陆地流微机电系统(基于MEMS的传感器2D地震剖面)记录了数据。为了获得较宽的带宽数据集,电子振动器应以1–200 Hz的线性扫描进行操作。合并的节点-陆流者数据集的镜头集表明了宽带性质的高质量地震数据。处理后的合并数据集显示了地层成员的高分辨率反射,范围约为200 m至2 km,可见反射深度达2.5–2.9 km。作为参考,我们还处理了在同一地点采集的传统3D微扩散数据集,该数据集使用的震级更强(14.1 t,67.5 kN)液压振动器。将我们的节点-陆上拖缆地震剖面与从已处理的微扩展地震体积中提取的2D切片进行的比较表明,两者都具有相似的信号穿透深度和相同的关键标志层。通过在草地和沥青表面上运行的电子振动源对反应质量和底板加速度计信号的分析表明,该电子振动的总谐波失真较低。获得的结果表明,尽管相对较小,但电子振动能够生成高质量的宽带地震数据。将我们的节点-陆上拖缆地震剖面与从已处理的微扩展地震体积中提取的2D切片进行的比较表明,两者都具有相似的信号穿透深度和相同的关键标志层。对使用在草地和沥青表面上运行的电子振动源记录的反应质量和基板加速度计信号进行的分析表明,电子振动具有较低的总谐波失真。获得的结果表明,尽管相对较小,但电子振动能够生成高质量的宽带地震数据。将我们的节点-陆上拖缆地震剖面与从已处理的微扩展地震体积中提取的2D切片进行的比较表明,两者都具有相似的信号穿透深度和相同的关键标志层。对使用在草地和沥青表面上运行的电子振动源记录的反应质量和基板加速度计信号进行的分析表明,电子振动具有较低的总谐波失真。获得的结果表明,尽管相对较小,但电子振动能够生成高质量的宽带地震数据。对使用在草地和沥青表面上运行的电子振动源记录的反应质量和基板加速度计信号进行的分析表明,电子振动具有较低的总谐波失真。获得的结果表明,尽管相对较小,但电子振动能够生成高质量的宽带地震数据。对使用在草地和沥青表面上运行的电子振动源记录的反应质量和基板加速度计信号进行的分析表明,电子振动具有较低的总谐波失真。获得的结果表明,尽管相对较小,但电子振动能够生成高质量的宽带地震数据。
更新日期:2021-05-10
down
wechat
bug