当前位置: X-MOL 学术Mater. Technol. › 论文详情
Our official English website, www.x-mol.net, welcomes your feedback! (Note: you will need to create a separate account there.)
In vitro investigation of the effect of preheating, thermal cycling, and different chewing environment temperatures on the wear of dental composite resins
Materials Technology ( IF 2.9 ) Pub Date : 2021-02-14 , DOI: 10.1080/10667857.2021.1879540
Recep Sadeler 1 , Alidad Saeidi 1 , Sedanur Keleş 1
Affiliation  

ABSTRACT

To determine the effect of different temperature on the wear amounts of dental composite material prepared in Pre-heating Temperature (PTG,60°C) and Room Temperature (RTG,23°C). To increase the Degree of conversion (%DC) in material by pre-heating process, and to investigate the effects of the employed method on the amount of wear. To evaluate the effect of %DC on the material’s surface roughness.To evaluate the effect of thermal cycling on the material’s surface roughness. Valux™ Plus, x-trafil and Charisma® Classic materials were polymerised in two groups: RTG and PTG. The mechanical loadings were applied simultaneously with different In vitro Chewing Environment Temperature (ICET). To perform the thermal cycle (ICET = 5/55°C), 20,000 thermal cycles were applied simultaneously with 500,000 mechanical loading. Amounts of wear, hardness, %DC, and surface roughness were evaluated statistically by ANOVA. Amount of wear rate, and loss of filler particles at the wear zones were changed in different ICET conditions. Pre-heating process caused increase in %DC, surface roughness, and hardness value of all materials. The increase of %DC increased wear resistance in ICET = 5°C, 35°C, and 55°C for x-trafil and Charisma® Classic. Moreover, the same pattern was recorded for the ICET = 5°C for Valux™ Plus material. In Valux™ Plus, x-trafil and Charisma® Classic materials the maximum wear occurred in the RTG group at the ICET = 5°C. Pre-heating and thermal cycling processes caused increase of the surface roughness values. For all materials the pre-heating process caused decrease of wear resistance in the ICET = 5/55°C.



中文翻译:

预热、热循环和不同咀嚼环境温度对牙科复合树脂磨损影响的体外研究

摘要

确定不同温度对在预热温度(PTG,60°C)和室温(RTG,23°C)下制备的牙科复合材料磨损量的影响。通过预热工艺提高材料的转化度(%DC),并研究所采用的方法对磨损量的影响。评估 %DC 对材料表面粗糙度的影响。评估热循环对材料表面粗糙度的影响。Valux™ Plus、x-trafil 和 Charisma® Classic 材料聚合成两组:RTG 和 PTG。机械载荷与不同的体外咀嚼环境温度 (ICET) 同时施加。为了执行热循环 (ICET = 5/55°C),同时应用了 20,000 个热循环和 500,000 个机械负载。磨损量、硬度、%DC、通过 ANOVA 对表面粗糙度进行统计评估。在不同的ICET条件下,磨损率和磨损区填料颗粒的损失发生了变化。预热过程导致所有材料的%DC、表面粗糙度和硬度值增加。x-trafil 和 Charisma® Classic 在 ICET = 5°C、35°C 和 55°C 时,%DC 的增加提高了耐磨性。此外,对于 Valux™ Plus 材料的 ICET = 5°C 记录了相同的模式。在 Valux™ Plus、x-trafil 和 Charisma® Classic 材料中,最大磨损发生在 RTG 组中,ICET = 5°C。预热和热循环过程导致表面粗糙度值的增加。对于所有材料,预热过程导致 ICET = 5/55°C 时的耐磨性降低。在不同的ICET条件下,磨损区填料颗粒的损失和损失发生了变化。预热过程导致所有材料的%DC、表面粗糙度和硬度值增加。x-trafil 和 Charisma® Classic 在 ICET = 5°C、35°C 和 55°C 时,%DC 的增加提高了耐磨性。此外,对于 Valux™ Plus 材料的 ICET = 5°C 记录了相同的模式。在 Valux™ Plus、x-trafil 和 Charisma® Classic 材料中,最大磨损发生在 RTG 组中,ICET = 5°C。预热和热循环过程导致表面粗糙度值的增加。对于所有材料,预热过程导致 ICET = 5/55°C 时的耐磨性降低。在不同的ICET条件下,磨损区填料颗粒的损失和损失发生了变化。预热过程导致所有材料的%DC、表面粗糙度和硬度值增加。x-trafil 和 Charisma® Classic 在 ICET = 5°C、35°C 和 55°C 时,%DC 的增加提高了耐磨性。此外,对于 Valux™ Plus 材料的 ICET = 5°C 记录了相同的模式。在 Valux™ Plus、x-trafil 和 Charisma® Classic 材料中,最大磨损发生在 RTG 组中,ICET = 5°C。预热和热循环过程导致表面粗糙度值的增加。对于所有材料,预热过程导致 ICET = 5/55°C 时的耐磨性降低。和所有材料的硬度值。x-trafil 和 Charisma® Classic 在 ICET = 5°C、35°C 和 55°C 时,%DC 的增加提高了耐磨性。此外,对于 Valux™ Plus 材料的 ICET = 5°C 记录了相同的模式。在 Valux™ Plus、x-trafil 和 Charisma® Classic 材料中,最大磨损发生在 RTG 组中,ICET = 5°C。预热和热循环过程导致表面粗糙度值的增加。对于所有材料,预热过程导致 ICET = 5/55°C 时的耐磨性降低。和所有材料的硬度值。x-trafil 和 Charisma® Classic 在 ICET = 5°C、35°C 和 55°C 时,%DC 的增加提高了耐磨性。此外,对于 Valux™ Plus 材料的 ICET = 5°C 记录了相同的模式。在 Valux™ Plus、x-trafil 和 Charisma® Classic 材料中,最大磨损发生在 RTG 组中,ICET = 5°C。预热和热循环过程导致表面粗糙度值的增加。对于所有材料,预热过程导致 ICET = 5/55°C 时的耐磨性降低。x-trafil 和 Charisma® Classic 材料的最大磨损发生在 RTG 组中,ICET = 5°C。预热和热循环过程导致表面粗糙度值的增加。对于所有材料,预热过程导致 ICET = 5/55°C 时的耐磨性降低。x-trafil 和 Charisma® Classic 材料的最大磨损发生在 RTG 组中,ICET = 5°C。预热和热循环过程导致表面粗糙度值的增加。对于所有材料,预热过程导致 ICET = 5/55°C 时的耐磨性降低。

更新日期:2021-02-14
down
wechat
bug