Skip to main content
SpringerLink
Log in

Effect of Alloying Additions and High Temperature T5-Treatment on the Microstructural Behavior of Al–Si-Based Eutectic and Hypo-Eutectic Alloys

  • Technical Paper
  • Published:
International Journal of Metalcasting Aims and scope Submit manuscript

Abstract

The present study has been undertaken to investigate the effect of alloying additions and high temperature T5-treatment consisting of high temperature direct aging after casting, on the microstructural characteristics of some Al-Si-based eutectic and near-eutectic alloys, typically used in the automotive industry. For comparison purposes and in order to estimate the effect of Mg, three sets of samples consisting of Al-11.9wt%Si (AS13, B413), Al-11.67wt%Si-0.22wt%Mg (AS10G) and Al-7.2wt%Si-0.44wt% Mg (AS7G06, A356) alloys have been first studied in the as-cast state. In order to examine the effect of heat treatments, three groups of alloys were investigated in two different states, namely: (i) after T6-treatment consisting of solutionizing at 540 °C for 10 hours, water quenching and then aging at 160 °C for 4 hours; and (ii) after high temperature T5-treatment consisting of annealing at 300 °C, 450 °C and 500 °C for different aging times in order to locate a possible peak hardness. Microstructural examination was carried out using optical microscopy, scanning electron microscopy, energy Dispersive Spectrometry (EDS), X-Ray Diffraction and Brinell-hardness measurements. Our as-cast alloys’ microstructure revealed that all the different intermetallic phases, such as the Q-Al5Cu2Mg8Si6 phase, the α-Al15(MnFe)3Si2, β-Al5-Fe-Si, π-Al8FeMg3Si6 and Al7Cu2Fe iron-rich compounds, as well as the Al2Cu and Mg2Si hardening precipitates, have been formed during solidification. Besides, X-rays diffraction patterns revealed that while some Al2Cu hardening precipitates have exhibited total dissolution, after solutionizing, the undesirable iron-rich phases have remained at least partially insoluble after the different heat treatments. A semi-quantitative X-Rays diffraction analysis, performed after the different heat treatments, has shed light on the interplay between the Fe-rich intermetallic compounds, denoting the transformation of the π-Al8FeMg3Si6 into the β-Al5FeSi phase on the one hand and between π-Al8FeMg3Si6 and Q-Al5Cu2Mg8Si6 phases in the precipitation and dissolution of Al2Cu and Mg2Si phases on the other hand. Both of the two processes, marking a certain interaction between the different intermetallic compounds, are observed to give rise to a significant release of Mg and Si solute atoms and to enhance the hardening precipitates volume fraction after heat treatments. It turns out that high temperature T5-treatment is more appropriate and even more efficient than the usual T6 one, in the sense that it yields a more significant amount of hardening precipitates giving rise to higher hardness peaks with just one step treatment.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13

Similar content being viewed by others

References

  1. R. Chen, Xu. Qingyan, Z. Jia, B. Liu, Precipitation behavior and hardening effects of Si-containing dispersoids in Al–7Si–Mg alloy during solution treatment. Mater. Des. 90, 1059–1068 (2016)

    Article  CAS  Google Scholar 

  2. L. Ceschini, I. Boromei, A. Morri, S. Seifeddine, I.L. Svensson, Microstructure, tensile and fatigue properties of Al-10%Si-2% Cu alloy with different Fe and Mn content cast under controlled condition. J. Mater. Processing Technol. 209, 5669–5679 (2009)

    Article  CAS  Google Scholar 

  3. Z. Sersour, L. Amirouche, Effect of aging and treatments on the microstructural behavior of some Al-Si based Alloys. Appl. Mech. Mater. 775, 152–159 (2015)

    Article  Google Scholar 

  4. E.A. Elsharkawi, E. Samuel, A.M. Samuel, F.H. Samuel, Effects of Mg, Fe, Be dditions and solution heat treatment on the π-AlMgFeSi iron intermetallic phase in Al–7Si–Mg alloys. J Mater Sci 45, 1528–1539 (2010)

    Article  CAS  Google Scholar 

  5. Q.G. Wang, C.J. Davidson, Solidification and precipitation behavior of Al-Si-Mg casting alloys. J. Mater. Sci 36, 793–750 (2001)

    Google Scholar 

  6. M.F. Ibrahim, A.M. Samuel, H.W. Doty et al., Effect of aging conditions on precipitation hardening in Al–Si–Mg and Al–Si–Cu–Mg Alloys. Inter Metalcast 11, 274–286 (2017). https://doi.org/10.1007/s40962-016-0057-z

    Article  Google Scholar 

  7. Z. Ma, E. Samuel, A.M.A. Mohamed, A.M. Samuel, F.H. Samuel, H.W. Doty, Influence of aging treatments and alloying additives on the hardness of alloys. Mater. Des. 31, 3791–3803 (2010)

    Article  CAS  Google Scholar 

  8. A.M.A. Mohamed, F.H. Samuel, S.A. Kahtani, Microstructure, Tensile properties and fracture behavior of high temperature Al-Si-Mg-Cu cast alloys. Mater. Sci. Eng A 577, 64–72 (2013)

    Article  CAS  Google Scholar 

  9. M. Tash, F.H. Samuel, F. Mucciardi, H.W. Doty, Effect of metallurgical parameters on the hardness and microstructural characterization of as-cast and heat-treated 356 and 319 aluminum alloys. Mater. Sci. Eng. A 443, 185–201 (2007)

    Article  Google Scholar 

  10. Q. Li, Y. Zhu, S. Zhao, Y. Lan, D. Liu, G. Jian, Q. Zhang, H. Zhou, Influence of Fe, Mn and Y addition on microstructure and mechanical properties of hypoeutectic A1-7%Si alloy. Intrermetallics. 120, 106768 (2020)

    Article  CAS  Google Scholar 

  11. W. Reif, S. Yu, J. Dutkewicz, R. Ciach, J. Krol, Pre-ageing of AlSiCuMg in relation to structure and mechanical properties. Mater. Des. 18, 253–256 (1997)

    Article  CAS  Google Scholar 

  12. S.G. Shabestari, The effect of iron and manganese on the formation of intermetallic compound in aluminum-Silicon alloys. Mater. Sci. Eng. A 383, 289–298 (2004)

    Article  Google Scholar 

  13. L. Lu, A.K. Dahle, Iron –Rich intermetallic phases and their role in casting defect formation in hypoeutectic Al-Si alloys. Metall. Mater. Transact A 36, 819–835 (2005)

    Google Scholar 

  14. C.M. Dinnis, J.A. Taylor, A.K. Dahle, As-cast morphology of iron -intermetallics in Al-Si foundry alloys. Scr Materialia 53, 955–958 (2005)

    Article  CAS  Google Scholar 

  15. A.M. Samuel, H.W. Doty, S. Valtierra, F.H. Samuel, Relationship between tensile and impact properties in Al-Si-Cu-Mg cast alloys and their fracture mechanisms. Mater. Des. 53, 938–946 (2014)

    Article  CAS  Google Scholar 

  16. A.M. Samuel, E.M. Elgallad, H.W. Doty, S. Valtierra, F.H. Samuel, Effect of metallurgical parameters on the microstructure, hardness impact properties, and fractography of Al-(6.5–11.5) Al wt% Si based alloys. Mater. Des. 107, 426–439 (2016)

    Article  CAS  Google Scholar 

  17. M.H. Abdelaziz, A.M. Samuel, H.W. Doty, S. Valtierra, F.H. Samuel, Effect of alloying additions on the microstructure and tensile properties of Al-Si alloys. J. Mater. Res. Technol. 8(2), 2255–2268 (2019)

    Article  CAS  Google Scholar 

  18. F.H. Samuel, A.M. Samuel, H. Liu, Effect of magnesium content on the ageing behavior of water-chilled Al-Si-Cu-Mg-Fe-Mn (380) alloy castings. J. Mater. Sci. 30, 2531–2540 (1995)

    Article  CAS  Google Scholar 

  19. F.H. Samuel, Incipient melting of Al5Mg8Si6Cu2 and Al2Cu intermetallics in unmodified and strontium—modified Al-Si-Cu-Mg (319) alloys during solution heat treatment. J. Mater. Sci. 33, 2283–2297 (1998)

    Article  CAS  Google Scholar 

  20. M.F. Ibrahim, E. Samuel, A.M. Samuel, A.M.A. Al-Ahmari, F.H. Samuel, Metallurgical parameters controlling the microstructure and hardness of Al-Si-Cu-Mg base alloys. Mater. Des. 32, 2130–2142 (2011)

    Article  CAS  Google Scholar 

  21. Y. Wang, H. Liao, Y. Wu, J. Yang, Effect of Si content on the microstructure and mechanical properties of Al-Si-Mg alloys. Mater. Des. 53, 634–638 (2014)

    Article  CAS  Google Scholar 

  22. M.A. Moustafa, F.H. Samuel, H.W. Doty, Effect of solution heat treatment and additives on the hardness, tensile properties and fracture behavior of Al-Si (A413.1) automotive alloys. J. Mater. Science. 38, 4523–4534 (2003)

    Article  CAS  Google Scholar 

  23. E. Lee, B. Mishra, Effect of cooling rate on the mechanical properties of AA365 aluminum alloy heat-treated under T4, T5, and T6 conditions. Inter. Metalcast. 12, 449–456 (2018)

    Article  Google Scholar 

  24. J. Major, M. Hartlieb, Advances in aluminum foundry alloys for permanent and semi-permanent mold casting. Inter. Metalcasting. 3, 43–53 (2009)

    Article  CAS  Google Scholar 

  25. M. Yıldırım, D. Özyürek, The effects of Mg amount on the microstructure and mechanical properties of Al–Si–Mg alloys. Mater. Des. 51, 767–774 (2013)

    Article  Google Scholar 

  26. A.M.A. Mohamed, A.M. Samuel, F.H. Samuel, H.W. Doty, Influence of additives on the microstructure and tensile properties of near-eutectic Si cast alloy. Mater. Des. 30, 3943–3957 (2009)

    Article  CAS  Google Scholar 

  27. J.F. Major, L. Purdon, T5 aging response of A356/357 hypoeutectic Al-Si foundry alloys under conditions of varying quench rate from the mould. AFS Trans. 112, 461–471 (2004)

    Google Scholar 

  28. S.W. Youn, C.G. Kang, Characterisation of age –hardening behavior of eutectic region in squeeze-cast alloy using nanoindenter and atomic force microscope. Mater. Sci. Eng. A. 425, 28–35 (2006)

    Article  Google Scholar 

  29. K. Yamamoto, M. Takahashi, Y. Kamikubo, Y. Sugiura, S. Iwasawa, T. Nakata, S. Kamado, Influence of process condition on microstructure and mechanical properties of T5-treated 357 aluminum alloys. J. Alloy. Compd. 834, 155133 (2020)

    Article  CAS  Google Scholar 

  30. High Score software, Philips analytical, (2002)

  31. HighScore plus software, Philips analytical, (2010)

  32. www.foseco.fr

  33. JCPDS card N°42-1206

  34. JCPDS card N°02-1309

  35. JCPDS card N° 01-1180

  36. JCPDS card N° 26-1481

  37. JCPDS card N° 04-0836

  38. JCPDS card N° 37-1449

  39. JCPDS card N° 26-0042

  40. Y.C. Tzeng, V.S. Chengn, J.K. Nieh, H.Y. Bor, S.L. Lee, Microstructure and thermal stability of A357 alloy with and without the addition of Zr. J Mater. Eng. Perform. 26, 5511–5518 (2017)

    Article  CAS  Google Scholar 

  41. Z. Ma, E. Samuel, A.M.A. Mohamed, A.M. Samuel, F.H. Samuel, H.W. Doty, Parameters controlling the microstructure of Al-11Si-2.5Cu–Mg alloys. Mater. Des. 31, 902–912 (2010)

    Article  CAS  Google Scholar 

  42. M. Matejka, D. Bolibruchova, Effect of remelting on microstructure of the AlSi9Cu3 alloy with higher iron content. Arch. Foundry Eng. 18(4), 19–24 (2018)

    Google Scholar 

  43. JCPDS card N° 34-0458

  44. JCPDS card N°25-1085

  45. JCPDS card N°01-1148

  46. JCPDS card N° 33-0854

  47. JCPDS card N° 41-0999

  48. S. Beroual, Z. Boumerzoug, P. Paillard, Y. Borjon-Piron, Effects of heat treatment and addition of small amounts of Cu and Mg on the microstructure and mechanical properties of Al-Si-Cu and Al-Si-Mg cast alloys. J. Alloy. Compd. 784, 1026–1035 (2019)

    Article  CAS  Google Scholar 

  49. X. Wu, H. Zhang, Z. Ma, T. Tao, J. Gui, W. Song, B. Yang, H. Zhang, Interactions between Fe-rich intermetallics and Mg-Si phase in Al-7Si XMg alloys. J. Alloy Compd. 786, 205–2014 (2019)

    Article  CAS  Google Scholar 

  50. JCPDS card N° 25-0511

  51. A.M.A. Mohamed, F.H. Samuel, S. Al kahtani, Influence of Mg and solution heat treatment on the occurrence of incipient melting in cast alloys. Mater. Sci. Eng. A. 543, 22–34 (2012)

    Article  CAS  Google Scholar 

  52. Y. Han, A.M. Samuel, H.W. Doty, S. Valtierra, F.H. Samuel, Optimizing the tensile properties of Al–Si–Cu–Mg 319-type alloys: Role of solution heat treatment. Mater. Des. 58, 426–438 (2014)

    Article  CAS  Google Scholar 

  53. S. Shivkumar, C. Keller, D. Apelian, Aging behavior in cast Al-SI-Mg alloys. AFS Trans. 98, 905–911 (1990)

    CAS  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Unit UR-MPE, UMBB, 35000, Boumerdes, Algeria

    Zakia Sersour

  2. Labo.de physique théorique, Faculté de physique, USTHB, BP32, El Alia, 16311, Bab-Ezzouar, Algiers, Algeria

    Lynda Amirouche

Authors
  1. Zakia Sersour
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Lynda Amirouche
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Lynda Amirouche.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Sersour, Z., Amirouche, L. Effect of Alloying Additions and High Temperature T5-Treatment on the Microstructural Behavior of Al–Si-Based Eutectic and Hypo-Eutectic Alloys. Inter Metalcast 16, 1276–1291 (2022). https://doi.org/10.1007/s40962-021-00676-7

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s40962-021-00676-7

Keywords

Search

Navigation