Abstract

Objective. Analyzing and comparing the fit and accuracy of removable partial denture (RPDs) frameworks fabricated with CAD/CAM and rapid prototyping methods with conventional techniques. Materials and Methods. The present systematic review was carried out according to PRISMA guidelines. The search was carried out on PubMed/MEDLINE, Cochrane collaboration, Science direct, and Scopus scientific engines using selected MeSH keywords. The articles fulfilling the predefined selection criteria based on the fit and accuracy of removable partial denture (RPD) frameworks constructed from digital workflow (CAD/CAM; rapid prototyping) and conventional techniques were included. Results. Nine full-text articles comprising 6 in vitro and 3 in vivo studies were included in this review. The digital RPDs were fabricated in all articles by CAD/CAM selective laser sintering and selective laser melting techniques. The articles that have used CAD/CAM and rapid prototyping technique demonstrated better fit and accuracy as compared to the RPDs fabricated through conventional techniques. The least gaps between the framework and cast () were found in RPDs constructed through digital CAD/CAM systems. Conclusion. A better accuracy was achieved using CAD/CAM and rapid prototyping techniques. The RPD frameworks fabricated by CAD/CAM and rapid prototyping techniques had clinically acceptable fit, superior precision, and better accuracy than conventionally fabricated RPD frameworks.

1. Introduction

The accurate fit of removable partial denture (RPD) is a key component of the removable prosthodontics. Conventionally fabricated RPD can be time consuming, and their misfit has been identified as one of the chief complaints of RPD wearers. Thus, various other methods are developed and employed for the fabrication of RPDs, which are less extensive, and work effortlessly with better fit and accuracy [1]. In recent years, innovative technology such as computer-aided designing and computer-aided manufacturing (CAD/CAM) and rapid prototyping (RP) techniques has revolutionized the specialty of prosthodontics, with its use not only in removable dentures but also as extensively as for maxillofacial/craniofacial prostheses [2]. The CAD/CAM-fabricated prostheses, restorations, and devices are utilized in almost all branches of dentistry such as restorative (inlays; onlays), orthodontics (invisible aligners), and prosthetic dental sciences (ceramic veneers; single/multiple crowns; fixed partial dentures; removable complete/partial prostheses) [2, 3].

The RP have also been used to fabricate RPDs and are believed to improve the quality of fit in RPD frameworks [3]. RP constructs RPDs automatically and quickly with high accuracy making them more comfortable and acceptable to the patients. The CAD/CAM uses subtractive manufacturing such as milling techniques while RP utilizes additive manufacturing like three-dimensional (3D) printing, selective laser sintering (SLS), selective laser melting (SLM), and selective laser stereolithography (SLA) [4]. The components manufactured for RPDs must satisfy the functional and biomechanical needs such as retention, stability, support, reciprocation, encirclement, and passivity [5]. The biomechanical needs of the RPDs should accommodate the movements of prosthesis during function without exerting compulsive stresses on the abutment teeth, rigidity of the major connectors, with occlusal rests directing the occlusal forces along the long axis of the teeth and guide planes for enhancing stability [3, 6].

The 3D printing technique has opened a new method of construction of RPD which has clinically presented better accuracy and fit. It is widely being used because of its time effectiveness for the construction of prostheses. It also provides a clean workplace for the technician, not having to deal with plaster or dust [6]. In recent times, digital scans have also been introduced in dentistry and have been shown to have better trueness than the conventional impressions [7]. Digital scans have prevented the need for placing impression material in the mouth, which causes gag reflex and claustrophobia in a great number of patients. This highly advanced technology is acceptable for patients who avoid the use of conventional impressions [7]. Most commonly used material to manufacture RPDs with SLM is cobalt-chromium alloy (Co-Cr). The Co-Cr is commonly used due to its physical properties fulfilling the requirements of RPDs including accurate fit, excellent mechanical properties, easy to clean, and does not intrude with tongue space [8].

Both methods of manufacturing, i.e., conventional and digital, yields satisfactory results, but the digital method of construction of RPDs is less time consuming, with simplified technique and minimal chances of laboratory or clinical errors and better accuracy and fit [5, 9]. Minimum chair side time is needed to evaluate the fit of digitally manufactured RPDs. Trials have been conducted on patients to check the fitting of the dentures fabricated by CAD/CAM and RP techniques [10], and the results are encouraging with regard to patient’s satisfaction and optimal biomechanical performance. Hence, this newest technology of fabrication of RPDs is broadly accepted and used all over the globe. The aim of the present systematic review was to analyze the available literature pertaining to the experimental fit accuracy of digitally designed and fabricated RPDs versus conventionally fabricated RPDs.

2. Materials and Methods

2.1. Research Question

In this systematic review, we followed preferred reporting items for systematic review and meta-analysis (PRISMA) guidelines and Participants Intervention Control Outcomes (PICO) protocol. The focused question was “Does digitally fabricated (CAD/CAM and RP) RPDs frameworks (connectors, retainer, reciprocal components, and denture base) have better fit and accuracy compared to the conventional RPDs?”

2.2. Search Strategy

In this systematic review, PubMed/MEDLINE, Cochrane collaboration, Science direct, and Scopus databases were searched for abstracts and full-text articles available online in July 2020 with no language restrictions. The included articles were searched on the basis of population or patients, including intervention, comparison, and outcome of study. The search was primarily focused on MeSH keywords: Denture, Partial, Removable, Dental Prosthesis, Denture Design, Denture framework, Removable partial denture framework, Removable partial denture designing, Printing, 3D and RPD, 3D printing and RPD, CAD/CAM and RPD, SLS and RPD printing, and SLM and RPD printing. The search was further expanded through scrutiny of references from included articles. Three investigators thoroughly obtained all relevant data and analyzed the results. Any disagreement between the investigators was resolved by consensus and discussion. All included articles assessed the accuracy of fit, retention, and stability of RPDs made with both conventional and digital techniques. After analyzing the data, the final full-text articles were selected, and any repeated studies were removed after reading the titles and abstracts.

2.3. Eligibility Criteria for Literature Search

Inclusion criteria are as follows: clinical trial studies involving comparison between accuracy and fit of RPD frameworks fabricated by conventional and digital techniques, published in English, with both in vitro and in vivo study designs; studies conducted with minimum of 04 dental casts were included; and studies with use of 3D dental cast scanners and 3D printing machines and milling techniques. Studies included analysis of RPD components in terms of fit and accuracy. Lastly, articles with both direct and indirect cast scanning methods were included.

The last search was performed in September 2020. In the 09 articles that were included, the casts or impressions were produced with intraoral scanners, CAD printing, and digital surveys. Fabrication of RPDs was performed using CAD/CAM software, SLS, SLM, SLA, indirect RP, and direct RP. The frameworks were fabricated by cobalt chromium alloys. Every included article was assessed, and the data were extracted based on the following parameters: authors name, study design, assessment methods, follow-up period, study groups, sample size, mean and STD, relevant features of study, and outcome, by three investigators (N.A, S.H and M.S.Z).

Exclusion criteria are as follows: studies that were literature reviews, clinical reports, surveys, or systematic reviews; studies including fixed prosthesis rather than removable partial dentures; studies not including comparisons between digital and conventional techniques; studies missing either one of the two techniques, i.e., conventional or digital; studies that did not focus on the fit of the denture; studies with incomplete information were excluded in this review.

2.4. Quality Assessment of Selected Studies

Furthermore, the quality assessment was assessed according to the parameters described in the Cochrane handbook for systematic reviews of interventions (v5.1.0) [11]. The same 3 review authors autonomously sort out the search to amplify the number of studies recovered. The reviewers surveyed every selected article for the predefined consideration criteria and directed impartial appraisals, and any ambiguity was settled by discussion and agreement or by consultation with a 4th reviewer (N.A). The Newcastle-Ottawa quality assessment scale (NOS) [12] was used for further analysis of the specific included articles.

3. Results

3.1. Results of Literature Search

The combined search identified 518 studies; out of which, 476 duplicate studies were removed, leaving 42 references for further evaluation. Irrelevant abstracts and titles were removed, and 20 full-text articles were assessed for eligibility. Nine studies [1321] representing the relevant findings were included in the systematic review. The PRISMA flow diagram adopted in this systematic review is shown in Figure 1. Eleven full-text articles [13, 2232] were excluded on the basis of lacking a comparability between digital and conventionally fabricated RPDs, review articles, cross-sectional study, and clinical reports (Table 1).

3.2. General Characteristics of Included Studies

All studies included were clinical trials, 04 in vivo trials [13, 14, 16, 19] and 5 in vitro trials [15, 17, 18, 20, 21]. One of the studies assessed the ease of cleaning, ability to speak, comfort, esthetics, stability, and ability to masticate [14]. Similarly, the retention of RPD framework constructed with traditional and digital workflow was compared in one study [16]. Seven studies evaluated the fit accuracy and analyzed the gap between denture framework and master cast, or tissue surfaces [13, 15, 1721]. The number of study casts to analyze the fit and accuracy of RPD frameworks within the included studies ranged from 1 to 20. The follow-up period in the included studies varied from 1 to 6 months. Three of the studies contemplated the rest surfaces [15, 17, 18]. Cobalt chromium alloy was used in majority of studies to fabricate digital and conventional denture frameworks covered with acrylic resins. Polyetheretherketone (PEEK) was used in two articles to construct RPD frameworks. The general characteristic of included studies is summarized in Table 2.

3.3. Digital Method of Fabrication in Included Studies

Digital methods of fabrication of RPDs were used in these studies [1321], each with a different type of CAD/CAM system. In one study [14], sintering laser technology was used to construct RPDs. SLM technique was applied in 5 studies [13, 15, 17, 19, 20] which proved to have a better fit accuracy than conventional lost wax technique; furthermore, for impression, making 1 study [19] partially used direct intraoral scan and CAD for fabricating RPDs, whereas indirect cast scanning with CAD was performed in all included research articles [1321].

3.4. General Outcomes of Included Studies

The majority of the studies [1420] concluded that RPDs constructed via digital workflow had a better fit, accuracy, and satisfaction of patients. Nevertheless, 2 studies [18, 20] found conventional RPD frameworks to be superior in terms of fit and accuracy in long-span RPDs (Table 3). The least clinical gap between RPD framework and tissue surface or cast was observed in CAD/CAM technique . The fit discrepancy was in RPDs constructed with RP (SLM and SLS) 3D printing. The RPD framework fabricated with conventional methods showed a higher mean framework fit discrepancy . The fit and accuracy comparison of RPD frameworks fabricated with digital and conventional methods is presented in Table 4.

3.5. Results of Quality Assessment

Out of the 9 articles included, the randomization in subjects was performed in 4 articles [13, 14, 16, 19]. In 3 studies [13, 14, 19], blinding was carried out. One study [14] mentioned dropout rate of participants. The variables were measured several times in 7 of the included studies [1319]. Sample size calculation was mentioned in 8 articles [1319, 21]. Inclusion criteria were clearly mentioned in 4 studies [13, 14, 18, 20]. Furthermore, examiner reliability was tested in 5 of the studies [13, 15, 1820]. The expected outcomes were prespecified in all included studies [1321]. The results of quality assessment are stated in Table 5. Four studies [15, 16, 18, 20] fall in moderate bias category while 3 studies [13, 14, 19] had low risk of biasness, whereas 2 studies [17, 21] showed a high risk of biasness. In addition, “the quality assessment of selected studies on Newcastle-Ottawa quality assessment scale NOS [12] was ranging from 3 to 7 points.” Five studies [14, 1619] were found to have a moderate risk of biasness. Four of the studies [13, 15, 20, 21] fall in high risk category. A mean score of 7.12 was achieved for the included studies (as mentioned in Table 6).

4. Discussion

In recent years, digital techniques such as CAD/CAM and RP systems have been used to fabricate RPDs. The digital technology offers many advantages, including precise planning of the denture frame components, reduced fabrication time, and improved functional and esthetic results, and improved quality of fit in RPD frameworks [26, 27]. Therefore, this systematic review was conducted to analyze and compare the fit accuracy of digital and conventionally fabricated frameworks/assemblies of RPDs. In this review, both in vitro and in vivo clinical trials were incorporated to get substantial evidence. The included studies used different types of digital techniques, materials, and assessment methods. In literature, one of the most reported manufacturing processes is CAD/CAM milling. However, RP is also gaining prominence recently specially with the introduction of newer techniques such as SLA, SLM, SLS, selective deposition modeling (SDM), fused deposition molding (FDM), and direct inkjet printing (DIP) [21]. Various studies showed promising results when the fit of RPDs fabricated with RP techniques were evaluated [14, 17, 20, 23]. However, in an in vitro study by Arnold et al. [17], RPDs fabricated with RP techniques showed distinct fitting irregularities, while RPDs fabricated with a milling technique showed significantly better framework fit as compared to the traditional ones. In majority of the studies, RPDs constructed via digital method had better accuracy of fit [13, 15, 19, 20] although no study discussed the long-term clinical performance. Furthermore, various methods have been reported in the literature to evaluate the fit and accuracy of RPD frameworks, including visual inspection, pressing test, color mapping, and indirect measurements of the gap filled with an impression material [9, 13, 22, 31].

Seven of the included studies [13, 15, 1721] evaluated the fit accuracy of RPD frameworks. Soltanzadeh et al. [18] revealed that the conventionally fabricated RPD frameworks had a better fit accuracy compared to the 3D-printed frameworks; color mapping was carried out through comprehensive metrology software as an assessment tool. Similarly, Chen et al. [20] reported that conventional RPD frameworks showed better outcome in long span partially edentulous arches. However, a clinical gap of up to <0.2 mm can be achieved in short-span RPD frameworks fabricated with SLM methods. The remaining 5 studies revealed that the digitally fabricated RPD frameworks were more accurate than conventional ones. The studies used different assessment and fabrication methods.

In a study by Tregerman et al. [19], the framework was fabricated from a Co-Cr alloy by SLM. The evaluation consisted of scoring a survey with seven framework-related parameters and was completed by five clinicians, concluding that the sole digital method of fabrication was found to be the best [19]. Almufleh et al. [14] compared patient’s satisfaction of RPDs fabricated by conventional and laser-sintering technology. More satisfaction was observed with the prosthesis fabricated with SLS technique. They reported that SLS-based RPD was more efficient, retentive, stable, and comfortable, and it improved their mastication and speech. This significant difference could be related to the enhanced mechanical properties of laser-sintered alloys, which are harder, denser, and proved a better microstructural organization with higher yield strength and ultimate tensile strength than cast cobalt chromium alloys, although the study had a small sample size and short follow-up that could limit the generalizability to long-term clinical performance.

In another clinical study by Maryod et al. [16], retention of digitally processed RPDs and conventional RPDs was evaluated. The results showed that the digitally processed RPDs were more retentive as it was associated with less human intervention. Mohamed et al. [23] carried out the clinical and cytological evaluation of RPDs fabricated by SLS additive prototyping technique and found a favorable oral environment along with an accurate fit and adaptation. Cytologically, at the microscopic level, no inflammatory cells were traced in the normally desquamated oral epithelial cells.

Although the result of the included studies was favorable for milling and 3D printing RPD frameworks, there were certain limitations to our study. For instance, most of the studies [13, 15, 1720] did not contain a follow-up period. Except in a study by Almufleh et al. [14], a follow-up period was four weeks, and Waleed et al. evaluated the prosthesis after three months [16]. However, most of the studies were in vitro studies [15, 1720], and the results were not correlated with in vivo investigations. Therefore, it was not clear that the digital RPDs fabricated in these studies are suitable for clinical application or not. Furthermore, in this review, three studies were lacking blindness [1517]. Though one of the studies showed that the digitally fabricated RPDs had short term accuracy [14], similarly, Pooya et al. found that conventionally fabricated dentures had a better fit compared to digital RPDs [18]. To explore these shortcomings and improve the scientific evidence, we recommend further studies should be carried out with a larger sample size and more importantly with long-term follow-up periods and clinical correlation to predict the actual outcome and fit accuracy of conventional and digitally fabricated RPDs.

5. Conclusions

The results of this review described that the fit accuracy of removable partial denture frameworks fabricated by digital (CAD/CAM and RP) techniques is superior as compared to the frameworks fabricated by conventional techniques. According to the included studies in this review, the CAD/CAM and rapid prototyping RPD frameworks showed clinically acceptable gaps and fit accuracy in comparison to RPD constructed with conventional techniques. However, CAD/CAM and rapid prototyping techniques are increasing the scope of digital dentistry but are still under development. Further studies are required to assess their accuracy with clinical performance in removable prosthodontics.

Data Availability

The raw data used to support the findings of this study are included within the article.

Conflicts of Interest

The authors declare no conflict of interest.

Authors’ Contributions

N.A, M.S.A, and S.H planned and designed the present work, and N.A (Nimra Ahmed) and S.A was responsible for realizing the work. N.A, M.S.A, and M.S.Z were responsible for the data acquisition and analysis. N.A (Nimra Ahmed), S.R.H, S.A, S.H, and M.K.A drafted and revised the manuscript. NA, MKA, M.S.Z, and S.R.H approved the final version of the manuscript. All authors read and approved the final manuscript. N.A and MKA contributed equally to this work and are corresponding authors.

Acknowledgments

The authors thank the University Sains Malaysia, King Saud University, and Jouf University, Kingdom of Saudi Arabia, and also, Altamash Institute of Dental Medicine, Pakistan, for the support and facilitation in this study.