Skip to main content
Log in

Estimating Loading Capacity in Fit-Pressed Adhesive Joints

  • Published:
Polymer Science, Series D Aims and scope Submit manuscript

Abstract

The results of experimental studying glue-mechanical shaft–sleeve joints using anaerobic sealants are presented. Quantitative estimates of the quality of the surface layers are obtained for mating parts, which allows assessing the values of the waviness of shaft and sleeve surfaces. A technique for determining the waviness of cylindrical joints is described. The effect of the press fit on mechanical strength of the shaft–sleeve joint is established depending on the properties of an anaerobic sealant.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.

Similar content being viewed by others

REFERENCES

  1. D. A. Aronovich, “Modification of the properties of anaerobic adhesives. Review of current advances,” Plast. Massy., Nos. 7–8, 9–15 (2019).

  2. D. A. Aronovich, A. F. Mupokh, A. P. Sineokov, and Z. S. Khamidulova, “Investigation of the properties of anaerobic-curing adhesives in cylindrical joints,” Klei, Germetiki, Tekhnol., No. 6, 2–6 (2008).

  3. V. A. Zorin, N. I. Baurova, and A. M. Shakurova, “Investigation of the structure of an encapsulated anaerobic adhesive,” Polym. Sci., Ser. D 7 (4), 303–305 (2014).

    CAS  Google Scholar 

  4. I. I. Voyachek, “Selective hardening of pressure coupled joints in assembly with anaerobic materials,” Izv. Vyssh. Uchebn. Zaved., Povolzh. Reg., No. 2, 192–204 (2015).

  5. D. V. Knyazev, “Features of the assembly of cylindrical joints with pressure coupling by the combined heat-glue method,” Izv. Mosk. Gos. Tekh. Univ. MAMI, No. 2, 270–274 (2008).

    Google Scholar 

  6. A. P. Petrova and G. V. Malysheva, Adhesives, Adhesive Binders, and Adhesive Prepregs: Handbook, Ed. by E. N. Kablov (VIAM, Moscow, 2017) [in Russian].

    Google Scholar 

  7. G. V. Malysheva and O. A. Ryakhovskii, “Calculation of force and tightening torque of threaded joints assembled using anaerobic material,” Polym. Sci., Ser. D 7 (4), 306–309 (2014).

    CAS  Google Scholar 

  8. O. A. Ryakhovskii, “A new method of sealing the joint of flanges of housings at high internal pressure,” Izv. Vyssh. Uchebn. Zaved., No. 5, 29–33 (2013).

  9. E. V. Ryzhov, Fundamentals of Calculating the Butt Surfaces of Machine Parts for Contact Stiffness (Mashgiz, Moscow, 1962) [in Russian].

    Google Scholar 

  10. A. V. Borodin and I. L. Ryazantseva, “Effect of modification of mating surfaces on the load-bearing capacity of preloaded joints,” Izv. Transsiba, No. 1, 15–20 (2010).

    Google Scholar 

  11. N. V. Bodrykh and G. V. Malysheva, “Repair of starter storage batteries,” Polym. Sci., Ser. D 3 (1), 70–73 (2010).

    Google Scholar 

Download references

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to G. V. Malysheva.

Additional information

Translated by V. Vetrov

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Lyubchenko, M.A., Ryakhovskii, O.A., Vorob’ev, A.N. et al. Estimating Loading Capacity in Fit-Pressed Adhesive Joints. Polym. Sci. Ser. D 14, 345–349 (2021). https://doi.org/10.1134/S1995421221030199

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1134/S1995421221030199

Keywords:

Navigation