Abstract
Pasty rocket engines have broad application prospects in the aerospace field. To study the internal ballistic characteristics of the pasty propellant rocket engine, the burning surface change model of pasty propellant was built. The calculation program was developed to calculate the pressure evolution in the combustion chamber, and the experiment was carried out based on a pasty propellant rocket test system. The data calculated by the program are in good agreement with the experiment, the error of the initial pressure peak is only 4.02%, and the internal ballistic characteristics of the rocket engine at each stage were analyzed detailly. The effects of ignition delay time, transport pipeline structure, free volume of the combustion chamber, mass flow rate, and flow velocity of the pasty propellant on internal ballistic characteristics of the pasty propellant rocket engine are investigated. The results indicate that when the ignition delay time increases, the pressure rises faster and the initial pressure peak increases obviously. The transport pipe diameter changes from 11.3 mm to 7.4 mm, and the initial combustion time and residual propellant combustion time decreased by 41.3% and 36.0%. The reduction of the free volume of the combustion chamber can reduce the initial pressure peak and the time to reach the equilibrium pressure. The initial pressure spike and equilibrium pressure rise with the increase of the pasty propellant flow velocity. While the ignition transient decreased with the increase of the pasty propellant flow velocity. The internal ballistic properties can be improved by reducing the ignition delay time, the diameter of the transport pipeline, and the free volume of the combustion chamber, or by increasing the mass flow rate of the pasty propellant rocket engine.
1. Introduction
The pasty propellant is a kind of fuel that has not been solidified completely and presents non-Newtonian fluid behavior with high viscosity and plasticity, which is considered to be one of the advanced chemical propulsion in the 21st century [1]. The pasty rocket engine is a reliable thrust regulation propulsion system that has many advantages, which can be used in both civilian and military applications. It has simplified construction with deeper thrust regulation and high safety in comparison with liquid rocket engines. Compared with the traditional solid rocket motor, the pasty rocket engines have advantages of repeatable start and large thrust adjustable range [2]. In the military field, pasty rocket engines can be used for attitude engines and terminal guidance correction engines for strategic missile warhead guidance, as well as kinetic energy weapon warhead engines [3]. In the aerospace field, pasty rocket engines can be used as the internal gas servo system of the rocket and the orbit-changing attitude engine of the satellite [4–6].
The pasty rocket engine operation process has been extensively investigated for decades with theoretical, numerical, and experimental studies. Kukushkin and Ivanchenko [5, 6] have achieved certain results in the theory of pasty rocket engine, rheological properties, and practical application of pasty propellant. Several types of experimental rocket engines have been designed, manufactured, and tested successfully. Song and Ye [7] proposed a theoretical model and a test engine of the pasty rocket engine, and the residual heat of the combustion chamber was used to achieve multiple pulses. Numerical simulation results showed that this method can achieve multiple ignitions of the engine. Zhang et al. [8] numerically studied the pressure drop and heat transfer of the pasty propellant flowing in the pipeline based on two-phase flow theory. The influences of the pipe diameter and inlet velocity on the pressure drop were analyzed. Luo et al. [9] numerically simulate the working process of the solid-gelled propellant gas generator the discrete ordinates radiation model. Liu [10] designed a pasty propellant gas generator to study the start-up characteristics of the flow adjustable pasty gas generator based on gas pressure driven. In addition, many researchers have conducted a lot of studies on the atomization characteristics of gel propellant or slurry fuel through experiments, analysis, and numerical simulation. Natan and Rahimi [11] reviewed the advantages, rheological properties, and combustion behavior of the gel propellants. Douglas and Rober [12] developed a method for formulating and characterizing the properties of metalized gel propellants for the propulsion systems. Hodge et al. [13] outlined the applications, capabilities, and state-of-the-art gelled propulsion systems, and the reliability of the gel engine system was verified through actual flight tests. Turns and Mueller [14, 15] analytically and experimentally examined the secondary atomization, ignition characteristics, and combustion performance of aluminum/liquid hydrocarbon slurry propellants. The effect of solid particle content and maximum size of particle on the smallest droplet diameter that allows secondary atomization were analyzed by using applying the established droplet shell-forming model. Bondarenko et al. [16] have investigated the thermal and gas dynamics processes in the combustion chamber of prospective rocket engines using slurry fuel, and experimental and numerical results of pressure and temperature in the combustion chamber were presented. Rahimi et al. [17] formulated and characterized a type of gel propellant, and a laboratory-scale rocket engine with selected hypergolic neat-liquid and gelled bipropellant combinations was examined successfully. Cao et al. [18–20] experimentally investigated the combustion characteristics of gelled fuel formed by inorganic gallant. The results show that the combustion rate of inorganic gel fuel decreases with the increase of gellant content, and the flow characteristic research of gelled fuel was conducted numerically. However, to the best of our knowledge, the internal ballistics of pasty propellant rocket engines has not been fully investigated yet in the open literature.
In the pasty propellant rocket engine, the internal ballistics covers the time from the onset of the igniter until the pasty propellant consumes completely. During the past decades, a lot of studies have been conducted on the numerical simulations and burning surface model of the solid rocket motor internal ballistics. Yilmaz et al. [21, 22] developed a numerical approach coupled to strand burner pressure-time history to determine the burning rates of different solid propellants, and the vacuum specific impulse, density vacuum specific impulse, and solid exhaust products were examined for several propellant formulations based on the pyrophoric material triethylaluminum (TEA) using CEA thermodynamics code. Tahsini et al. [23] numerically investigated the effect of viscosity on the internal ballistics simulation of a solid rocket motor with an internal burning cylindrical grain. Greatrix [24] studied the effect of negative/positive erosive burning on the profile of a cylindrical-grain motor numerically. Willcox et al. [25, 26] developed a new minimum distance function method to describe the 3-D burning surface geometry of the propellant grain, and internal ballistics simulations of solid rocket motors were conducted by using a one-dimensional, time-dependent single-phase compressible flow equation. Tola and Nikbay [27, 28] developed an in-house code such as a zero-dimensional internal ballistic solver and an analytical burnback solver which are implemented to compute the variation of chamber pressure and the rocket thrust transiently. Fei et al. [29] proposed a new combustion surface calculation algorithm by tracking the depression of the combustion surface of the grain to realize the combustion surface change law of arbitrary configuration of grains. In terms of propellant combustion, Yilmaz et al. [30–32] recently used CFD codes to take advantage of the correlation proposed by Beckstead and model the combustion of aluminum particles in solid rocket propellants and examined the sensitivity of the model to changes in propellant surface temperature, propellant velocity, propellant surface radiation temperature, parcel count, particle diameter, turbulent Prandtl number, and turbulent Schmidt number. Yilmaz et al. [33] also examined the heat flux to objects outside of a firing solid propellant rocket motor plume by measuring the heat flux to gages located at various locations with respect to the rocket nozzle. Hence, the calculations of internal ballistics have become an important part of the research methods on the performance of pasty propellant rocket engines.
Many studies have focused on the internal ballistics of traditional solid rocket motor with complex propellant grain geometry, whereas there have been very few reports on the internal ballistics of the pasty propellant rocket engine. It is different from the traditional solid rocket motor. The pasty propellant continuously flows into the combustor during the operation of the engine. The propellant flow velocity should be considered in the process of burning surface change. Thus, it is of great importance to develop a change model of the burning surface of the pasty propellant and to investigate the effects of several key influential parameters on internal ballistic behaviors, including the ignition delay time, transport pipeline structure, free volume of the combustion chamber, mass flow rate, and flow velocity of the pasty propellant. This paper is aimed at developing a burning surface model for the pasty rocket engine with consideration of the initial burning stage, steady burning segment, and cut-off segment, and the pasty rocket engine test system was designed and conducted to validate the burning model. The remainder of this paper is organized as follows: Section 2 revisits the governing equations of internal ballistics and derives the burning surface model. Section 3 introduces the experimental system of the pasty rocket engine. Section 4 analyzes the results of the experiment and calculations for the pasty rocket engine.
2. Mathematical Models and Numerical Procedure
2.1. Internal Ballistic Equation
A zero-dimensional internal ballistic model is often used to calculate the pressure change in the combustion chamber for a solid rocket motor [25]. According to the principle of conservation of mass, the gas mass change rate in the combustion chamber is the difference between the gas generation rate and the mass flow rate of the gas discharged through the nozzle , namely,
where represents gas quality in the combustion chamber, is the density of the pasty propellant, is the area of the burning surface, is the pressure of the combustion chamber, is the area of the nozzle throat, is the characteristic velocity of the pasty propellant, and and represent burning rate coefficient and exponent of the propellant, respectively. is the average density of combustion gas, and is the free volume of the combustion chamber. And the meaning of all variables in this paper is listed in Nomenclature.
Differentiate the above formula (5), we can get
It can be seen that the gas mass change rate in the combustion chamber consists of two parts. represents the gas mass filled by the increase of the combustion chamber free volume per unit time. Because the pasty propellant is continuously added to the combustion chamber, the volume of the combustion chamber can be approximately considered constant (). represents the gas quality required to change the gas density per unit time. The equation of state is differentiated to get
where is the temperature of the combustion gas and is the gas constant. The combustion temperature keeps constant (), so
Substituting (9), (2), (3), and (4) into (1), we can get the zero-dimensional internal ballistic differential equation of the pasty rocket engine.
2.2. Burning Surface Change Process of Pasty Propellant in the Combustor
In the solid rocket motor, the burning surface of the grain is derived according to the geometrical burning law [34]. Different from the traditional solid rocket motor, the pasty propellant has a flow velocity, and the volume of the combustor can be approximately considered constant. For a pasty propellant rocket engine, once the pasty propellant flows into the combustion chamber through the transport pipeline, it will be ignited and burned while being supplied. The propellant burning surface changing process can be affected by the burning surface retreat and the supply flow rate of the pasty propellant pushed by the hydraulic cylinder piston rod. Therefore, both the burning rate and the flow velocity of the pasty propellant have significant effects on the burning surface change.
To analyze the entire burning surface change process of the pasty propellant in the combustion chamber, a cylinder grain of pasty propellant with the length of at the exit of the transport pipeline is selected, as shown in Figure 1. The changing process of the burning surface with the movement of the selected grain consists of two parts, the retreat of the burning surface and the forward flow of propellant. The burning surface of the grain retreats in the radial direction due to the combustion of pasty propellant with the retreating speed of the propellant burning rate . The pasty propellant flow in the axial direction with the velocity of is pushed by the hydraulic cylinder piston. The time when the front end of propellant flows through the pipeline exit is recorded as ; then, after a certain time interval , the position and geometric shape of the selected grain will change. The distance moves forward of the selected grain is , and the burned propellant web thickness is . The movement speed of the propellant grain burning surface is . The motion tracking is an oblique straight line and the angle between the motion direction and the horizontal direction is . In addition, when the burned propellant web thickness is equal to , the selected grain is completely burned, and the burning surface moving process of the selected grain can be considered as a cone, as shown by the dashed line in Figure 1. The bottom diameter of the cone is the diameter of the pipeline, and the height of the cone can be calculated by
2.3. Burning Surface Equation of the Pasty Propellant
Similar to the solid propellant rocket motor, we can also divide the burning process of the pasty propellant rocket engine into three stages: initial burning stage, steady burning, and burning tail-off. The cone-shaped burning surface model is used to derive the burning surface equation of the pasty propellant in each working stage.
2.3.1. Initial Burning Stage
The pasty propellant burning process involves very complex physical and chemical combustion phenomena. Both the ignition gas spreading and the propellant surface reaction can lead to the ignition delay of the pasty rocket engine. During this period, the pasty propellant will accumulate at the outlet of the transportation pipeline. This part of the propellant is called the initial accumulation of pasty propellant. The initial accumulation of the pasty propellant is approximately cylindrical, and the cylindrical bottom is the end face of the outlet of the transport pipeline, and the height of the cylinder is ; is the ignition delay time. After the accumulated pasty propellant is ignited, the combustion chamber is filled with high-temperature gas, and the pasty propellant squeezed out of the transport pipe will be ignited.
The ignition delay time measured in the experimental test is 0.08~0.16 s, and the initial stacking length of the propellant is estimated to be 16~32 mm. In the initial combustion section, the shape of the pasty propellant burning surface is divided into two parts. The first part of the pasty propellant burning surface is cylindrical, and the other part is a frustum of the cone due to the burning of the propellant extruded from the transport pipeline. The burning surface of the pasty propellant is composed of three parts, namely, a conical side surface , a cylindrical side surface , and a cylindrical end surface , as shown in Figure 2. The total burning surface area in this stage is calculated as where is the diameter of the transport pipeline, is the burned propellant web thickness, is the number of transport pipelines, and is the flow length of the propellant.
(a)
(b)
(c)
(d)
2.3.2. Steady Burning Segment
When the burned propellant web thickness is equal to the radius of the pipeline (), the pasty propellant reaches a steady burning stage. The pasty propellant is continuously supplied from the tank by the hydraulic cylinder piston, which is equivalent to countless small grains entering into the combustion chamber one by one; thus, a complete cone formed as shown in Figure 2(d). Therefore, the burning surface of the pasty propellant is a cone-side surface. The burning surface area is
where is the height of the cone, as seen in equation (11).
2.3.3. Burning Tail-Off
When the supply of the pasty propellant is stopped, and residual propellant is burned following the geometrical burning law, which is similar to the solid rocket motor, the burning surface of pasty propellant in the burning tail-off is shown in Figure 3. It can be computed by
where is the half-apex angle of the cone.
To solve differential equation (10), the fourth-order Runge-Kutta method [25] is used to calculate the pressure evolution in the combustion chamber, as shown in Figure 4.
3. Experiment Instruments
In order to validate the present burning surface model, experiments were carried out on a laboratory-scale test pasty rocket engine. Figure 5 shows the schematic of the test pasty rocket engine, which consists of a hydraulic system, piston, propellant tank, transport pipeline, combustion chamber, nozzle assembly, and pressure measurement equipment. The hydraulic system is used to supply the pasty propellant with a large driving force up to 9 MPa and a wide adjustment range. The supply flow rate of the pasty propellant can be controlled by the foreword velocity of the hydraulic cylinder piston rod. The pasty propellant tank is filled with propellant, and the pasty propellant enters into the combustion chamber through transport pipelines. The tank diameter is 160 mm, and the length of the pasty propellant tank is 300 mm. The designed pasty rocket engine operation time is 1 s. The transport pipelines are straight round pipes, which are distributed according to a certain law, as shown in Figure 6. The diameter and length of the combustor are 128 mm and 134 mm, respectively. The diameter of the nozzle throat is 16.9 mm, and the black powder is used to ignite the pasty propellant. Figure 7 presents the photographic view of the pasty rocket experimental systems.
When the control system issues an ignition command, and the hydraulic system starts pushing the piston at the same time. The pasty propellant, which is driven by the piston, enters the combustion chamber through the transport pipeline. It is ignited by hot gas generated from the black powder. The control system issues a termination command after the engine works for a certain period, and the hydraulic system stops working. Then, the pasty propellant supply stops, which is marked as the end of the pasty rocket engine. The combustion chamber pressure evolutions are obtained by the test acquisition. The pasty propellant used in this paper is produced by Xi’an Modern Chemistry Research Institute, and the general components of the pasty propellant are listed in Table 1.
Table 2 summarizes the experimental case studied in this paper. represents the mass flow rate of the pasty propellant. , , and are the diameter of the transport pipeline, the propellant tank, and nozzle throat, respectively. is the number of transport pipelines. represents the velocity of the pasty propellant through the transport pipeline. is the velocity of the piston, and is the ratio of pipe outlet area to the nozzle throat area.
4. Results and Discussion
4.1. Internal Ballistics of the Pasty Propellant Rocket Engine
The combustion chamber pressure evolutions of the pasty propellant rocker engine are simulated based on the zero-dimensional internal ballistic equation and burning surface change model described above. The diameter of the pipelines is mm, the number of transport pipelines is , and the flow velocity of the pasty propellant is 240 mm/s, as listed in Table 2. The physical parameters of the pasty propellant used in the present study are listed in Table 3.
Figure 8 illustrates the pressure histories in the combustion chamber for both experimental data and calculated results. It can be seen from the experimental data that there is an obvious ignition delay that appeared in the ignition stage, and the delay is mostly due to the time required to heat the cold propellant until ignition occurs. After the delay time period , the pressure trace increased quickly, then reached a stable value, and finally decreased. To analyze the internal ballistic characteristics of the pasty rocket engine, the pressure trace can be divided into three successive stages, namely, the ignition transient, steady burning segment, and the burning tail-off. When the pasty propellant is ignited and the engine starts to work, the pressure in the combustion chamber climbed quickly and then rapidly decreased to a stable value after reaching the initial pressure peak value , which is defined as ignition transient . The initial pressure peak occurs due to the ignition delay of the pasty propellant. The accumulated propellant resulted in a larger initial burning surface, which leads to the appearance of the initial pressure peak. This is different from the traditional solid rocket motor, whose initial pressure peak is induced mainly by erosion burning. In the steady burning stage, the pasty propellant maintains an almost constant burning surface, and this period is denoted as . In the burning tail-off, the pasty propellant stops supplying, and the residual propellant burns with a specific geometry. The pressure in the combustion chamber decreases rapidly, and this period is represented by residual burning time period .
In addition, it can be seen from Figure 8 that the calculated value of the pressure in the combustion chamber is in good agreement with the data obtained by the experiment. Table 4 shows the parameters of the experimental and calculated values of the pressure history, and the deviation of the initial pressure peak is around 4.02%, which indicates that the simplification made in the burning surface model is reasonable.
4.2. Effect of the Ignition Delay Time
The effect of the ignition delay time on the internal ballistics of the pasty propellant rocket engine was also studied. Five different values of the ignition delay time were employed, namely, s, 0.06 s, 0.08 s, 0.10 s, and 0.12 s. The diameter of the pipelines is mm, and the number of transport pipelines is . The free volume of the pasty rocket engine combustor is m3, and the flow velocity of the pasty propellant is 240 mm/s.
The calculated pressure evolutions in the combustor for different ignition delay times are shown in Figure 9. It can be noted that the evolutions of the pressure are qualitatively similar for all cases. The ignition delay time has a significant effect on the initial burning stage and the initial pressure spike . The pressure evolution exhibits little discrepancy for the equilibrium burning stage and the burning tail-off. For the different five ignition delay time cases, the calculated peak pressures in the combustion chamber are 3.63, 3.64, 3.83, 4.27, and 4.99 MPa, respectively. The mean pressure rise rates in the initial burning stage for ignition delay time of 0.04 s, 0.06 s, 0.08 s, 0.10 s, and 0.12 s are 21.5 MPa/s, 26.9 MPa/s, 37.1 MPa/s, 62.7 MPa/s, and 102.0 MPa/s, respectively. The peak value of the initial pressure grows by 37.5%, and the ignition transient reduces by 29.2% with the increase of ignition delay time. This is because that as the ignition delay time increases, the initial accumulation of pasty propellant and the initial burning surface area becomes larger during ignition, leading to an increase in the initial pressure peak as mentioned before. Therefore, the internal ballistic characteristics of the pasty propellant rocket engine can be improved by increasing the ignition powder or improving the formulation of the pasty propellant to reduce the ignition delay time.
4.3. Effect of the Transport Pipeline Structure
In order to study the influence of the transport pipeline structure on the internal ballistic characteristics, several values of transport pipeline diameter and transport pipe number were considered ( mm, 9.8 mm, 8.8 mm, 8.0 mm, and 7.4 mm and , 16, 20, 24, and 28) while the mass flow rate of pasty propellant was held constant. The free volume of the pasty rocket engine combustor is m3, the flow velocity of the pasty propellant is 240 mm/s, and the ignition delay time is set to 0.08 s.
Figure 10 illustrates the pressure evolutions in the combustor for different transport pipeline structures, while the values of the peak pressure , ignition transient , steady burning time period , and residual propellant burning time period are shown in Table 5. Note that the number and diameter of the transport pipe have a significant influence on the initial rapid pressurization, steady burning time period, and pressure drop process of the pasty rocket engine, while has little effect on the equilibrium pressure. As the transport pipe number increases (or the transport pipe diameter decreases), the initial pressure peak value and steady burning time period increase acutely, while the ignition transient is significantly reduced. When the transport pipe number changes from 12 to 28, the steady burning time period increases by 17.6%. However, the ignition transient and residual propellant burning time period decrease by 41.4% and 34.0%, respectively.
In the rapid rise of the initial pressure, the mean pressure rise rates for transport pipe numbers of 12, 16, 20, 24, and 28 are 18.0 MPa/s, 23.6 MPa/s, 30.0 MPa/s, 37.1 MPa/s, and 45.4 MPa/s, respectively. It is because that to keep a constant mass flow rate, a larger transport pipeline number comes with a smaller transport pipeline diameter, which increases the total initial burning surface area and causes the pressure to rise rapidly. With the increase of transport pipe number, the residual burning time becomes shorter while a relatively small discrepancy of the pressure descent rate is observed. This is due to that the burning time of the residual propellant can be approximately calculated by . Hence, when the mass flow rate of pasty propellant is held constant, the transport pipeline structure can affect not only the pressure spike of the initial burning stage but also the time period of the steady burning stage.
4.4. Effect of Free Volume of the Combustion Chamber
A parameter which can have a significant effect on the internal ballistics of the pasty propellant rocket engine is the free volume of the combustion chamber. A limited study of this effect is also carried out here, and several values of free volume are considered, namely, m3, m3, m3, m3, and m3. The diameter and number of the transport pipeline are set to mm and . The flow velocity of the pasty propellant is 240 mm/s, and the ignition delay time is set to 0.08 s.
Figure 11 shows the pressure evolutions in the combustor for different free volume of combustion chamber. Table 6 summarizes the numerical values of the peak pressure and initial combustion time under the four operating conditions. It can be seen from Figure 11 that the free volume of the combustion chamber has a great effect on the initial burning stage of the pasty rocket engine but has little effect on the equilibrium burning segment and burning tail-off. With the increase of free volume of the combustion chamber, the initial pressure spike increased and the time to reach the equilibrium pressure increased. For a large free volume of the combustor, the equilibrium time period is reduced. It is obvious that the smaller the free volume of the combustion chamber, the faster the pressure of the combustion chamber rises. The calculated pressure peak ratio increases from 1.24 to 1.42 with an increase of the free volume of the combustion chamber, and the time to achieve the equilibrium pressure increases from 0.18 s to 0.30 s. The reason for this phenomenon is that the decrease of the free volume of the combustion chamber will cause an increase in the pressure rise rate of the combustion chamber. While the burning rate of the pasty propellant has an exponential relationship with the pressure, so the average burning rate reaching the equilibrium segment increases, and the time to reach the equilibrium stage is reduced. Therefore, the free volume of the combustion chamber should be reduced so that the remnant of propellant due to incomplete combustion could be minimized.
4.5. Effect of Mass Flow Rate of the Propellant
Five different mass flow rates of the pasty propellant were taken into consideration here to study the effect of mass flow rate on the internal ballistic characteristics of the pasty rocket engine. The mass flow rates of the pasty propellant are 0.08 kg/s, 0.25 kg/s, 0.50 kg/s, 0.75 kg/s, and 1.00 kg/s, and the number of the transport pipeline is 4, 12, 24, 36, and 48, respectively. The flow velocity of the pasty propellant is 240 mm/s, and the ignition delay time is set to 0.08 s. The diameter of the pipeline is mm, the free volume of the pasty rocket engine combustor is m3, and we change the nozzle throat diameter to keep the equilibrium pressure of the combustion chamber at 3 MPa. The calculated pressure evolutions in the combustor for mass flow rate are shown in Figure 12.
As can be seen from Figure 12, the mass flow rate of the pasty propellant has a great effect on the initial burning stage of the pasty rocket engine and has little effect on the equilibrium burning stage and burning tail-off. The mean pressure rise rates increase while the initial pressure spike decreased with an increase of the mass flow rate of the pasty propellant.
It is obvious that when the mass flow rate kg/s, the pressure in the combustion chamber rises slowly after the engine is ignited. The initial pressure peak reached 4.31 MPa, and the time to reach the equilibrium period is 0.36 s. When the mass flow rate kg/s, the pressure in the combustion chamber rises quickly. The pressure peak is small, only 3.72 MPa, and the time to reach the equilibrium stage is 0.18 s. Table 7 lists the calculation results in each case. Therefore, we can conclude that the lower the mass flow rate, the slower the combustion chamber pressure rises, the higher the pressure peak, and the longer it takes to reach the equilibrium period. We should appropriately increase the mass flow rate of the pasty propellant when designing the rocket engine to obtain better internal ballistic performance.
4.6. Effect of the Flow Velocity of the Pasty Propellant
The effect of the flow velocity of the pasty propellant on the internal ballistics of the pasty propellant rocket engine was also studied. Different flow velocities from 180 mm/s to 360 mm/s were taken into consideration to study this effect. The diameter and number of the transport pipeline are set to mm and , and the ignition delay time is set to 0.08 s.
Figure 13 illustrates the pressure evolution trace with time for different flow velocities of the pasty propellant, and Table 8 lists the main parameters of the calculated results. Noted that the flow velocity of the pasty propellant has a significant influence on the initial rapid pressurization, initial pressure spike , and the equilibrium pressure . In the rapid rise of the initial pressure, the mean pressure rise rates for flow velocities of 180 mm/s, 240 mm/s, 300 mm/s, and 360 mm/s are 21.3 MPa/s, 37.1 MPa/s, 58.4 MPa/s, and 85.8 MPa/s, respectively.
As shown in Figure 14, it is clear that the initial pressure spike and equilibrium pressure increase linearly with the increase of the flow velocity of the pasty propellant, while the increase rate of the initial pressure spike is greater than the increase rate of the equilibrium pressure. This is mostly due to higher propellant flow velocity leads to more initial accumulation of the pasty propellant. However, the ignition transient decreases with the increase of the pasty propellant flow velocity. When the flow velocity of the pasty propellant increases from 180 mm/s to 360 mm/s, the ignition transient decreases by 30.4%.
In addition, to study the thrust adjustment characteristics of the pasty rocket engine, the pasty propellant flow velocity is changed during the operation process. In this case, the initial flow velocity of the pasty propellant is mm/s, and the flow velocity is set to mm/s after the engine works for one second. Then, the flow velocity is mm/s after one second. The calculated pressure evolution in the combustor with the variation of pasty propellant flow velocity is shown in Figure 15. As can be seen from Figure 15, obviously, the pressure in the combustion chamber changes with the flow velocity of the pasty propellant. When the flow velocity varies, the pressure in the combustion chamber responds quickly. Therefore, the pasty rocket engine thrust can be accurately adjusted by controlling the flow velocity of the pasty propellant.
5. Conclusions
In this paper, the combustion characteristic of the pasty propellant is studied both experimentally and numerically. The program calculated results are in good agreement with the experimental data. In particular, the impact of ignition delay time, structure of the transportation pipe, free volume of the combustion chamber, and mass flow rate of the pasty propellant on the internal ballistic performance are analyzed. Conclusions are summarized as follows: (1)During the stable operation of the pasty propellant rocket engine, the burning surface of the pasty propellant appears conical. The calculation model proposed in this paper is reasonable for the calculation of the internal ballistic characteristic parameters of the pasty propellant rocket engine, and the error of the initial pressure peak is only 4.02%(2)When the ignition delay time increased, the pressure peak raised faster. However, the value of the initial pressure peak in the combustion chamber increases with the increase of the ignition delay time due to the accumulation of the pasty propellant. As the diameter of the transport pipeline decreases, the initial burning time and residual propellant burning time of the engine become shorter. The transport pipe diameter changes from 11.3 mm to 7.4 mm, and the initial combustion time and residual propellant combustion time decreased by 41.3% and 36.0%(3)The reduction of the free volume of the combustion chamber can reduce the initial pressure peak of the pasty propellant rocket engine and the time to reach the equilibrium pressure. Therefore, the free volume of the combustion chamber should be reduced to control the remnant portion of the propellant(4)The larger mass flow rate of the pasty propellant makes the combustion chamber pressure rise faster and can reduce both the initial pressure peak and the time to reach the equilibrium in the combustion chamber. The initial pressure spike and equilibrium pressure increase linearly with the increase of the flow velocity of the pasty propellant while the ignition transient decreased with the increase of the pasty propellant flow velocity
For further study, experiments can be conducted to study the influence of the pasty propellant flow velocity changes on internal ballistics and obtain the shape of the pasty propellant grains during the burning process. The two-phase flow of the pasty propellant can also be studied.
Nomenclature
| : | Burning rate coefficient of propellant, m/(s·MPan) |
| : | Propellant burning surface area, m2 |
| : | The nozzle throat area, m2 |
| : | Characteristic velocity, m/s |
| : | Transport pipe diameter, m |
| : | The web thickness burned, m |
| : | The height of the cone, m |
| : | The distance moves forward, m |
| : | The initial stacking length, m |
| : | The mass flow rate of the pasty propellant, kg/s |
| : | The gas mass change rate in the combustion chamber, kg/s |
| : | The combustion gas generation rate, kg/s |
| : | The mass flow rate of the gas discharged through the nozzle, kg/s |
| : | Burning rate exponent of propellant |
| : | Number of the transport pipe |
| : | Pressure in combustion chamber, MPa |
| : | Equilibrium pressure, MPa |
| : | Initial pressure peak, MPa |
| : | Propellant burning rate, m/s |
| : | The combustion gas constant, J/(kg·K) |
| : | The ignition delay time, s |
| : | Initial burning time, s |
| : | Steady burning time, s |
| : | Residual burning time, s |
| : | Temperature in combustion chamber, K |
| : | Velocity of the pasty propellant flow forward, m/s |
| : | Velocity of the piston rod, m/s |
| : | Velocity of the grain surface move, m/s |
| : | The free volume of the combustion chamber, m3 |
| : | The angle between the speed direction and the horizontal |
| : | Specific heat ratio of gas |
| : | Density of combustion gas, kg/m3 |
| : | The pasty propellant density, kg/m3. |
Data Availability
The data used to support the findings of this study are included within the article.
Conflicts of Interest
The authors declare that they have no conflicts of interest.
Acknowledgments
This research was supported by the National Natural Science Foundation of China (No. 52006099), the Fundamental Research Funds for the Central Universities (No. 30920021102 and No. 309181B8812), and the Six Talent Peaks Project in Jiangsu Province of China (No. 2016-HKHT-017).