Abstract
Vehicle dynamic load is a major factor in the occurrence of early pavement failure. The analysis of tire–road contact pressure under various driving conditions of the vehicle is the basis for studying vehicle driving stability and road surface performance durability. In previous studies, there was more analysis of tire–road contact stress under static load. However, the results obtained in this way were quite different from the actual situation, because the various functional properties of the tire and the transmission of the interaction force between it and the road surface were better demonstrated during the movement of the vehicle. In this paper, the 205-55-R16 radial tire is used as the research object, and the finite element modeling software ABAQUS is used to establish a realistic three-dimensional tire–road contact model. This study discussed the effects of vehicle load and tire pressure on tire ground pressure distribution during static loading of the vehicle and simulated the tire ground pressure changes with speed or time under steady rolling, driving, and braking conditions. The results showed that the contact pressure under braking conditions is significantly greater than that under static conditions. Therefore, at intersections with frequent braking, the standard axle load for road mechanics calculations should be increased. The research helps to analyze the early damage to the road caused by vehicle driving, and provides references for road designers in road design.
Similar content being viewed by others
Data availability
All data, models, and code generated or used during the study appear in the submitted article.
References
Yu, Q.; Dai, Y.K.; Zhang, K.: Research on tire ground pressure distribution test under static load. Tire Ind. 04, 11–15 (1999)
Fwa, T.F.; Pasindu, H.R.; Ung, G.P.: Critical rut depth for pavement maintenance based on vehicle skidding and hydroplaning consideration. J. Transp. Eng. 138(4), 423–429 (2012)
Ju, F.; Fwa, T.F.; Ong, G.P.: Evaluating wet weather driving benef is of grooved pavements. Int. J. Pavement Res. Technol. 6(4), 287–293 (2013)
Pasindu, H.R.; Fwa, T.F.: Improving wet-weather runway performance using trapezoidal grooving design. Transp. Dev. Econ. 1(1), 1–10 (2015)
Tielking, J.T.; Roberts, F.L.: Tire contact pressure and its effect on pavement strain. J. Transp. Eng. 113(113), 56–71 (1987)
Burke, A.M.; Olatunbosun, O.A.: Static tire/road interface modeling. Meccanica 32, 473–479 (1997)
Liu, C.H.; Wong, J.Y.; Mang, H.A.: Large strain finite element analysis of sand: model, algorithm and application to numerical simulation of tire-sand interaction. Comput. Struct. 74(3), 253–265 (2000)
Walubita, L.F.: Modeling mechanistic responses in asphalt pavements under three-dimensional tire-pavement contact pressure. J. Cent. South Univ. Technol. 18(1), 250–258 (2011)
Bai, T., et al.: Viscoelastic modelling of an asphalt pavement based on actual tire-pavement contact pressure. Road Mater. Pavement Des. (2020). https://doi.org/10.1080/14680629.2020.1766545
Hu, X., et al.: Effects of tire inclination (turning traffic) and dynamic loading on the pavement stress–strain responses using 3-D finite element modeling. Int. J. Pavement Res. Technol. 10(4), 304–314 (2017)
Hu, X., et al.: Modelling tensile strain response in asphalt pavements: bottom-up and/or top-down fatigue crack initiation. Road Mater. Pavement Des. 10(1), 125–154 (2009)
Hu, X., et al.: Effects of layer interfacial bonding conditions on the mechanistic responses in asphalt pavements. J. Transp. Eng. 137(1), 28–36 (2011)
GB / T2977-2016, Specification, size, air pressure and load of truck tires, National Technical Committee for Tire and Rim Standardization (2016)
Liu M.L.: Numerical simulation analysis of tire pavement interaction. Harbin, Harbin Institute of Technology (2013)
Lu, W.C.; Xu, L.; Yuan, C.C.: Implementation method of active braking of vehicle active collision avoidance system. Mach. Manuf. Autom. 4, 195–198 (2017)
Wang, W.; Yuan, C.C.; He, Y.G.: Research on automobile horizontal active collision avoidance system based on μ control theory. Mach. Manuf. Autom. 257(04), 161–166 (2018)
Zhu, S.Z.: Numerical Simulation of Tire Anti-sliding Behavior Based on Macroscopic Texture of Pavement. Southeast University, Nanjing (2017)
Guo, M.; Zhou, X.: Tire-pavement contact stress characteristics and critical slip ratio at multiple working conditions. Adv. Mater. Sci. Eng. 2019, 1–11 (2019)
Shi, Y.P.; Zhou, Y.R.: Detailed Explanation of ABAQUS Finite Element Analysis Example. Machinery Industry Press (2006)
Design Code for Highway Asphalt Pavement JTG D50-2006, Beijing, People's Communications Press, 20
Lee, J.H.: Finite element modeling of interfacial forces and contact stresses of pneumatic tire on fresh snow for combined longitudinal and lateral slips. J. Terrramech. 48(3), 171–197 (2011)
Nakashima, H.; Oida, A.: Algorithm and implementation of soil-tire contace analysis code based on dynamic FE–DE method. J. Terrramech. 41(1), 127–137 (2004)
Li, Y.; Zuo, S.; Duan, X., et al.: Theory analysis of the steady-state surface temperature on rolling tire. Proc. Inst. Mech. Eng. Part C J. Mech. Eng. Sci. 226(5), 1278–1289 (2012)
Duan, X.L.; Zuo, S.G.; Li, Y., et al.: Test and finite element simulation of steady-state temperature field of rolling tire. Appl. Mech. Mater. 236, 536–542 (2012)
Acknowledgements
This work was sponsored by the National Key R&D Program of China (Grant No. 2018YFE0103800), and Fundamental Research Funds for the Central Universities, CHD (Grant No. 300102219316). The authors gratefully acknowledge their financial support.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Yu, L., Hu, J., Li, R. et al. Tire-Pavement Contact Pressure Distribution Analysis Based on ABAQUS Simulation. Arab J Sci Eng 47, 4119–4132 (2022). https://doi.org/10.1007/s13369-021-05903-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13369-021-05903-1