Skip to main content
SpringerLink
Log in

Electrical Discharge Machining of Parts Produced by Additive Technology

  • Published:
Russian Engineering Research Aims and scope

Abstract

The electrical discharge machining (EDM) of parts produced by additive technology is experimentally studied. The influence of wire-cut EDM on the final surface roughness of a titanium workpiece produced by additive technology is described by means of a regression equation.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.

Similar content being viewed by others

REFERENCES

  1. Zlenko, M.A., Popovich, A.A., and Mutylina, I.N., Additivnye tekhnologii v mashinostroenii: Uchebnoe posobie (Additive Technologies in Machine Engineering: Manual), St. Petersburg: S.-Peterb. Gos. Politekh. Univ., 2013.

  2. Shlykov, E.S. and Ablyaz, T.R., Wear of the electrode-tool during copy-piercing electrical discharge machining of bimetals, Sovrem. Probl. Nauki Obraz., 2015, no. 2-1. https://science-education.ru/ru/article/ view?id=20539.

  3. Grisharin, A.O., Ablyaz, T.R., and Ogleznev, N.D., Efficiency of electrical discharge machining of hydraulic-cylinder parts and special-purpose products using electrodes-tools with higher electrical discharge properties, Vestn. Perm. Nats. Issled. Politekh. Univ., 2017, vol. 19, no. 3, pp. 151–162.

  4. Ablyaz, T.R., Khanov, A.M., and Khurmatullin, O.G., Sovremennye podkhody i tekhnologii elektroerozionnoi obarabotki materialov: uchebnoe posobie (Modern Approaches and Technologies of EDM Processing of the Materials: Manual), Perm: Perm. Nats. Issled. Politekh. Univ., 2012.

  5. Patel Vijay, D., Patel, D.M., Patel, U.J., et al., Review of wire-cut EDM process on titanium alloy, Int. J. Eng. Res. Appl., 2014, vol. 4, no. 12, pp. 112–121.

    Google Scholar 

  6. Rebrova, I.A., Planirovanie eksperimenta: Uchebnoe posobie (Experiment Planning: Manual), Omsk: Sib. Avtom.-Dorozhn. Inst., 2010.

Download references

Funding

Financial support was provided by the Russian Ministry of Science and Higher Education (project FSNM-2020-0028).

Author information

Authors and Affiliations

  1. Perm National Research Polytechnic University, Perm, Russia

    E. S. Shlykov, T. R. Ablyaz, K. R. Muratov, V. V. Shiryaev, R. M. Aliev & A. D. Sultanov

Authors
  1. E. S. Shlykov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. T. R. Ablyaz
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. K. R. Muratov
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. V. V. Shiryaev
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. R. M. Aliev
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. A. D. Sultanov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to E. S. Shlykov, T. R. Ablyaz, K. R. Muratov or V. V. Shiryaev.

Additional information

Translated by B. Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Shlykov, E.S., Ablyaz, T.R., Muratov, K.R. et al. Electrical Discharge Machining of Parts Produced by Additive Technology. Russ. Engin. Res. 41, 455–456 (2021). https://doi.org/10.3103/S1068798X2105021X

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X2105021X

Keywords:

Search

Navigation