Abstract
The effect of oxygen on the microstructure and mechanical properties of thermally treated rocks is a matter of rock engineering. For comparative analysis, in this study, the sandstone specimens were heated in a vacuum and aerobic environment. It was subsequently subjected to a series of scanning electron microscopy (SEM), P-wave velocity, X-ray diffraction (XRD), and surface colour observation tests. The effect of oxygen on the thermal damage mechanism of sandstone was studied according to the diversities in sandstone microstructure and mineral composition under different heating environments. Then, static and dynamic compression tests were carried out on the heated specimens under different environments; the effect of oxygen on the mechanical properties of sandstone was studied. The results show that the initial temperature of the mineral oxidation reaction was the threshold temperature at which the microstructure, mineral composition, and mechanical parameters of the specimen were heated in different environments to diverge. As the temperature rose, the oxidation reaction of pyrite and chlorite, and related chemical reactions gradually deepened, the thermal damage and mechanical properties of specimens heated in an aerobic environment were more deteriorated than that of the vacuum environment. Therefore, it can be inferred that the oxidation reaction of minerals at high temperatures exacerbated the thermal damage to the sandstone and led to a further deterioration in its mechanical properties. This has important implications for stability analysis of high-temperature rock engineering in aerobic environments.
Similar content being viewed by others
References
Akbar MNA, Szabó NP (2019) The effects of pore geometry and pore structure in characterizing the P-wave velocity and quality factor in sandstone reservoirs. Magy Geofiz 60:40–46
Bieniawski ZT, Hawkes I (1978) International-society-for-rock-mechanics-commission-on-standardization-of-laboratory-and-field-tests-suggested methods for determining tensile-strength of rock materials. Int J Rock Mech Min Sci 15:99–103
Bryers RW (1996) Fireside slagging, fouling, and high-temperature corrosion of heat-transfer surface due to impurities in steam-raising fuels. Prog Energy Combust Sci 22:29–120. https://doi.org/10.1016/0360-1285(95)00012-7
Chen GQ, Li TB, Zhang GF, Yin HY, Zhang H (2014) Temperature effect of rock burst for hard rock in deep-buried tunnel. Nat Hazards 72:915–926. https://doi.org/10.1007/s11069-014-1042-6
Chen HQ, Meng LB (2019) Mechanical characteristics and acoustic emission characteristics of limestone triaxial unloading after high temperature effect. Saf Coal Mines 50:58–62. https://doi.org/10.13347/j.cnki.mkaq.2019.04.014
Dai LD, Li HP, Hu HY, Shan SM (2008) Experimental study of grain boundary electrical conductivities of dry synthetic peridotite under high-temperature, high-pressure, and different oxygen fugacity conditions. J Geophys Res-Solid Earth 113:1–9. https://doi.org/10.1029/2008JB005820
Dai LD, Hu HY, Li HP, Wu L, Hui KS, Jiang JJ, Sun WQ (2016) Influence of temperature, pressure, and oxygen fugacity on the electrical conductivity of dry eclogite, and geophysical implications. Geochem Geophys Geosyst 17:2394–2407. https://doi.org/10.1002/2016GC006282
Fan C, Yan JW, Huang YR, Han XX, Jiang XM (2015) XRD and TG-FTIR study of the effect of mineral matrix on the pyrolysis and combustion of organic matter in shale char. Fuel 139:502–510. https://doi.org/10.1016/j.fuel.2014.09.021
Funatsu T, Kuruppu M, Matsui K (2014) Effects of temperature and confining pressure on mixed-mode (I-II) and mode II fracture toughness of Kimachi sandstone. Int J Rock Mech Min Sci 67:1–8. https://doi.org/10.1016/j.ijrmms.2013.12.009
Gray D, Roberts G, Head K (2002) Recent advances in determination of fracture strike and crack density from P-wave seismic data. Geophysics 21:280–285. https://doi.org/10.1190/1.1463778
Hong L, Li XB, Ma CD, Yin TB, Ye ZY, Liao GY (2008) Study on size effect of rock dynamic strength and strain rate sensitivity. Chin J Rock Mech Eng 27:526–533
Kanaori Y (1983) The observation of crack development around an underground rock chamber by borehole television system. Rock Mech Rock Eng 16:133–142. https://doi.org/10.1007/BF01032795
Kargal’tsev AK, Volovetskii MV, Kadik AA, Lukanin OA (2009) A high-temperature furnace with a controlled oxygen regime for studying phase and redox reactions in silicate and oxide systems at 1 atm. Geochem Int 47:725–730. https://doi.org/10.1134/S0016702909070064
Koch E (2010) The differential calorimetric study of the reactivity of unstable compounds. Angew Chem-Int Edit 9:288–300. https://doi.org/10.1002/anie.197002881
Kong B, Wang EY, Li ZH, Wang XR, Liu XF, Li N, Yang YL (2016a) Electromagnetic radiation characteristics and mechanical properties of deformed and fractured sandstone after high temperature treatment. Eng Geol 209:82–92. https://doi.org/10.1016/j.enggeo.2016.05.009
Kong B, Wang EY, Li ZH, Wang XR, Liu J, Li N (2016b) Fracture mechanical behavior of sandstone subjected to high-temperature treatment and its acoustic emission characteristics under uniaxial compression conditions. Rock Mech Rock Eng 49:4911–4918. https://doi.org/10.1007/s00603-016-1011-3
Lei RD, Wang Y, Zhang L, Liu BL, Long K, Luo P, Wang YK (2019) The evolution of sandstone microstructure and mechanical properties with thermal damage. Energy Sci Eng 7:3058–3075. https://doi.org/10.1002/ese3.480
Liu QS, Qian ZC, Wu ZJ (2019) Micro/macro physical and mechanical variation of red sandstone subjected to cyclic heating and cooling: an experimental study. Bull Eng Geol Environ 78:1485–1499. https://doi.org/10.1007/s10064-017-1196-z
Liu S, Xu JY (2014a) Investigation of impact compressive mechanical properties of sandstone after as well as under high temperature. High Temp Mater Process 33:585–591. https://doi.org/10.1515/htmp-2013-0125
Liu S, Xu JY (2014b) Mechanical properties of Qinling biotite granite after high temperature treatment. Int J Rock Mech Min Sci 71:188–193. https://doi.org/10.1016/j.ijrmms.2014.07.008
Liu S, Xu JY (2015) Analysis on damage mechanical characteristics of marble exposed to high temperature. Int J Damage Mech 24:1180–1193. https://doi.org/10.1177/1056789515570507
Luo J, Wang LG (2011) High-temperature mechanical properties of mudstone in the process of underground coal gasification. Rock Mech Rock Eng 44:749–754. https://doi.org/10.1007/s00603-011-0168-z
Ma LP, Ning P, Zheng SC, Niu XK, Zhang W, Du YL (2010) Reaction mechanism and kinetic analysis of the decomposition of phosphogypsum via a solid-state reaction. Ind Eng Chem Res 49:3597–3602. https://doi.org/10.1021/ie901950y
Ma LZ, Ning P, Qing S (2009) Study on influence factors between high sulfur coal and phosphogypsum. Acta Sci Nat Univ Sunyatseni 48:85–88
Mao XB, Zhang LY, Liu RX, Ma D (2014) Mechanical and thermal damage properties of sandstone at high temperatures. Electron J Geotech Eng 19:3137–3150. https://doi.org/10.1109/JLT.2003.821766
Meng H, Li QM (2003) Correlation between the accuracy of a SHPB test and the stress uniformity based on numerical experiments. Int J Impact Eng 28:537–555 https://doi.org/10.1016/S0734-743X(02)00073-8
Nasseri MHB, Tatone BSA, Grasselli G, Young RP (2009) Fracture toughness and fracture roughness interrelationship in thermally treated westerly granite. Pure Appl Geophys 166:801–822. https://doi.org/10.1007/s00024-009-0476-3
Peng Z, Redfern SAT (2013) Mechanical properties of quartz at the α-β phase transition: implications for tectonic and seismic anomalies. Geochem Geophys Geosyst 14:18–28. https://doi.org/10.1029/2012gc004482
Sabourin JL, Yetter RA (2009) High-temperature heterogeneous reaction kinetics of tungsten oxidation by CO2, CO, and O2. J Propul Power 25:490–498. https://doi.org/10.2514/1.38123
Shen HM, Li XY, Li Q, Wang HB (2020) A method to model the effect of pre-existing cracks on P-wave velocity in rocks. J Rock Mech Geotech Eng 12:493–506. https://doi.org/10.1016/j.jrmge.2019.10.001
Sirdesai NN, Mahanta B, Singh TN, Ranjith PG (2016) Elastic modulus of thermally treated fine grained sandstone using non-contact laser extensometer. RARE 91:105–109
Sirdesai NN, Singh A, Sharma LK, Singh R, Singh TN (2018) Determination of thermal damage in rock specimen using intelligent techniques. Eng Geol 239:179–194. https://doi.org/10.1016/j.enggeo.2018.03.027
Sirdesai NN, Singh TN, Ranjith PG, Singh R (2017) Effect of varied durations of thermal treatment on the tensile strength of red sandstone. Rock Mech Rock Eng 50:205–213. https://doi.org/10.1007/s00603-016-1047-4
Tian H, Kempka T, Yu S, Ziegler M (2016) Mechanical properties of sandstones exposed to high temperature. Rock Mech Rock Eng 49:321–327. https://doi.org/10.1007/s00603-015-0724-z
Tomeczek J, Palugniok H (2002) Kinetics of mineral matter transformation during coal combustion. Fuel 81:1251–1258. https://doi.org/10.1016/S0016-2361(02)00027-3
Tong JJ, Karakus M, Wang MN, Dong CY, Tang XH (2016) Shear strength characteristics of shotcrete-rock interface for a tunnel driven in high rock temperature environment. Geomech Geophys Geo-Energy Geo-Resour 2:331–341. https://doi.org/10.1007/s40948-016-0039-x
Vassileva CG, Vassilev SV (2005) Behaviour of inorganic matter during heating of Bulgarian coals. Fuel Process Technol 86:1297–1333. https://doi.org/10.1016/j.fuproc.2005.01.024
Volovetskii MV, Lukanin OA, Rusakov VS, Kargal’tsev AA (2012) Influence of oxygen fugacity and temperature on the redox state of iron in natural silicic aluminosilicate melts. Geochem Int 50:330–343. https://doi.org/10.1134/S0016702912040088
Wang P, Yin TB, Li XB, Zhang SS, Bai L (2019) Dynamic properties of thermally treated granite subjected to cyclic impact loading. Rock Mech Rock Eng 52:991–1010. https://doi.org/10.1007/s00603-018-1606-y
Wilkomirsky I, Otero A, Balladares E (2010) Kinetics and reaction mechanisms of high-temperature flash oxidation of molybdenite. Metall Mater Trans B-Proc Metall Mater Proc Sci 41:63–73. https://doi.org/10.1007/s11663-009-9313-4
Yang SQ, Ranjith PG, Jing HW, Tian WL, Ju Y (2017a) An experimental investigation on thermal damage and failure mechanical behavior of granite after exposure to different high temperature treatments. Geothermics 65:180–197. https://doi.org/10.1016/j.geothermics.2016.09.008
Yang SQ, Xu P, Li YB, Huang YH (2017b) Experimental investigation on triaxial mechanical and permeability behavior of sandstone after exposure to different high temperature treatments. Geothermics 69:93–109. https://doi.org/10.1016/j.geothermics.2017.04.009
Yao MD, Rong G, Zhou CB, Peng J (2016) Effects of thermal damage and confining pressure on the mechanical properties of coarse marble. Rock Mech Rock Eng 49:2043–2054. https://doi.org/10.1007/s00603-016-0916-1
Yin TB, Wang P, Li XB, Wu BB, Tao M, Shu RH (2016a) Determination of dynamic flexural tensile strength of thermally treated Laurentian granite using semi-circular specimens. Rock Mech Rock Eng 49:3887–3898. https://doi.org/10.1007/s00603-016-0920-5
Yin TB, Li XB, Xia KW, Huang S (2012) Effect of thermal treatment on the dynamic fracture toughness of Laurentian granite. Rock Mech Rock Eng 45:1087–1094. https://doi.org/10.1007/s00603-012-0240-3
Yin TB, Wang P, Li XB, Shu RH, Ye ZY (2016b) Effects of thermal treatment on physical and mechanical characteristics of coal rock. J Cent South Univ 23:2336–2345. https://doi.org/10.1007/s11771-016-3292-9
Yin TB, Wang P, Yang J, Li XB (2018) Mechanical behaviors and damage constitutive model of thermally treated sandstone under impact loading. IEEE Access 6:72047–72062. https://doi.org/10.1109/ACCESS.2018.2881729
Zhang LY, Mao XB, Liu RX, Guo XQ, Ma D (2014) The mechanical properties of mudstone at high temperatures: an experimental study. Rock Mech Rock Eng 47:1479–1484. https://doi.org/10.1007/s00603-013-0435-2
Zhang WQ, Sun Q, Hao SQ, Wang B (2016a) Experimental study on the thermal damage characteristics of limestone and underlying mechanism. Rock Mech Rock Eng 49:2999–3008. https://doi.org/10.1007/s00603-016-0983-3
Zhang WQ, Sun Q, Hao SQ, Geng JS, Lv C (2016b) Experimental study on the variation of physical and mechanical properties of rock after high temperature treatment. Appl Therm Eng 98:1297–1304. https://doi.org/10.1016/j.applthermaleng.2016.01.010
Zhang QB, Zhao J (2014) A review of dynamic experimental techniques and mechanical behaviour of rock materials. Rock Mech Rock Eng 47:1411–1478. https://doi.org/10.1007/s00603-013-0463-y
Zhao J, Feng XT, Zhang XW, Zhang Y, Zhou YY, Yang CX (2018) Brittle-ductile transition and failure mechanism of Jinping marble under true triaxial compression. Eng Geol 232:160–170. https://doi.org/10.1016/j.enggeo.2017.11.008
Zhou YX, Xia K, Li XB, Li HB, Ma GW, Zhao J, Zhou ZL, Dai F (2011) Suggested methods for determining the dynamic strength parameters and mode-I fracture toughness of rock materials. Int J Rock Mech Min Sci 49:105–112. https://doi.org/10.1016/j.ijrmms.2011.10.004
Zuo JP, Li YL, Zhang XY, Zhao ZH, Wang TZ (2018) The effects of thermal treatments on the subcritical crack growth of Pingdingshan sandstone at elevated high temperatures. Rock Mech Rock Eng 51:3439–3454. https://doi.org/10.1007/s00603-018-1527-9
Zuo JP, Xie HP, Dai F, Ju Y (2014) Three-point bending test investigation of the fracture behavior of siltstone after thermal treatment. Int J Rock Mech Min Sci 70:133–143. https://doi.org/10.1016/j.ijrmms.2014.04.005
Acknowledgements
The authors would like to thank their colleagues of the High Temperature Rock Mechanics research group at the Central South University for technical discussion and comments.
Funding
This work was supported in part by the National Natural Science Foundation of China under Grant 41972283 and the National Natural Science Foundation of China under Grant 51774325.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Yin, T., Zhuang, D., Li, Q. et al. Effect of oxygen on damage mechanism and mechanical properties of sandstone at high temperature. Bull Eng Geol Environ 80, 6047–6064 (2021). https://doi.org/10.1007/s10064-021-02317-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10064-021-02317-z