Abstract
Metal powder bed fusion in additive manufacturing is gaining interest as a manufacturing technique for complex metal parts in the aerospace, rail, and automotive industries. This has led to an emergence of 3D printers in the market to accelerate the diffusion of this technology as an industrial manufacturing technique. The Aeroswift is an additive manufacturing machine developed with the purpose of using high laser powers for high-speed production of structurally dense parts at accelerated consolidation rates. The work in this paper focuses on the 3D printing of Ti-6Al-4V tensile specimens with the aim of determining the effect of fast cooling rate and porosity on the ductility of the specimen. The mechanical properties of the parts depend on the energy input; in order to obtain optimum melting of powder and desirable properties, an exponential decay relationship was observed where, as porosity increased, the elongation dropped. The level of porosity at low energy density is attributed to lack of fusion from low heat input, while high energy inputs showed low porosity.
Similar content being viewed by others
Data availability
The raw/processed data required to reproduce these findings cannot be shared at this time as the data also forms part of an ongoing study.
References
Haar GMT, Becker TH (2018) Selective laser melting produced Ti-6Al-4V: post-process heat treatments to achieve superior tensile properties. Materials 11:146–161
Shipley H, McDonnell D, Culleton M, Coull R, Lupoi R, O'Donnell G, Trimble D (2018) Optimisation of process parameters to address fundamental challenges during selective laser melting of Ti-6Al-4V: a review. Int J Mach Tools Manuf 128:1–20
Liu S, Shin YC (2019) Additive manufacturing of Ti6Al4V alloy: a review. Mater Des 164:107552
Kabir MR, Richter H (2017) Modeling of Processing-induced pore morphology in an additively-manufactured Ti-6Al-4V alloy. Materials 10(2):145
Promoppatum, P., et al. (2018) Numerical modeling and experimental validation of thermal history and microstructure for additive manufacturing of an Inconel 718 product. Progress in Additive Manufacturing, Numerical modeling and experimental validation of thermal history and microstructure for additive manufacturing of an Inconel 718 product.
Mathe NR, Tshabalala LC (2019) The validation of the microstructural evolution of selective laser-melted AlSi10Mg on the in-house built machine: energy density studies. Progress in Additive Manufacturing 4(4):431–442
Kumar KS (2014) Analytical modeling of temperature distribution, peak temperature, cooling rate and thermal cycles in a solid work piece welded by laser welding process. Procedia Mater Sci 6:821–834
Background on Laser Processing, in Principles of Laser Materials Processing. p. 407-430.
Shunmugavel M, Goldberg M, Polishetty A, Nomani J, Sun S, Littlefair G (2019) Chip formation characteristics of selective laser melted Ti–6Al–4V. Aust J Mech Eng 17(2):109–126
Majumdar T, Bazin T, Massahud Carvalho Ribeiro E, Frith JE, Birbilis N (2019) Understanding the effects of PBF process parameter interplay on Ti-6Al-4V surface properties. PLoS One 14(8):e0221198
Madikizela C, Cornish LA, Chown LH, Möller H (2019) Microstructure and mechanical properties of selective laser melted Ti-3Al-8V-6Cr-4Zr-4Mo compared to Ti-6Al-4V. Mater Sci Eng A 747:225–231
Yan X, Yin S, Chen C, Huang C, Bolot R, Lupoi R, Kuang M, Ma W, Coddet C, Liao H, Liu M (2018) Effect of heat treatment on the phase transformation and mechanical properties of Ti6Al4V fabricated by selective laser melting. J Alloys Compd 764:1056–1071
Mfusi BJ et al (2019) The effect of stress relief on the mechanical and fatigue properties of additively manufactured AlSi10Mg Parts. Metals 9(11):1216
Zhang B, Li Y, Bai Q (2017) Defect formation mechanisms in selective laser melting: a review. Chinese Journal of Mechanical Engineering 30(3):515–527
Tshabalala LC, Mathe N, Chikwanda H (2018) Characterization of gas atomized Ti-6Al-4V powders for additive manufacturing. Key Eng Mater 770:3–8
Jojo N et al (2019) Thermal modelling of pulsed laser ablation of silicon nitride ceramics. in Chemistry for a Clean and Healthy Planet. Springer International Publishing, Cham
Balla VK, Bodhak S, Bose S, Bandyopadhyay A (2010) Porous tantalum structures for bone implants: fabrication, mechanical and in vitro biological properties. Acta Biomater 6(8):3349–3359
Liu H, Li M, Qin X, Huang S, Hong F (2019) Numerical simulation and experimental analysis of wide-beam laser cladding. Int J Adv Manuf Technol 100(1):237–249
Lütjering G (1998) Influence of processing on microstructure and mechanical properties of (α+β) titanium alloys. Mater Sci Eng A 243(1):32–45
Kumar P, Chandran KSR (2017) Strength–ductility property maps of powder metallurgy (PM) Ti-6Al-4V alloy: a critical review of processing-structure-property relationships. Metall Mater Trans A 48(5):2301–2319
Vrancken B, Thijs L, Kruth JP, van Humbeeck J (2012) Heat treatment of Ti6Al4V produced by selective laser melting: microstructure and mechanical properties. J Alloys Compd 541:177–185
Zhao ZY, L L, Bai PK (2018) The Heat Treatment influence on the microstructure and hardness of TC4 titanium alloy manufactured via selective laser melting. Materials (Basel) 11:1318
du Plessis A, Sperling P, Beerlink A, Tshabalala L, Hoosain S, Mathe N, le Roux SG (2018) Standard method for microCT-based additive manufacturing quality control 1: porosity analysis. MethodsX 5:1102–1110
Zhao X, Li S, Zhang M, Liu Y, Sercombe TB, Wang S, Hao Y, Yang R, Murr LE (2016) Comparison of the microstructures and mechanical properties of Ti–6Al–4V fabricated by selective laser melting and electron beam melting. Mater Des 95:21–31
Bruno J, Rochman A, Cassar G (2017) Effect of build orientation of electron beam melting on microstructure and mechanical properties of Ti-6Al-4V. J Mater Eng Perform 26(2):692–703
Acknowledgements
The authors will like to acknowledge the Department of Science and Technology, CSIR National Laser Centre on the Aeroswift programme for funding and sample production. Stellenbosch University CT Scanner Facility and CSIR Materials Science & Manufacturing Mechanical Laboratory are also acknowledged for sample characterization.
Funding
This study was funded by the Department of Science and Innovation South Africa and CSIR South Africa.
Author information
Authors and Affiliations
Contributions
Mathe (conceptualize, data analysis, writing), Tshabalala (conceptualize, data analysis, writing), Hoosain (processing, data analysis, writing), Motibane (data analysis, writing), Du Plessis (micro-CT analysis, writing)
Corresponding authors
Ethics declarations
Ethics approval
Not applicable
Consent to participate
The consent is granted.
Consent for publication
The consent to publish is granted by all the authors.
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Mathe, N.R., Tshabalala, L.C., Hoosain, S. et al. The effect of porosity on the mechanical properties of Ti-6Al-4V components manufactured by high-power selective laser melting. Int J Adv Manuf Technol 115, 3589–3597 (2021). https://doi.org/10.1007/s00170-021-07326-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-021-07326-6