Abstract
Modern diesel engines are struggling to enhance the power density. This is usually realized by being equipped with a turbocharger, which demands higher performances on exhaust flow and exhaust waste energy recovery (WER). In the present study, we investigated the variations of exhaust flow and exhaust energy recovery performance with different geometrical parameters of exhaust system and proposed an evaluation and optimal design method of the exhaust system for a turbocharging diesel engine with a module pulse converter (MPC) system. The macro engine performances and the micro flow fields in exhaust system are obtained from the one/three dimensional (1D-3D) coupling simulation, and the energy of exhaust gas is quantified and analyzed with a concept of air power. It can be concluded that with a view to the exhaust performance and exhaust energy utilization, the diameter of the exhaust pipe should be set equal to the outlet diameter of the manifold and there is an optimized value of the contraction rate of the exhaust manifold. Besides, a parameter of the exhaust system called power potential coefficient is proposed to qualitatively evaluate the exhaust performance and exhaust energy.
Similar content being viewed by others
Abbreviations
- D:
-
exhaust pipe diameter, mm
- d:
-
exhaust manifold diameter, mm
- κ :
-
power potential coefficient, -
- φ :
-
manifold contraction rate, -
- in:
-
value at the inlet
- ex:
-
value at the outlet
References
Azuma, T., Tokunaga, Y. and Yura. T. (1981). Characteristics of exhaust gas pulsation of constant pressure turbo-charged marine diesel engines. J. Engineering for Gas Turbines and Power 102, 4, 827–835.
Cui, Y., Gu, H., Deng, K. and Yang, S. (2010). Study on mixed pulse converter (MIXPC) turbocharging system and its application in marine diesel engines. J. Ship Research 54, 1, 68–77.
Cai, M., Kawashima, K. and Kagawa, T. (2006). Power assessment of flowing compressed air. J. Fluids Engineering-Trans. Asme, 128, 402–405.
Chao, W., Nilsson, H., Yang, J. and Petit, O. (2016). 1D-3D coupling for hydraulic system transient simulations. Computer Physics Communications, 210, 1–9.
D’Errico, G., Cerri, T. and Pertusi, G. (2011). Multi-objective optimization of internal combustion engine by means of 1D fluid-dynamic models. Applied Energy 88, 3, 767–777.
De Bellis, V., Bozza, F., Siano, D. and Gimelli, A. (2013). Fuel consumption optimization and noise reduction in a spark-ignition turbocharged VVA engine. SAE Int. J. Engines 6, 2, 1262–1274.
Dincer, I. and Rosen, M. A. (2012). Exergy: Energy, Environment and Sustainable Development. 2nd edn. Elsevier. Amsterdam, Netherlands.
Feneley, A. J., Pesiridis, A. and Andwari, A. M. (2017). Variable geometry turbocharger technologies for exhaust energy recovery and boosting-a review. Renewable and Sustainable Energy Reviews, 71, 959–975.
Jacobs, T. J., Jagmin, C., Williamson, W. J., Filipi, Z. S., Assanis, D. and Bryzik, W. (2008). Performance and emission enhancements of a variable geometry turbocharger on a heavy-duty diesel engine. Int. J. Heavy Vehicle Systems 15, 2–4, 170–187.
Kesgin, U. (2005). Study on the design of inlet and exhaust system of a stationary internal combustion engine. Energy Conversion and Management, 46, 13–14, 2258–2287.
Li, K. W. (1995). Applied Thermodynamics: Availability Method and Energy Conversion. CRC Press. Boca Raton, FL, USA.
Mahabadipour, H., Krishnan, S. R. and Srinivasan, K. K. (2018). Investigation of exhaust flow and exergy fluctuations in a diesel engine. Applied Thermal Engineering, 147, 856–865.
Millo, F., Perazzo, A. and Pautasso, E. (2010). Optimizing the calibration of a turbocharged GDI engine through numerical simulation and direct optimization. SAE Int. J. Engines 3, 1, 556–570.
Montenegro, G., and Onorati, A. (2008). Modeling of silencers for IC engine intake and exhaust systems by means of an integrated 1D-multiD approach. SAE Int. J. Engines 1, 1, 466–479.
Montenegro, G., Onorati, A., Piscaglia, F. and D’Errico, G. (2007). Integrated 1D-multid fluid dynamic models for the simulation of ICE intake and exhaust systems. SAE Technical Paper No. 2007-01-0495.
Omran, R., Younes, R. and Champoussin, J. C. (2008). Neural networks for real-time nonlinear control of a variable geometry turbocharged diesel engine. Int.l J. Robust and Nonlinear Control 18, 12, 1209–1229.
Pesiridis, A. (2014). Automotive Exhaust Emissions and Energy Recovery. Nova Science Pubkishers. Hauppauge, NY, USA.
Rakopoulos, C. D. and Giakoumis, E. G. (2009). Diesel Engine Transient Operation: Principles of Operation and Simulation Analysis. Springer Science & Business Media. Berlin, Germany.
Shi, L., Wang, S., Deng, K. and Cui, Y. (2012). Variable geometry exhaust manifold turbocharging system for an 8-cylinder marine diesel engine. J. Marine Science and Technology 17, 2, 252–259.
Watson, N. and Janota, M. (1982). Turbocharging the Internal Combustion Engine. Macmillan International Higher Education. Heidelberg, Germany.
Yang, S., Wang, L. S., Gu, H., Deng, K. and Cui, Y. (2006). MIXPC turbocharging system for diesel engines. SAE Technical Paper No. 2006-01-339.
Acknowledgement
The authors gratefully acknowledge support by the National Natural Science Foundation of China (Grant No.: 51976011).
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Liu, F., Sun, C., Li, Y. et al. Performance Analysis and Optimization Design of Exhaust System for Turbocharging Diesel Engines. Int.J Automot. Technol. 22, 735–745 (2021). https://doi.org/10.1007/s12239-021-0067-6
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12239-021-0067-6