Skip to main content
SpringerLink
Log in

Three-dimensional modeling and reconstructive change of residual stress during machining process of milling, polishing, heat treatment, vibratory finishing, and shot peening of fan blade

  • Published:
Advances in Manufacturing Aims and scope Submit manuscript

Abstract

Residual stress during the machining process has always been a research hotspot, especially for aero-engine blades. The three-dimensional modeling and reconstructive laws of residual stress among various processes in the machining process of the fan blade is studied in this paper. The fan blades of Ti-6Al-4V are targeted for milling, polishing, heat treatment, vibratory finishing, and shot peening. The surface and subsurface residual stress after each process is measured by the X-ray diffraction method. The distribution of the surface and subsurface residual stress is analyzed. The Rational Taylor surface function and cosine decay function are used to fit the characteristic function of the residual stress distribution, and the empirical formula with high fitting accuracy is obtained. The value and distribution of surface and subsurface residual stress vary greatly due to different processing techniques. The reconstructive change of the surface and subsurface residual stress of the blade in each process intuitively shows the change of the residual stress between the processes, which has a high reference significance for the research on the residual stress of the blade processing and the optimization of the entire blade process.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8

Similar content being viewed by others

References

  1. Yao C, Zhang J, Cui M et al (2020) Machining deformation prediction of large fan blades based on loading uneven residual stress. Int J Adv Manuf Technol 107(9/10):4345–4356

    Article  Google Scholar 

  2. Guo M, Jiang X, Ye Y et al (2019) Investigation of redistribution mechanism of residual stress during multi-process milling of thin-walled parts. Int J Adv Manuf Technol 103(1/4):1459–1466

    Article  Google Scholar 

  3. El-Khabeery MM, Fattouh M (1989) Residual stress distribution caused by milling. Int J Mach Tools Manuf 29(3):391–401

    Article  Google Scholar 

  4. Wang J, Zhang D, Wu B et al (2017) Residual stresses analysis in ball end milling of nickel-based superalloy Inconel 718. Mater Res 20(6):1681–1689

    Article  Google Scholar 

  5. Ji C, Sun S, Lin B et al (2018) Effect of cutting parameters on the residual stress distribution generated by pocket milling of 2219 aluminum alloy. Adv Mech Eng 10(12). https://doi.org/10.1177/1687814018813055

    Article  Google Scholar 

  6. Kong X, Ding Z, Xu L et al (2019) Effects of milling parameters on distribution of residual stress during the milling of curved thin-walled parts. EPJ Web Conf 224:5009. https://doi.org/10.1051/epjconf/201922405009

    Article  Google Scholar 

  7. Fuh KH, Wu CF (1995) A residual-stress model for the milling of aluminum alloy (2014–T6). J Mater Process Technol 51(1/4):87–105

    Article  Google Scholar 

  8. Peng FY, Dong Q, Yan R et al (2016) Analytical modeling and experimental validation of residual stress in micro-end-milling. Int J Adv Manuf Technol 87(9/12):3411–3424

    Article  Google Scholar 

  9. Yang D, Liu Z, Ren X et al (2016) Hybrid modeling with finite element and statistical methods for residual stress prediction in peripheral milling of titanium alloy Ti-6Al-4V. Int J Mech Sci 108/109:29–38

    Article  Google Scholar 

  10. Wang J, Zhang D, Wu B et al (2017) Numerical and empirical modelling of machining-induced residual stresses in ball end milling of Inconel 718. Procedia CIRP 58:7–12

    Article  Google Scholar 

  11. Zhou R, Yang W (2019) Correction to: analytical modeling of residual stress in helical end milling of nickel-aluminum bronze. Int J Adv Manuf Technol 100(1/4):1011

    Article  Google Scholar 

  12. Qi H, Xie Z, Hong T et al (2017) CFD modelling of a novel hydrodynamic suspension polishing process for ultra-smooth surface with low residual stress. Powder Technol 317:320–328

    Article  Google Scholar 

  13. Lin X, Wu D, Shan X et al (2018) Flexible CNC polishing process and surface integrity of blades. J Mech Sci Technol 32(6):2735–2746

    Article  Google Scholar 

  14. Wu D, Wang H, Zhang K et al (2019) Research on flexible adaptive CNC polishing process and residual stress of blisk blade. Int J Adv Manuf Technol 103(5/8):2495–2513

    Article  Google Scholar 

  15. Xiao G, Huang Y, Yin J (2017) An integrated polishing method for compressor blade surfaces. Int J Adv Manuf Technol 88(5/8):1723–1733

    Article  Google Scholar 

  16. Yuan F, Liu C, Gu H et al (2019) Effects of mechanical polishing treatments on high cycle fatigue behavior of Ti-6Al-2Sn-4Zr-2Mo alloy. Int J Fatigue 121:55–62

    Article  Google Scholar 

  17. Minguela J, Slawik S, Mücklich F et al (2020) Evolution of microstructure and residual stresses in gradually ground/polished 3Y-TZP. J Eur Ceram Soc 40(4):1582–1591

    Article  Google Scholar 

  18. Sridhar BR, Devananda G, Ramachandra K et al (2003) Effect of machining parameters and heat treatment on the residual stress distribution in titanium alloy IMI-834. J Mater Process Technol 139(1/3):628–634

    Article  Google Scholar 

  19. Bensely A, Venkatesh S, Mohan Lal D et al (2008) Effect of cryogenic treatment on distribution of residual stress in case carburized En 353 steel. Mater Sci Eng A 479(1/2):229–235

    Article  Google Scholar 

  20. Paddea S, Francis JA, Paradowska AM et al (2012) Residual stress distributions in a P91 steel-pipe girth weld before and after post weld heat treatment. Mater Sci Eng A 534:663–672

    Article  Google Scholar 

  21. Dong P, Song S, Zhang J (2014) Analysis of residual stress relief mechanisms in post-weld heat treatment. Int J Press Vessels Pip 122:6–14

    Article  Google Scholar 

  22. Araghchi M, Mansouri H, Vafaei R et al (2017) A novel cryogenic treatment for reduction of residual stresses in 2024 aluminum alloy. Mater Sci Eng A 689:48–52

    Article  Google Scholar 

  23. Zhang Z, Ge P, Zhao GZ (2017) Numerical studies of post weld heat treatment on residual stresses in welded impeller. Int J Press Vessels Pip 153:1–14

    Article  Google Scholar 

  24. Bai Q, Feng H, Si LK et al (2019) A novel stress relaxation modeling for predicting the change of residual stress during annealing heat treatment. Metall Mater Trans A 50(12):5750–5759

    Article  Google Scholar 

  25. Fu Y, Gao H, Wang X et al (2017) Machining the integral impeller and blisk of aero-engines: a review of surface finishing and strengthening technologies. Chin J Mech Eng 30(3):528–543

    Article  Google Scholar 

  26. Kacaras A, Gibmeier J, Zanger F et al (2018) Influence of rotational speed on surface states after stream finishing. Procedia CIRP 71:221–226

    Article  Google Scholar 

  27. Luo S, Zhou L, Nie X et al (2019) The compound process of laser shock peening and vibratory finishing and its effect on fatigue strength of Ti-3.5Mo-6.5Al-1.5Zr-0.25Si titanium alloy. J Alloy Compd 783:828–835

    Article  Google Scholar 

  28. Wong BJ, Majumdar K, Ahluwalia K et al (2019) Effects of high frequency vibratory finishing of aerospace components. J Mech Sci Technol 33(4):1809–1815

    Article  Google Scholar 

  29. Zanger F, Kacaras A, Neuenfeldt P et al (2019) Optimization of the stream finishing process for mechanical surface treatment by numerical and experimental process analysis. CIRP Ann 68(1):373–376

    Article  Google Scholar 

  30. Kim T, Lee JH, Lee H et al (2010) An area-average approach to peening residual stress under multi-impacts using a three-dimensional symmetry-cell finite element model with plastic shots. Mater Des 31(1):50–59

    Article  Google Scholar 

  31. Ghasemi A, Hassani-Gangaraj SM, Mahmoudi AH et al (2016) Shot peening coverage effect on residual stress profile by FE random impact analysis. Surf Eng 32(11):861–870

    Article  Google Scholar 

  32. Mahmoudi AH, Ghasemi A, Farrahi GH et al (2016) A comprehensive experimental and numerical study on redistribution of residual stresses by shot peening. Mater Des 90:478–487

    Article  Google Scholar 

  33. Zhan K, Jiang CH, Ji V (2013) Uniformity of residual stress distribution on the surface of S30432 austenitic stainless steel by different shot peening processes. Mater Lett 99:61–64

    Article  Google Scholar 

  34. Sherafatnia K, Farrahi GH, Mahmoudi AH et al (2016) Experimental measurement and analytical determination of shot peening residual stresses considering friction and real unloading behavior. Mater Sci Eng A 657:309–321

    Article  Google Scholar 

  35. Hayashi M, Okido S, Suzuki H (2020) Residual stress distribution in water jet peened type 304 stainless steel. Quantum Beam Sci 4(2):18. https://doi.org/10.3390/qubs4020018

    Article  Google Scholar 

  36. Lai HH, Cheng HC, Lee CY et al (2020) Effect of shot peening time on δ/γ residual stress profiles of AISI 304 weld. J Mater Process Technol 284:116747. https://doi.org/10.1016/j.jmatprotec.2020.116747

    Article  Google Scholar 

  37. Yao C, Wu D, Ma L et al (2016) Surface integrity evolution and fatigue evaluation after milling mode, shot-peening and polishing mode for TB6 titanium alloy. Appl Surf Sci 387:1257–1264

    Article  Google Scholar 

  38. Tan L, Zhang D, Yao C et al (2017) Evolution and empirical modeling of compressive residual stress profile after milling, polishing and shot peening for TC17 alloy. J Manuf Process 26:155–165

    Article  Google Scholar 

  39. Wu D, Zhang D, Yao C (2018) Effect of turning and surface polishing treatments on surface integrity and fatigue performance of nickel-based alloy GH4169. Metals 8(7):549. https://doi.org/10.3390/met8070549

    Article  Google Scholar 

  40. Sridhar BR, Nafde WG, Padmanabhan KA (1992) Effect of shot peening on the residual stress distribution in two commercial titanium alloys. J Mater Sci 27(21):5783–5788

    Article  Google Scholar 

  41. Zhang J, Yao C, Tan L et al (2021) Shot peening parameters optimization based on residual stress-induced deformation of large fan blades. Thin-Walled Struct 161(1):107467. https://doi.org/10.1016/j.tws.2021.107467

    Article  Google Scholar 

Download references

Acknowledgements

This work was funded by the National Natural Science Foundation of China (Grant Nos. 51875472, 91860206, and 51905440), the National Science and Technology Major Project (Grant No. 2017-VII-0001-0094), the National Key Research and Development Plan in Shaanxi Province of China (Grant No. 2019ZDLGY02-03), and the Natural Science Basic Research Plan in Shaanxi Province of China (Grant No. 2020JQ-186).

Author information

Authors and Affiliations

  1. Key Laboratory of High Performance Manufacturing for Aero Engine, Northwestern Polytechnical University, Ministry of Industry and Information Technology, Xi’an, 710072, People’s Republic of China

    Ji-Yin Zhang, Chang-Feng Yao, Min-Chao Cui, Liang Tan & Yun-Qi Sun

  2. Engineering Research Center of Advanced Manufacturing Technology for Aero Engine, Northwestern Polytechnical University, Ministry of Education, Xi’an, 710072, People’s Republic of China

    Ji-Yin Zhang, Chang-Feng Yao, Min-Chao Cui, Liang Tan & Yun-Qi Sun

Authors
  1. Ji-Yin Zhang
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Chang-Feng Yao
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Min-Chao Cui
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Liang Tan
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Yun-Qi Sun
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Chang-Feng Yao.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Zhang, JY., Yao, CF., Cui, MC. et al. Three-dimensional modeling and reconstructive change of residual stress during machining process of milling, polishing, heat treatment, vibratory finishing, and shot peening of fan blade. Adv. Manuf. 9, 430–445 (2021). https://doi.org/10.1007/s40436-021-00351-4

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s40436-021-00351-4

Keywords

Search

Navigation