Skip to main content
SpringerLink
Log in

Static Analysis of Cutting Inserts in a Smoothing Tool by Simulation

  • Published:
Russian Engineering Research Aims and scope

Abstract

Static analysis of the stress–strain state of a smoothing tool is based on mathematical models. By that means, the tool strength may be assessed. The finite-element method is employed, within the framework of SolidWorks/Simulation software.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.

Similar content being viewed by others

REFERENCES

  1. Mitin, E.V., Sul’din, S.P., and Kalyakulin, S.Yu., Strength calculation of a general-purpose light trailer in the starting and turning modes, Avtom. Prom-st’., 2019, no. 3, pp. 33–36.

  2. Sul’din, S.P., Mitin, E.V., and Kalyakulin, S.Yu., Strength calculation of a general-purpose light trailer loaded with stacked cargo, operating in the starting and turning modes, Avtom. Sovrem. Tekhnol., 2019, vol. 73, no. 4, pp. 169–171.

    Google Scholar 

  3. Grigor’ev, A., Loginova, O., Sul’din, S., et al., Strength analysis of a tank-car boiler construction using SolidWorks Simulation software, SAPR Graf., 2019, no. 1 (267), pp. 55–58.

  4. Kalyakulin, S.Yu., Kuz’min, V.V., Mitin, E.V., et al., Development of a mathematical model of a part based on graphic systems models, Inzh. Tekhnol. Sist., 2019, vol. 29, no. 1, pp. 67–76.

    Google Scholar 

  5. Mitin, E.V., Sul’din, S.P., Grigor’ev, A.V., and Okunev, D.V., Design of helical drills with channels for coolant supply, Stanki Instrum., 2019, no. 1, pp. 25–27.

  6. Mitin, E.V., Sul’din, S.P., Grigor’ev, A.V., and Okunev, D.V., Design of helical drills with channels for coolant supply, Russ. Eng. Res., 2019, vol. 39, no. 6, pp. 520–522.

    Article  Google Scholar 

  7. Mitin, E.V. and Sul’din, S.P., Hob strength in gear cutting, Stanki Instrum., 2018, no. 2, pp. 24–27.

  8. Mitin, E.V. and Suldin, S.P., Hob strength in gear cutting, Russ. Eng. Res., 2018, vol. 38, no. 8, pp. 635–637.

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Ogarev Mordovia State University, Saransk, Russia

    E. V. Mitin & S. P. Sul’din

  2. Evsev’ev Mordovia State Pedagogical Institute, Saransk, Russia

    A. E. Mitina

Authors
  1. E. V. Mitin
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. S. P. Sul’din
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. E. Mitina
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to E. V. Mitin.

Additional information

Translated by B. Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Mitin, E.V., Sul’din, S.P. & Mitina, A.E. Static Analysis of Cutting Inserts in a Smoothing Tool by Simulation. Russ. Engin. Res. 41, 353–356 (2021). https://doi.org/10.3103/S1068798X21040158

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X21040158

Keywords:

Search

Navigation