Abstract
Waste magnesia-carbon bricks (MCB) exhibit great potential for being reutilized as MgO additive for iron ore sintering due to their main composition of high activity magnesia and extra carbon content. In this paper, the combustion characteristics of the carbon component of waste MCB were first studied by thermogravimetric, derivative thermogravimetric and differential scanning calorimetry thermal analysis. The influence of waste MCB utilization as MgO additive on the mineralization of sinter raw materials was also systematically investigated. The main conclusions are shown as below: (1) Compared with anthracite, the carbon component of waste MCB has relatively worse flammability and combustibility, and its combustion heat per unit mass is less; (2) As the MgO content of sinter increases from 2.0 to 3.0 wt%, the advantage of using waste MCB, compared with dolomite, as MgO additive in the crystallinity degree of sinter gradually appears; (3) At the MgO content of 3.0 wt%, the sinter using the combination of waste MCB and dolomite as MgO additive has higher content of calcium ferrite, and the distributions of main mineral compositions and pores are more uniform than the sinter totally using dolomite or waste MCB as MgO additive.
Graphical Abstract
Similar content being viewed by others
References
Du CK, Yang J, Zhao XZ et al (2013) Viscosity and desulfurization behavior of blast furnace slag with high Al2O3 content. J Iron Steel Res 25:19–22
Yang ST, Tan WD, Zhou M, Jiang T, Xue XX (2017) Effects of dolomite on mineral compositions and metallurgical properties of chromium-bearing vanadium–titanium magnetite sinter. Minerals 7:210–215
Wang XL (2014) Ferrous metallurgy (ironmaking part). Metallurgical Industry Press, Beijing
Yadav US, Pandey BD, Das BK, Jena DN (2002) Influence of magnesia on sintering characteristics of iron ore. Ironmak Steelmak 29:91–95
Kasai E, Sakano Y, Kawaguchi T, Nakamura T (2000) Influence of properties of fluxing materials on the flow of melt formed in the sintering process. ISIJ Int 40:857–862
Hsieh LH (2005) Effect of raw material composition on the sintering properties. ISIJ Int 45:551–559
Shen FM, Jiang X, Wu G et al (2006) Proper MgO addition in blast furnace operation. ISIJ Int 46:65–69
Cores A, Babich A, Muñiz M, Ferreira S, Mochon J (2010) The influence of different iron ores mixtures composition on the quality of sinter. ISIJ Int 50:1089–1098
Zhou CJ, Liu QM (2005) The practice for increasing sinter MgO content in Hangang. Sinter Pellet 30:37–40
Ke HB, Zhang YZ, Wang LL, Xing HW (2007) Effect of different contents of MgO on sinter quality. Henan Metall 15:8–10
Li Q, Huang ZC, Jiang T, Yang YB, Li GH (2006) Effect of dolomite and serpentine on sinter quality and microstructure. Iron Steel 41:10–14
Fan XH, Li WQ, Gan M et al (2012) Influence and mechanism of MgO on strength of high basicity sinter. J Cent South Univ (Sci Technol) 43:3325–3330
Zhang J, Bu JL, Wang LR, Wang RL (2013) Phase composition analysis of recycled MgO-C ladle lining materials. Adv Mater Res 750:2236–2239
Benavidez ER, Brandaleze E, Lagorio YS, Gladys A, Martinez T (2015) Thermal and mechanical properties of commercial MgO-C bricks. Rev Mater 20:571–575
Wang GW, Zhang JL, Zuo HB (2014) Study on the combustion characteristics and kinetics of pulverized coal with different particle size. Energy Metall Ind 33:49–53
Essenhigh RH, Misra MK, Shaw SW (1989) Ignition of coal particles: a review. Combust Flame 77:3–30
Deprez N, McLachlan DS (1988) The analysis of the electrical conductivity of graphite conductivity of graphite powders during compaction. J Phys D Appl Phys 21:101–106
Murakami K, Sugawara K, Kawaguchi T (2013) Analysis of combustion rate of various carbon materials for iron ore sintering process. ISIJ Int 53:1580–1587
Ye RQ, Xiang CS, Lin J et al (2013) Coal as an abundant source of graphene quantum dots. Nat Commun. https://doi.org/10.1038/ncomms3943
Dwarapudi S, Ghosh TK, Tathavadkar V et al (2012) Effect of MgO in the form of magnesite on the quality and microstructure of hematite pellets. Int J Miner Process 112:55–62
Sugiyama T, Shirouchi S, Tsuchi O et al (1982) High temperature reduction and softening properties of pellets with magnesite. Trans Iron Steel Inst Jpn 23:153–160
Deng T, Hu CQ (2014) Study on the distribution of MgO in the sinter. Henan Metall 22:8–11
Acknowledgements
The authors gratefully acknowledge the financial support for this work from the National Natural Science Foundation of China (No. 51874214), China Postdoctoral Science Foundation (No. 2020M672425), and Hubei Provincial Natural Science Foundation (No. 2020CFB133).
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
On behalf of all authors, the corresponding author states that there is no conflict of interest.
Additional information
The contributing editor for this article was Yongxiang Yang.
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Li, C., Yan, H., Zhang, W. et al. Fundamental Study on the Re-utilization of Waste Magnesia-Carbon Bricks as MgO Additive for Iron Ore Sintering. J. Sustain. Metall. 7, 597–609 (2021). https://doi.org/10.1007/s40831-021-00366-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40831-021-00366-y