Next Article in Journal
The Effect of LiDAR Sampling Density on DTM Accuracy for Areas with Heavy Forest Cover
Previous Article in Journal
Does Differentiation by Certified Raw Wood Change the Average Price at the Tama Roundwood Market Center in Tokyo, Japan?
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Incidence and Severity of End-Splitting in Plantation-Grown Eucalyptus pellita F. Muell. in North Borneo

1
Institute of Tropical Forestry and Forest Products (INTROP), Universiti Putra Malaysia, UPM Serdang 43400, Selangor, Malaysia
2
Forest Solutions Malaysia Sdn. Bhd., L-70-7 KK Times Square, Off Coastal Highway, Kota Kinabalu 88100, Sabah, Malaysia
3
Faculty of Forestry and Environment, Universiti Putra Malaysia, UPM Serdang 43400, Selangor, Malaysia
4
Forest Industries Research Centre, University of the Sunshine Coast, Sippy Downs, Brisbane, QLD 4557, Australia
5
Meder Consulting, Bracken Ridge, QLD 4017, Australia
*
Authors to whom correspondence should be addressed.
Forests 2021, 12(3), 266; https://doi.org/10.3390/f12030266
Submission received: 25 January 2021 / Revised: 18 February 2021 / Accepted: 20 February 2021 / Published: 25 February 2021
(This article belongs to the Section Wood Science and Forest Products)

Abstract

:
Eucalyptus pellita F. Muell. is currently the predominant tree species deployed for tree plantation establishment in some parts of Borneo, particularly Sabah state, Malaysia. Its low disease susceptibility, good growth and form, and desirable wood properties make E. pellita particularly suitable for plantation development in the wet tropical regions of south-east Asia. In spite the many positive traits, practical field observations indicate that the species is susceptible to end-splitting. There is some anecdotal evidence to suggest a genetic relationship with the incidence of end-split, although these observations were not statistically tested. This study evaluates the occurrence of end-splitting in five-year old plantation E. pellita in Sabah as affected by family and growth attributes. An existing progeny tree breeding trial, involving seeds that originated from Papua New Guinea, China, Vietnam, Australia, Sabah, and Sarawak with 106 families, was used to carry out the split assessment. Logs from the second thinning were cut into 2.2-m-long sections. The end splits were measured three days later; the incidence and severity of splitting were assessed at both the large and small ends of each log by using a designated split scoring system. The study shows that 99% of all log cross sections (per cut surface) experienced signs of splitting, with an average of 2.7 splits per cut surface. Overall, 54% of all splits were classed as ‘Three-Quarter Radial Splits’ while the occurrence of internal splits was negligible. Split severity showed a heritable and significant difference (h2 = 0.24 at p ≤ 0.05) among the family levels. Splitting was also significantly related to growth factors such as tree height and diameter at breast height (DBH). The findings suggest that end-splitting is caused by family–environment interactions. This offers the opportunity to improve the wood resource of E. pellita via breeding strategies.

1. Introduction

Eucalyptus pellita F. Muell., also known as red mahogany, occurs naturally in the tropical regions of north-eastern Queensland, Australia, and the island of New Guinea [1]. It can reach heights of up to 40 m and about 1 m diameter at breast height with a usually straight stem form. It grows in gentle to moderate sloping terrain mixed with other eucalypt species in tall open forests and at the fringes of tropical rainforests. It prefers sand to loam soil types with good drainage at altitudes from sea level to 800 m above sea level with moderate to high rainfall of 900 to 4000 mm annually. It is one of the few Eucalyptus species that is adapted to the wet tropical climate and thus less susceptible to fungal leaf pathogens [2]. This adaptation, together with other positive traits, makes it suitable for plantation establishment in wet tropical regions outside of its natural range.
The recent devastation caused by Ceratocystis vascular wilt disease [3,4] has resulted in almost all Acacia mangium Willd. plantations in the Malaysian state of Sabah being replaced by E. pellita. Since 2012, large-scale E. pellita plantations and tree breeding orchards have been established in Sabah and Sarawak states in the north of the island of Borneo [5]. Up until 2020, Sabah had planted about 36,200 ha (source: company data) with Eucalyptus, with the main species being E. pellita, along with E. grandis W. Hill., E. urophylla S.T. Blake., and eucalypt hybrids. A study by Japarudin et al. [6] showed that Eucalyptus pellita had highly productive growth in Sabah (Mean annual increment (MAI) 27.6 m3 ha−1 year−1) compared to other potential species in a taxa trial. A study revealed that among the three species, namely, E. grandis, E. urophylla, and E. pellita, E. pellita has superior characteristics in both the growth rate and wood properties [7]. Hii et al. [8] and Japarudin et al. [9] studied the properties of E. pellita from Sarawak and Sabah and found that it possesses good properties for solid wood and veneer, consistent with earlier studies [10,11]. Unfortunately, the studies also confirmed the brittle nature of E. pellita and its tendency towards end-split formation. Solid wood recovery of E. pellita was reduced by as much as 50% of the viable log length due to longitudinal propagation of end-splits [9]. There were also anecdotal observations that there could be a provenance effect on end-split incidence, although insufficient samples did not allow for a statistically significant result [9].
Many studies have associated growth stress with an increase in the severity of end-split in logs [12,13]. Beltrame et al. [12] investigated the relationships between the level of longitudinal residual strain (DRL) and the longitudinal growth stresses (TCL) and their effects on the extent of log end-splitting (IRT) of Eucalyptus spp. They discovered that there were significant and positive correlations between DRL/TCL variables and IRT. Thus, it is possible to predict the trend of IRT by performing an evaluation of DRL in the field. Owing to that, this variable has become a reliable tool for the selection of clones less prone to splitting [14]. A high magnitude of longitudinal growth stress has a significant implication in recovery and processing of high-quality timber. Although longitudinal growth stresses are inherent in all trees, their magnitude varies from species to species and also within species. These stresses can cause ring shake and brittle heart in standing trees, end-splitting in logs within a short time span from harvest, severe splitting in timber immediately after sawing, and twisting and cracking in timber during drying [15,16]. Hence, growth stresses have become a major wood quality criterion in the selection of superior genetic material and also in assessing the economic values of logs. Addressing log end-splitting and distortion of timber due to growth stress is necessary if eucalypts are to succeed in solid wood or veneer markets [17]. This study evaluates the incidence and severity of end-splitting and possible effects of family and growth characteristics in E. pellita planted by the Asian Forestry Company Sabah (AFCS) in Northern Sabah.

2. Materials and Methods

2.1. Trial Site

The location of the trial site is shown in Figure 1. It is located at 260 m above sea level, has a mean slope of 24°, and high, unevenly distributed rainfall throughout the year (>3000 mm), with drier summer months from March to October (ca. 200 mm per month) compared to more than 400 mm per month from November to February.
The soil type is classified as a Kumansi (red-yellow podzolic soil) with a clay content of about 50% and good drainage, but some seasonal waterlogging during the rainy season, and an effective rooting depth of 87 cm. Three soil pits were established on the upper, middle, and lower slopes. The soil type was classified by use of Sabah terminology (Figure 2, Table 1). The soil texture was assessed by use of a soil texture triangle to estimate clay, sand, and silt contents by the hand-feel test [18]. Effective rooting depth was measured to the last visible root in the soil profile. Other soil parameters such as soil structure, soil consistency, and stone and root abundance were assessed using The Food and Agriculture Organization (FAO) Guidelines for Soil Description. Other aspects such as waterlogging or drainage characteristics were recorded. Details of the trial site are summarized in Table 1.

2.2. Families and Trial Design

The 106 improved families used in the AFCS progeny trial originate from progeny tree breeding trials in China, Vietnam, and Papua New Guinea. These progeny trials were established with improved material from other breeding programs such as Ingham seedling seed orchard (SSO), Danbulla SSO, and Kairi SSO, and with material from Vietnam ex Bao Bang SSO. The trial also contained material from wild collections of individual mother trees harvested in Queensland, Australia. The two improved bulk seed sources were from breeding programs in Sabah and Sarawak.
The AFCS trial was laid out using a randomized incomplete block design and was planted in May 2015 with nine replications. For every replication, there were 108 families that were planted in 18 blocks with six families in each block. Three trees per family were planted in line plot formation within each block (Table 2). Therefore, there were 27 trees planted for each family (3 trees × 9 replications) or 324 trees (18 blocks × 6 families × 3 trees) planted in one replication, with a total of 2916 trees altogether.

2.3. Height and Diameter Measurements

The trial trees were first measured for height and diameter at breast height (DBH) together with a form assessment once they reached three years of age. After that measurement was taken, the first inferior tree per family in each replication was removed. When the trees were five years old, the second measurement of the height and DBH was carried out, at which stage the trial area was converted to a seed orchard (SSO) by removal of the second inferior tree per family per replication. Trees felled during this stage were denoted as second thinning and were used in this study.

2.4. End-Splitting Assessment

Trees felled during the second thinning operation were used to carry out the split assessment. The number of trees felled and assessed are varied between family as it depends on the suitability of the trees during thinning operation. Out of 2916 trees in the trial design, a total of 486 trees that are still alive and having over bark diameter more than 10 cm were sampled. Immediately after felling, the trees were cut into 1144 pieces of 2.2-m-long billets up to a small end over-bark diameter of 10 cm. Each log was labeled with the treatment number at both ends with the use of a crayon. Seventy-two hours (three days) after felling and cross cutting, the incidence and severity of end-splitting were assessed for both large and small log ends using a modified Split Scoring System developed by the Council for Scientific and Industrial Research, South Africa (Figure 3). Splits were classified according to the radial distance impacted by the split. The scores were determined according to Table 3.
During the field assessment, the number of splits, n, per split category (a–f) was recorded. The total score for each log section was calculated for large and small ends as
Split score = Σ [na(1) + nb(1.5) + nc(2) + ne(1) + nf(2) + Σ d
where
n = the number of splits per split category
a, b, c, d, e, f = split category according to Table 3
Σd = sum of the width of the split (mm) at the outer circumference
value in ( ) = scoring points according to categories of splits in Table 3

2.5. Determination of the Split Sample Size

Prior to the analysis, the required split sample size per family was determined by use of the Yamane formula [19].
n   Yamane   =   N 1   + N ( e 2 )
where
n = split sample number/size
N = population
e = confidence level
The Yamane formula is suitable to determine the sample numbers required for studies with a known population size. All families with a total split sample amount below the 80% confidence level were excluded from the statistical analysis.

2.6. Determination of Narrow Sense Heritability

Narrow sense heritability (h²) for the trait log end-splitting was calculated for open pollinated half-sib families with increased relatedness as follows:
h 2   =   3 σ f 2 σ p 2
with σ p 2 comprising σ f 2 +   σ f r 2 +   σ e 2
where
σ f 2  family component of variance
σ p 2  phenotypic component of variance
σ f r 2  family x replication (block) component of variance
σ e 2  error component of variance

2.7. Statistical Analysis

The statistical analysis incorporated the randomized incomplete block design of the progeny trial, with data organized according to replication, block, plot, and treatment/ family. The Statgraphics Centurion 18 software package (Statgraphics Technologies, Inc., The Plains, VA, USA) and R version 4.0.3 (R Development Core Team, R Foundation for Statistical Computing, Vienna, Austria) were used for data analysis. Analysis of variance (ANOVA) was carried out to determine the effects of family by split and growth by split relationships at the 95% confidence level. Multiple range testing with 95% Tukey’s honestly significant difference (HSD) procedure was used to determine significant differences in splitting between individual families. Regression analysis was conducted to further analyze the relationships between tree height and splits, as well as between DBH and splits. R statistical analysis software was used to calculate narrow-sense heritability estimates (h²) for the trait log end-splitting in E. pellita. For this purpose, the bulk seed sources, comprising numerous unknown families, were excluded from the data set and only individual families were analyzed. Best linear unbiased predictions (BLUP) were applied using R, predicting log end-splitting by family.

3. Results

3.1. Split Type and Occurrence

In this study, E. pellita showed a high tendency towards end-splitting which suggests the wood is brittle. About 99% of all logs showed some signs of splitting on their cross-sectional surface with an average of 2.7 splits per cut surface. Three-Quarter Radial Splits were the most frequently observed split types with a 54% occurrence rate, followed by Pith to Bark Splits, with 35%, and Half Radial Splits, with 11% (Figure 5). It appears that Internal Splits rarely occur in E. pellita and only amounted to 0.02% of all split types observed.

3.2. Family Effects and End-Splitting

Table 4 shows that end-splitting among the families is significantly different (at p ≤ 0.01), which infers that end-splitting in E. pellita is, to some extent, under genetic control. This is further evidenced by the end-splitting score for different families of E. pellita in the AFCS plantation (Figure 6), which shows a near four-fold difference in the incidence of splitting between the families with the most severe splitting and those families with the least. The bar chart is arranged based on the occurrence of end splitting as denoted by different letters according to Tukey’s test.
Table 5 lists five families with high (having split scores of >7.0) and low (having split scores of <2.8) occurrence of end-splitting. In the AFCS progeny trial, there was a significant variation of 78% between the highest and lowest split score. The Sabah 129 family had the highest split occurrence, as well as severity, whereas Queensland 126 had the lowest (Figure 6). Based on these performances, about 3.4% (three families—Sabah 129, PNG 88, and Vietnam 43) in the AFCS breeding population had notably higher split occurrence and severity. In addition, families Queensland 126, Vietnam 41, China 3, Queensland 120, and China 21 all showed a low incidence and severity of end-split. It may be possible that careful selection of second-generation genetic material could select against end-splitting.
The narrow-sense heritability estimate (h²) for the log end-splitting trait in E. pellita within the 106 families within the progeny trial was 0.24, indicating a reasonably high genetic heritability for this trait. The best linear unbiased prediction (BLUP) for log end-splitting in E. pellita predicted split by family with results very similar to those of the actual split assessment, although some of the families changed with regard to the sequence of the severity ranking (Figure 7).

3.3. Growth Effects and End-Splitting

Figure 8 illustrates the relationship between height and the occurrence of end-splitting in E. pellita. Based on the ANOVA (Table 6), tree height was statistically significant (p ≤ 0.01) in relation to log end-splitting. A similar result was obtained for the relationship between DBH and end-splits, but at a lower significance level, i.e., p ≤ 0.05 (Figure 9 and Table 7). Since the growth of a tree or a certain family is dependent on the site conditions, especially soil characteristics, it can be construed that environmental factors in interaction with family genetics contribute significantly to log end-splitting in E. pellita.

4. Discussion

This study has shown that both family and growth characteristics (tree height and DBH) are the main factors related to end-splitting in five-year-old plantation-grown E. pellita. The AFCS progeny trial results revealed a significant and heritable influence of family variation on the end-splitting severity of E. pellita for the 106 families. The buildup and release of growth strain (stress), which leads to wood split, vary based on the genetic makeup of the individual tree and the family it originates from. The narrow-sense heritability of 0.24 suggests that end-splitting is under some degree of genetic control, so strategic genetic selection could be used to breed against high incidence of end-splitting in E. pellita. It is therefore an important criterion that should be incorporated into E. pellita breeding programs. The results of this study are supported by research findings of other fast-growing Eucalyptus species in different countries. For instance, the end-splitting trait in South African E. grandis is moderately heritable, which allows its reduction by genotype selection [20]. A study in Sri Lanka suggested heritability estimates for end-splitting of 0.16 to 0.15 for E. grandis [21]. Higher heritability estimates for end-splitting of 0.31 were reported for E. grandis in Brazil [22]. An assessment of nine-year-old E. dunnii Maiden. plantation trees in Australia reported a heritability of 0.3–0.5 for longitudinal growth strain [23]. These reported heritability estimates indicate that growth stress levels can be genetically altered via selection.
In the South African breeding program for E. grandis, only genotypes with low end-splitting were accepted to form a part of the breeding population [20]. Within the New Zealand Pinus radiata breeding program, prior focus on volume production alone has in some instances led to a decrease in wood properties and overall economic returns [24]. This suggests that the traditional approach to selection of genetic material for breeding purposes based only on phenotypic expression (mainly form and volume) is insufficient and therefore requires additional incorporation of wood property traits [25,26,27].
Economic losses due to end-splitting are not restricted to round log production only but occur at all stages of downstream processing. Maree and Malan [28] estimated the losses due to splitting amounted for up to 10% of the sawn timber production for E. grandis in South Africa whilst Yang [16] reported losses of 6% due to the need to remove the curved edges in the slabs of E. globulus Labill. Similarly, with veneer recovery, assessment of a number of different eucalypts in Australia showed 28% of the veneers were down-graded to low-value D-grade quality due to veneer splits [29], whilst peeling and sawing trials in Sarawak [8] and Sabah [9] states in Malaysia identified end-splits as the greatest source of recovery loss with up to 50% loss of viable log length. A similar result was observed in veneer recovery of New Zealand-grown E. globoidea Blakely., where recovery per log varied from 23.6% to 74.5% with the loss of recovery due to split formation [30]. In China [31], the use of E. urophylla × E. grandis hybrids was able to increase recovery of higher value veneer grades, as well as reduce losses. Yang and Pongracic [32] developed a method to quantify the overall severity of log end-splitting using split indices. They also reported on methods to determine the loss of sawn timber recovery associated with growth stress release by estimating the volume of the curved-edge off-cuts.
This study has also proven that, apart from the family component, growth characteristics such as tree height and DBH play an important role in influencing the end-splitting of E. pellita. In comparison to DBH, tree height exerted a more prominent effect as tall trees commonly exhibit increased split occurrence and higher split severity. On the other hand, although the influence has proven to be statistically moderate, E. pellita with larger DBH does exhibit increased end-splitting. In plantation-grown E. nitens Deane & Maiden., splitting was observed to increase with tree diameter and with increased storage time [33]. In another study, Nascimento et al. [34] revealed that density did not have any notable influence on the end-splitting and surface cracks of E. urophylla logs; instead, the log diameter significantly contributed to the extent of end splits. Due to this unfavorable relation of wood splitting and growth in E. pellita, tree breeders need to carry out genetic selections of high volume and low-splitting genetic material and to exclude high growth strain individuals/families from the breeding program. These findings are in agreement with several reported studies. A study on Acacia auriculiformis Cunn. ex Benth. showed that growth strain (stress) development, which is responsible for wood splits, is dynamic and varies significantly during the development of a tree with increased age and tree height increment [35]. The same study with A. auriculiformis concluded a moderate relationship of DBH and growth strain [35]. For E. nitens plantation-grown trees in Chile, growth strain changes significantly with increased age and tree height and slenderness (height–diameter ratio) [36]. Soil chemical and physical characteristics have a significant impact on growth and therefore on growth strain level development. In relation to this, end-splitting in South African E. grandis logs increases with growth rate, resulting in higher split occurrence for fast-grown trees [37]. Similarly, end-splitting in E. grandis on good-quality sites is increased by about 50% in comparison to low-quality sites in South Africa [20]. For E. pellita and other tree species, growth is an expression of genotype by environment interaction. Good or poor growth of a certain genotype/family is dependent on the site conditions, and therefore growth strain development is partly environmentally controlled. Together with growth, wood property traits have to be improved simultaneously in order to assure the long-term productivity and optimization of higher grade recovery and thus higher economic returns.

5. Conclusions

E. pellita planted in Sabah, North Borneo, has up to 99% occurrence of end-splitting in logs. The main split type was that of ‘Three-Quarter Radial Splits’ followed by ‘Pith to Bark Splits’ and ‘Half Radial Splits’. Internal splits were very rare. Both family and growth characteristics (tree height and DBH) were the main factors associated with end-splitting. Compared to DBH, tree height had a more significant influence on the occurrence of end-splitting. The study has shown that end-splitting is heritable (h2 = 0.24) and is associated with family–growth–environment interactions and is not the result of a single factor. Significant family-by-growth variation exists for end-splitting in E. pellita logs. The reduction of growth stress levels via genetic selection is seen as a crucial element to be incorporated in the E. pellita breeding strategy. Simultaneous improvement of growth and wood property traits is crucial for the long-term productivity and economic returns of E. pellita plantations in North Borneo.

Author Contributions

Conceptualization, R.M. and P.M.T.; Methodology, R.M., M.E., P.M.T. and S.H.L.; Formal Analysis, M.E. and R.M.; Investigation, M.E.; Data Curation, M.E. and R.M.; Writing-Original Draft Preparation, M.E., S.H.L., and A.S.M.R.; Writing-Review & Editing, R.M., S.H.L. and P.M.T.; Supervision, S.H.L., P.M.T., A.S.M.R. and R.M.; Project Administration, P.M.T.; Funding Acquisition, P.M.T., S.H.L. and A.S.M.R. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by the Trans-disciplinary Fundamental Research Grant Scheme (TRGS 2018-1), Reference code: TRGS/1/2018/UPM/01/2/3, from the Ministry of Higher Education, Malaysia.

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

Not applicable.

Acknowledgments

The authors would like to acknowledge the Asian Forestry Company Sabah (AFCS) and the Borneo Forestry Co-operative (www.borneoforestrycoop.com (accessed on 19 January 2021)) for providing the materials and assistance during this experiment, including the design and provision of seedlots for the progeny trial. Funding assistance from the Ministry of Higher Education Malaysia is gratefully acknowledged. Special thanks are extended to Roger Arnold (Stora Enso) and Jeremy Brawner (University of Florida) for valuable discussion and comment.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Brooker, I.; Kleinig, D. Eucalyptus. In An Illustrated Guide to Identification; New Holland Publishers: Wahroonga, Australia, 2012; p. 230. [Google Scholar]
  2. Harwood, C.E.; Alloysius, D.; Pomroy, P.; Robson, K.W.; Haines, M.W. Early growth and survival of Eucalyptus pellita provenances in a range of tropical environments, compared with E. grandis, E. urophylla and Acacia mangium. New For. 1997, 14, 203–219. [Google Scholar] [CrossRef]
  3. Tarigan, M.; Roux, J.; Wingfield, M.J.; Van Wyk, M.; Tjahjono, B. Three new Ceratocystis spp. in the Ceratocystis moniliformis complex from wounds on Acacia mangium and A. crassicarpa. Mycoscience 2010, 51, 53–67. [Google Scholar] [CrossRef] [Green Version]
  4. Brawner, J.T.; Japarudin, Y.; Lapammu, M.; Rauf, R.; Boden, D.; Wingfield, M.J. Evaluating the inheritance of Ceratocystis acaciivora symptom expression in a diverse Acacia mangium breeding population. South. For. 2015, 77, 83–90. [Google Scholar] [CrossRef]
  5. Paridah, M.T.; Zaiton, S.; Hazandy, A.H.; Raja Abdul, A.R.A. Potential of Eucalyptus Plantation in Malaysia; Malaysian Timber Industry Board, Ministry of Plantation Industries and Commodities: Kuala Lumpur, Malaysia, 2017; p. 74.
  6. Japarudin, Y.; Lapammu, M.; Alwi, A.; Warburton, P.; Macdonell, P.; Boden, D.; Brawner, J.T.; Brown, M.; Meder, R. Growth performance of selected taxa as candidate species for productive tree plantations in Borneo. Aust. For. 2020, 38, 29–38. [Google Scholar] [CrossRef]
  7. Prasetyo, A.; Aiso, H.; Ishiguri, F.; Wahyudi, I.; Wijaya, I.P.G.; Ohshima, J.; Yokota, S. Variations on growth characteristics and wood properties of three Eucalyptus species planted for pulpwood in Indonesia. Tropics 2017, 26, 59–69. [Google Scholar] [CrossRef] [Green Version]
  8. Hii, S.Y.; Ha, K.S.; Ngui, M.L.; Ak Penguang, S.; Duju, A.; Teng, X.Y.; Meder, R. Assessment of plantation-grown Eucalyptus pellita in Borneo, Malaysia for solid wood utilisation. Aust. For. 2017, 80, 26–33. [Google Scholar] [CrossRef]
  9. Japarudin, Y.; Meder, R.; Lapammu, M.; Alwi, A.; Chiu, K.-C.; Ghaffariyan, M.; Brown, M. Veneering and sawing performance of plantation grown Eucalyptus pellita, aged 7–23 years, in Borneo Malaysia. Int. Wood Prod. J. 2021, 12. in press. [Google Scholar] [CrossRef]
  10. Atyeo, W.J.; Hopewell, G.P.; McGavin, R.L. Evaluation of Wood Characteristics of Tropical Post-Mid Rotation Plantation Eucalyptus cloeziana and E. pellita: Part (d) Veneer and Plywood Potential. Forest and Wood Products Australia Report PN07.3022-D. 2008, p. 47. Available online: http://www.fwpa.com.au/images/resources/FWPA_PN07.3022_Part%20D.pdf (accessed on 19 January 2021).
  11. Bailleres, H.; Hopewell, G.P.; McGavin, R.L. Evaluation of Wood Characteristics of Tropical Post-Mid Rotation Plantation Eucalyptus cloeziana and E. pellita: Part (c) Wood Quality and Structural Properties. Forest and Wood Products Australia Report PN07.3022-C. 2008, p. 65. Available online: http://www.fwpa.com.au/images/resources/FWPA_PN07.3022_Part%20C_0.pdf (accessed on 19 January 2021).
  12. Naghizadeh, Z.; Wessels, C.B. The effect of water availability on growth strain in Eucalyptus grandis-urophylla trees. For. Ecol. Manag. 2021, 483, 118926. [Google Scholar] [CrossRef]
  13. França, F.J.N.; Franca, T.S.F.; Vidaure, G.B. Effect of growth stress and interlocked grain on splitting of seven different hybrid clones of Eucalyptus grandis×Eucalyptus urophylla wood. Holzforschung 2020. [Google Scholar] [CrossRef]
  14. Beltrame, R.; de Peres, M.L.; Lazarotto, M.; Gatto, D.A.; Schneid, E.; Haselein, C.R. Growth stress and its relationship with end splits in logs of Eucalyptus spp. Sci. For. 2015, 43, 63–74. [Google Scholar]
  15. Malan, F.S. Clonal differences in log end splitting in Eucalyptus grandis in relation to age, parent performance, growth rate and wood density in two even-aged trials in Mpumalanga, South Africa. South. For. 2009, 70, 37–43. [Google Scholar] [CrossRef]
  16. Yang, J.L. The impact of log-end splits and spring on sawn recovery of 32-year-old plantation Eucalyptus globulus Labill. Holz. Roh. Werkst. 2005, 63, 442–448. [Google Scholar] [CrossRef]
  17. Sharma, M.; Walker, J.C.F.; Chauhan, S.S. Eliminating growth-stresses in eucalyptus: A scoping study with E. bosistoana and E. nitens. In Wood is Good; Springer: Singapore, 2017; pp. 47–54. [Google Scholar]
  18. USDA Soil Texturing Field Flow Chart. Available online: www.midwestgeo.com (accessed on 14 October 2020).
  19. Yamane, T. Statistics: An Introductory Analysis, 2nd ed.; Harper and Row: New York, NY, USA, 1967. [Google Scholar]
  20. Malan, F.S. Studies on the Phenotypic Variation in Growth Stress Intensity and Its Association with Tree and Wood Properties of South African Grown Eucalyptus grandis (Hill ex Maiden). Ph.D. Thesis, University of Stellenbosch, Stellenbosch, South Africa, 1984. [Google Scholar]
  21. Bandara, K.M.A.; Arnold, R.J. Genetic variation of growth and log end-splitting in second-generation Eucalyptus grandis in Sri Lanka. Aust. For. 2017, 80, 264–271. [Google Scholar] [CrossRef]
  22. Santos, P.E.T.; Geraldi, I.O.; Garcia, J.N. Estimates of genetic parameters for physical and mechanical properties of wood in Eucalyptus grandis. Sci. For. 2003, 63, 54–64. [Google Scholar]
  23. Murphy, T.N.; Henson, M.; Vanclay, J.K. Growth stress in Eucalyptus dunnii. Aust. For. 2005, 68, 144–149. [Google Scholar] [CrossRef] [Green Version]
  24. Burdon, R.D. Wood properties and genetic improvement of radiata pine. N. Z. J. For. Sci. 2010, 55, 22–27. [Google Scholar]
  25. Ivkovic, M.; Wu, H.X.; Kumar, S. Bio-economic modeling as a method for determining economic weights for optimal multiple-trait tree selection. Silvae Genet. 2010, 59, 77–90. [Google Scholar] [CrossRef] [Green Version]
  26. Wu, H.X.; Ivkovich, M.; Gapare, W.J.; Matheson, A.C.; Baltunis, B.S.; Powell, M.B.; McRae, T.A. Breeding for wood quality and profit in radiata pine: A review of genetic parameters and implication for breeding and deployment. N. Z. J. For. Sci. 2008, 38, 56–87. [Google Scholar]
  27. Rocha, M.F.V.; Veiga, T.R.L.A.; Soares, B.C.D.; Araujo, A.C.C.; Carvalho, A.M.M.; Hein, P.R.G. Do the growing conditions of trees influence the wood properties? Floresta Ambient 2019, 26, e20180353. [Google Scholar] [CrossRef]
  28. Maree, B.; Malan, F.S. Growing for solid hardwood products—A South African experience and perspective. In Proceedings of the Future of Eucalypts for Wood Products, IUFRO Conference, Launceston, Tasmania, Australia, 19–24 March 2000; pp. 319–327. [Google Scholar]
  29. McGavin, R.L.; Bailleres, H.; Lane, F.; Fehrmann, J.; Ozarska, B. Veneer grade analysis of early to mid-rotation plantation Eucalyptus species in Australia. BioResources 2014, 9, 6562–6581. [Google Scholar] [CrossRef] [Green Version]
  30. Guo, F.; Altaner, C.M. Properties of rotary peeled veneer and laminated lumber (LVL) from New Zealand grown Eucalyptus globoidea. N. Z. J. For. Sci. 2018, 48, 3–10. [Google Scholar] [CrossRef] [Green Version]
  31. Peng, Y.; Washusen, R.; Xiang, D.; Lan, J.; Chen, S.; Arnold, R. Grade and value variation in Eucalyptus urophylla x E. grandis veneer due to variation in initial plantation spacings. Aust. For. 2014, 77, 39–50. [Google Scholar] [CrossRef]
  32. Yang, J.L.; Pongracic, S. The Impact of Growth Stresses on Sawn Distortion and Log End-Splitting of 32-Year-Old Plantation Blue Gum; Forest & Wood Products Research & Development Corporation: Melbourne, Australia, 2004; p. 34. Available online: https://www.fwpa.com.au/images/processing/PN03.1312.pdf (accessed on 21 January 2021).
  33. Vega, M.; Hamilton, M.G.; Blackburn, D.P.; McGavin, R.L.; Baillières, H.; Potts, B.M. Influence of site, storage and steaming on Eucalyptus nitens log-end splitting. Ann. For. Sci. 2016, 73, 257–266. [Google Scholar] [CrossRef] [Green Version]
  34. Nascimento, T.M.; Monteiro, T.C.; Baranna, E.E.P. Drying influence on the development of cracks in Eucalyptus logs. BioResources 2019, 14, 220–223. [Google Scholar] [CrossRef]
  35. Aggarwal, P.K.; Chauhan, S.S.; Karmarkar, A. Growth strain in Acacia auriculiformis trees of different age: Their relationship with growth rate and height. J. Inst. Wood Sci. 2013, 17, 212–215. [Google Scholar] [CrossRef]
  36. Biechele, T.; Nutto, L.; Navarete, E. Growth stress in Eucalyptus nitens at different stages of development. In Proceedings of the 51st International Convention of Society of Wood Science and Technology, Conception, Chile, 10–12 November 2008. [Google Scholar]
  37. Malan, F.S.; Hoon, M. Effect of initial spacing and thinning on some wood properties of Eucalyptus grandis. S. Afr. For. J. 1992, 163, 13–20. [Google Scholar]
Figure 1. Location of the trial site at Asian Forestry Company (Sabah) Sdn Bhd (AFCS). Source: Google Earth.
Figure 1. Location of the trial site at Asian Forestry Company (Sabah) Sdn Bhd (AFCS). Source: Google Earth.
Forests 12 00266 g001
Figure 2. Soil profile of the middle slope with Kumansi soil type and silty clay (50% clay) as soil texture.
Figure 2. Soil profile of the middle slope with Kumansi soil type and silty clay (50% clay) as soil texture.
Forests 12 00266 g002
Figure 3. Modified CSIRO split scoring system showing type of splits in Eucalyptus pellita F. Muell. (Note: see Table 3 for Split Scoring Points assigned).
Figure 3. Modified CSIRO split scoring system showing type of splits in Eucalyptus pellita F. Muell. (Note: see Table 3 for Split Scoring Points assigned).
Forests 12 00266 g003
Figure 4. Measurement of split width for splits from pith to bark.
Figure 4. Measurement of split width for splits from pith to bark.
Forests 12 00266 g004
Figure 5. Split types and their occurrence rate (%) for Eucalyptus pellita F. Muell. in AFCS.
Figure 5. Split types and their occurrence rate (%) for Eucalyptus pellita F. Muell. in AFCS.
Forests 12 00266 g005
Figure 6. Mean split scores of E. pellita logs of different families obtained from the AFCS plantation site. (Note: Means followed by the same letters a, b, c, d, e, f, g are not significantly different at p ≤ 0.05 according to Tukey’s test).
Figure 6. Mean split scores of E. pellita logs of different families obtained from the AFCS plantation site. (Note: Means followed by the same letters a, b, c, d, e, f, g are not significantly different at p ≤ 0.05 according to Tukey’s test).
Forests 12 00266 g006
Figure 7. Best linear unbiased prediction (BLUP) for log end-splitting by family in E. pellita.
Figure 7. Best linear unbiased prediction (BLUP) for log end-splitting by family in E. pellita.
Forests 12 00266 g007
Figure 8. Simple regression for log end-splitting in relation to tree height.
Figure 8. Simple regression for log end-splitting in relation to tree height.
Forests 12 00266 g008
Figure 9. Simple regression for log end-splitting in relation to DBH.
Figure 9. Simple regression for log end-splitting in relation to DBH.
Forests 12 00266 g009
Table 1. Site Information.
Table 1. Site Information.
DescriptionData
Type of Trial: Eucalyptus pellita F. Muell. Progeny Trial
Trial Owner:Asian Forestry Company (Sabah) Sdn Bhd (AFCS)
Trial Location:Coupe 7, Block 1 & 2, Kota Marudu District, North Sabah
Latitude—Longitude:6°30′8.82′′ N 117°2′50.38′′ E
Elevation:260 m above sea level
Mean Annual Rainfall:3140 mm
Mean Slope Degree:24°
Soil Type:Kumansi
Soil Texture:Silty Clay (50% Clay)
Drainage:Good with some periodic waterlogging in the rainy season
Effective Rooting Depth:87 cm
Parent Material:Sandstone
Planting Date: May 2015
Assessment Date:May 2020
Trial Age at Assessment:5 years
Spacing:3 m × 3 m
Table 2. Genetic material and trial design used in the AFCS Eucalyptus pellita F. Muell. progeny trial.
Table 2. Genetic material and trial design used in the AFCS Eucalyptus pellita F. Muell. progeny trial.
Origin of Seed MaterialPapua New Guinea, China, Vietnam, Queensland, Sabah, Sarawak
Trial DesignRandomized Incomplete Block
Replications9
No. of blocks per replication18
Total no. of families108
No. of families per block6
Trees per families3
Table 3. Split scoring point assignment.
Table 3. Split scoring point assignment.
DescriptionCategory (Split Type)Scores
A split extending from the pith to half of the log radiusHalf Radial Split
(a)
1
A split extending from the pith to 70% of the log radius Three Quarter Radial Split
(b)
1.5
A split extending from the pith to the outer periphery of the log Full Radius Split
(c)
2
Pith to bark splits can open up at the outer circumference of the log and are measured in width by the use of an electronic caliper (Figure 4).
Score is assessed for every 1 mm of gap ≥ 1 mm
Radial Split
(d)
1 for every one millimeter (1/mm)
Internal splits tangentially connect the radial splits if they reach half the arc-circumferential length or part thereof Internal Split
(e)
1
If the internal split is longer than half of the log radius Internal Split
(f)
2
Table 4. Analysis of variance for the effects of family on log end-splitting.
Table 4. Analysis of variance for the effects of family on log end-splitting.
SourceSum of SquaresdfMean SquareSDF-Ratiop-Value
Between groups1744.638620.28641.5413.860.0000 ***
Within groups5280.3110065.24882
Total (Corr.)7024.941092
*** Significant at p ≤ 0.01.
Table 5. List of families with high (>7.0 score) and low (<2.8 score) occurrence of end-splitting.
Table 5. List of families with high (>7.0 score) and low (<2.8 score) occurrence of end-splitting.
High Occurrence of SplittingLow Occurrence of Splitting
Sabah 129Queensland 126
PNG 88Vietnam 41
Vietnam 43China 3
Vietnam 61Queensland 120
Vietnam 58China 21
Table 6. Analysis of variance between log end-splitting and tree height.
Table 6. Analysis of variance between log end-splitting and tree height.
SourceSum of SquaresdfMean SquareF-ratiop-Value
Between groups783.5771206.52981.80.0000 ***
Within groups1035.892853.63471
Total (Corr)1819.47405
*** Significant at p ≤ 0.01.
Table 7. Analysis of variance between log end-splitting and DBH.
Table 7. Analysis of variance between log end-splitting and DBH.
SourceSum of SquaresdfMean SquareF-Ratiop-Value
Between groups631.9421155.495151.340.0259 **
Within groups1187.532904.09492
Total (Corr)1819.47405
** Significant at p ≤ 0.05.
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Espey, M.; Md. Tahir, P.; Lee, S.H.; Muhammad Roseley, A.S.; Meder, R. Incidence and Severity of End-Splitting in Plantation-Grown Eucalyptus pellita F. Muell. in North Borneo. Forests 2021, 12, 266. https://doi.org/10.3390/f12030266

AMA Style

Espey M, Md. Tahir P, Lee SH, Muhammad Roseley AS, Meder R. Incidence and Severity of End-Splitting in Plantation-Grown Eucalyptus pellita F. Muell. in North Borneo. Forests. 2021; 12(3):266. https://doi.org/10.3390/f12030266

Chicago/Turabian Style

Espey, Manuel, Paridah Md. Tahir, Seng Hua Lee, Adlin Sabrina Muhammad Roseley, and Roger Meder. 2021. "Incidence and Severity of End-Splitting in Plantation-Grown Eucalyptus pellita F. Muell. in North Borneo" Forests 12, no. 3: 266. https://doi.org/10.3390/f12030266

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop