Spectral Efficient Asymmetrically Clipped Hybrid FBMC for Visible Light Communication

Kumar, Sanjeev; Singh, Preeti

doi:https://doi.org/10.1155/2021/8897928

International Journal of Optics

On this page

Abstract Introduction Conclusions Data Availability Conflicts of Interest Acknowledgments References Copyright Related Articles

Special Issue

The Future of Opto-Electronics: Device Architecture, Novel Materials, and Applications

View this Special Issue

Research Article | Open Access

Volume 2021 | Article ID 8897928 | https://doi.org/10.1155/2021/8897928

Spectral Efficient Asymmetrically Clipped Hybrid FBMC for Visible Light Communication

Sanjeev Kumar¹and Preeti Singh¹

Academic Editor: Sulaiman W. Harun

Received10 Sept 2020

Revised03 Jan 2021

Accepted09 Jan 2021

Published23 Jan 2021

Abstract

Filter bank multicarrier (FBMC) modulation has shown sufficient potential for wireless communication. A hybrid optical FBMC technique is proposed to improve the spectral efficiency of a visible light communication (VLC) system. In this technique, a hybrid asymmetrically clipped optical offset quadrature amplitude modulation FBMC (HACO-OQAM-FBMC) modulation technique is used. Asymmetrically clipped optical FBMC (ACO-FBMC) is used for odd subcarriers, and pulse amplitude modulation-discrete multitone (PAM-DMT) is used for the even subcarriers. The proposed hybrid scheme uses an intensity modulation/direct detection (IM/DD) channel. It is shown that there is no interference on odd subcarriers using the proposed method and receiver demodulation is similar to that of ACO-FBMC receiver. However, clipping noise of ACO-FBMC falls on PAM-DMT subcarriers, which can be cancelled at receiver processing after estimation. The analytical performance of the proposed technique is compared using parameters, namely, bit error rate (BER), spectral efficiency, computational complexity, and peak to average power ratio (PAPR). It is found that HACO-OQAM-FBMC is more spectral efficient than ACO-FBMC and other OFDM-based techniques.

1. Introduction

Orthogonal frequency division multiplexing (OFDM) is used extensively in wired and wireless communication systems. Despite its popularity, it possesses some limitations also such as high out-of-band distortion and long cyclic prefix (CP). In previous years, alternative multicarrier modulation techniques have been studied to address OFDM issues. The filter bank multicarrier (FBMC) modulation technique is considered one of the most potential waveforms for next-generation wireless communications due to its robustness against intersymbol interference (ISI) [1].

Visible light communication (VLC) has drawn great attention of researchers due to its unlicensed spectrum, no health hazards, and no electromagnetic interference [2]. In radio frequency (RF) communications, FBMC has been considered as a strong competitor of OFDM [3, 4]. But, for the VLC system, which uses an intensity modulation/direct detection (IM/DD) channel, the signal should be real and unipolar [5–7]. Moreover, the average power of RF communication is the mean square value of the signal, but the average power of VLC is the mean value of the signal. A lower average power is usually preferred for RF communication, but VLC has a predefined average intensity according to the dimming target, which is not an objective function but a constraint [8, 9]. So, FBMC techniques as implemented in RF communications straightforward cannot be used in the VLC system.

The modulation techniques mostly used in the VLC system are asymmetrical clipped optical OFDM (ACO-OFDM) and DC biased optical OFDM (DCO-OFDM). Spectral efficiency of ACO-OFDM is low because only odd subcarriers are used and even subcarriers are neglected to meet the requirement of the VLC system [10]. To improve the spectral efficiency of the VLC system mostly proposed techniques in literature are based on OFDM. Asymmetrically clipped DC biased OFDM (ADO-OFDM) to improve the spectral efficiency of ACO-OFDM is proposed in [11]. But, it uses DC bias for even subcarriers which is a power inefficient method. In [12], the author proposed enhanced hybrid asymmetrically clipped OFDM (EHACO-OFDM) which increases spectral efficiency but has more complexity. Till date, there is no work reported in the literature which discusses the assessment of the hybrid FBMC modulation technique for VLC based on the IM/DD channel.

In this paper, the authors proposed hybrid asymmetrically clipped optical offset quadrature amplitude modulation FBMC (HACO-OQAM-FBMC) in which ACO-FBMC is used for the odd subcarriers and PAM-DMT is used for the even subcarriers. The clipping noise of ACO-FBMC falls only on even subcarriers. The receiver of HACO-OQAM-FBMC consists of four signals: the wanted ACO-FBMC signal, clipping noise from ACO-FBMC, PAM-DMT signal, and noise added in the channel. The clipping noise of ACO-FBMC can be accurately separated from PAM-DMT after estimation before demodulation.

The authors’ contributions can be summarized as follows:(1)The system model is proposed for the HACO-OQAM-FBMC modulation technique(2)Scaling techniques are used for the proposed FBMC-based model for the VLC system(3)The performance analysis is carried out using spectral efficiency, bit error rate (BER), computational complexity, and peak to average power ratio (PAPR) for the FBMC-based VLC system(4)Non-DC bias methods are used for the proposed model of the VLC system(5)The performance of ACO-OFDM, DCO-OFDM, ADO-OFDM, EHACO-OFDM, ACO-FBMC, DCO-FBMC, and HACO-OQAM-FBMC modulation techniques has been compared

The content of this paper is systematized as follows. Section 2 gives the system model for the HACO-OQAM-FBMC modulation technique. Performance analysis of the proposed system models is performed in Section 3 using parameters, probability density function, bit error probability, peak to average power ratio, computational complexity, spectral efficiency, and power spectral density. The conclusion is presented in Section 4.

2. Proposed Modulation Techniques System Model

The system model consists of a transmitter and receiver functional diagram for the VLC system. Figure 1 shows the functional diagram of the transmitter and receiver section of the HACO-OQAM-FBMC modulation technique.

In the transmitter section of HACO-OQAM-FBMC, the offset quadrature amplitude modulation (OQAM) is used for signal mapping. Hermitian symmetry is used to fit the signal into VLC system requirements. Odd subcarriers are modulated using an ACO-FBMC modulator, and a PAM-DMT modulator is used for even subcarriers. An optical modulator is employed to convert an electrical signal to optical signal. In the receiver section of HACO-OQAM-FBMC, an optical demodulator is used to convert an optical signal back to an electrical signal. For extraction of even and odd subcarriers, ACO-FBMC and PAM-DMT demodulators are used. The equalizer is used to remove the distortion, and finally, the signal is extracted using a decoder. The signal analysis of the HACO-OQAM-FBMC transmitter and receiver is given in the next section.

2.1. Signal Analysis of the HACO-OQAM-FBMC Transmitter

The data subcarriers are given by . The ACO-FBMC consists of odd subcarriers , and PAM-DMT consists of even subcarriers . The even and odd subcarriers are sent to the PAM-DMT and ACO-FBMC modulators which consist of IFFT and clipping of the signal. The transmitted ACO-FBMC signal is represented by

Similarly, the transmitted signal of PAM-DMT is given bywhere and are the clipping noise of ACO-FBMC and PAM-DMT [13]. Using equations (1) and (2), the transmitted signal of HACO-OQAM-FBMC is given by

Upper-case letters are used to represent frequency-domain signals, and lower-case letters are used to represent time-domain signals.

2.1.1. ACO-FBMC Modulator

The OQAM modulator output shown in Figure 1 consists of a real and imaginary signal. Upsampling is performed before prototype filter to increase the sampling rate. A PHYDYAS protype filter is used in the proposed method. After IFFT execution, clipping is required to fulfil optical modulator constraints. The block diagram of the ACO-FBMC modulator is shown in Figure 2.

The PHYDYAS prototype filter [14] is given by

The coefficients depend on the overlapping factor , and the procedure for calculation is given in [15]. For example, when the value of the overlapping factor , the coefficients are given by

Orthogonal: . Localization: . Joint Localization: .

2.2. Signal Analysis of the HACO-OQAM-FBMC Receiver

The received signal for HACO-OQAM-FBMC is given bywhere and are the additive white Gaussian noise (AWGN) of the even and odd subcarriers. A flat channel is assumed for one receiver. After applying FFT to equation (6), the signal is given by

The clipping noise and AWGN noise are removed using ACO-FBMC and PAM-DMT demodulators. The decoded signal is given by

2.2.1. ACO-FBMC and PAM-DMT Signal Detection

The optical demodulator output, as shown in Figure 1, consist of ACO-FBMC, PAM-DMT, AWGN noise, and clipping noise. The received signal from optical demodulator is converted into frequency domain using FFT. After that, the ACO-FBMC signal is detected. To recover the PAM-DMT signal, we have to use the clipping noise estimation technique, as shown in Figure 3. In this technique, for proper detection and scaling, odd subcarriers are multiplied by 2 because power of the M-QAM symbols reduced by half due to clipping operation [16, 17]. Subtraction of estimated clipping noise which falls on PAM-DMT (even) subcarriers from received ACO-FBMC symbols will give PAM-DMT symbols.

3. Performance Analysis of HACO-OQAM-FBMC

The performance analysis is carried out using probability density function, bit error rate, spectral efficiency, computational complexity, peak to average power ratio, and power spectral density.

3.1. Probability Density Function (PDF) of HACO-OQAM-FBMC

The PDF of HACO-OQAM-FBMC can be calculated by convolving the PDF of ACO-FBMC and PDF of PAM-DMT. The PDF of ACO-FBMC is given by [18, 19]

The PDF of PAM-DMT given by [18, 20]

The PDF of HACO-OQAM-FBMC can be calculated using convolution of equations (9) and (10).

Substituting equations (9) and (10) in equation (11) giveswhere is the variance of the signal and is given by . Using identity [21, 22],

The optical power of HACO-OQAM-FBMC is given by

The electrical power of HACO-OQAM-FBMC is given by

Equations (14) and (15) have no closed-form solution. Therefore, they are calculated using a numerical process.

The probability density function of HACO-OQAM-FBMC is given in Figure 4. It consists of both theoretical and simulated PDF and shows similar performance. The PDF curve shows that the proposed technique is power efficient.

3.2. Bit Error Probability (BEP) of HACO-OQAM-FBMC

The bit error probability of HACO-OQAM-FBMC is given by [23]where is the constellation size and is the average signal to noise ratio (SNR)/symbol.

Figure 5 shows the bit error rate (BER) performance of the HACO-OQAM-FBMC modulation technique. The FBMC overlapping factor (k = 4) is used for simulation. The theoretical and simulation results show almost similar performance.

As shown in Figure 6, the performance of HACO-OQAM-FBMC shows 2 dB degradation when compared with ACO-OFDM because only half of the power is allocated to odd subcarriers (ACO) in HACO-OQAM-FBMC. In reality, the performance of the proposed scheme is better when compared with ACO-OFDM because the OFDM performance is degraded due to the use of cyclic prefix (CP) [24]. The BER performance of the proposed technique is better than that of DCO-OFDM and ADO-OFDM because no DC bias is used, and hence, it is power efficient.

Analysis of Figure 7 shows that there is a 3 dB penalty for HACO-OQAM-FBMC as compared to ACO-FBMC, but actually both have similar performance because half power of HACO-OQAM-FBMC is contained by even subcarriers (PAM-DMT). The BER performance of the proposed technique is power efficient as compared to that of DCO-FBMC and EHACO-OFDM because no DC bias is used in the proposed technique.

3.3. Peak to Average Power Ratio (PAPR) of HACO-OQAM-FBMC

The PAPR of HACO-OQAM-FBMC is given by

The PAPR of ACO-OFDM, ACO-FBMC, DCO-OFDM, EHACO-OFDM, ADO-OFDM, DCO-OFDM, and HACO-OQAM-FBMC is given in Figure 8. ACO-OFDM has the best PAPR as compared to other techniques. The proposed method HACO-OQAM-FBMC PAPR can be reduced using optimization algorithms. DCO-FBMC has the worst PAPR as compared to other techniques because of DC bias and the FBMC modulation technique.

3.4. Computational Complexity of HACO-OQAM-FBMC

The computational complexity of HACO-OQAM-FBMC is given bywhere is the number of real multiplications for HACO-OQAM-FBMC. is the constellation size, is the number of subcarriers, and is the overlapping factor.where is the number of real additions for HACO-OQAM-FBMC.

The computational complexity of HACO-OQAM-FBMC is given in Figures 9 and 10. The computational complexity of ACO-OFDM is the lowest as compared to other techniques because of the no-DC bias technique and use of OFDM. OFDM has low computational complexity than FBMC [25]. HACO-OQAM-FBMC technique computational complexity is the highest among other techniques because extra processing is required for PAM-DMT signals.

3.5. Spectral Efficiency (SE) of HACO-OQAM-FBMC

The spectral efficiency of HACO-OQAM-FBMC can be calculated from [4]where is the coding rate of channel, , and is the time-frequency efficiency.

The spectral efficiency of ACO-OFDM, DCO-OFDM, ACO-FBMC, DCO-FBMC, EHACO-OFDM, and HACO-OQAM-FBMC is given in Figure 11. The spectral efficiency of HACO-OQAM-FBMC is higher than that of other modulation techniques and almost similar to that of DCO-FBMC because DCO-FBMC does not use Hermitian symmetry and, hence, has more subcarriers for data communication. All other modulation techniques have low spectral efficiency as compared to the proposed method because they are OFDM-based techniques which have low spectral efficiency as compared to FBMC [25].

3.6. Power Spectral Density (PSD) of HACO-OQAM-FBMC

The power spectral density of HACO-OQAM-FBMC is shown in Figure 12. PSD of ACO-FBMC, DCO-FBMC, and HACO-OQAM-FBMC is the same because the same prototype filter is used. The PSD of the proposed technique is better than that of the OFDM-based technique because FBMC has low out-of-band distortion as compared to OFDM.

4. Conclusions

This research work proposes Hybrid FBMC schemes for visible light communication based on an intensity modulation/direct detection (IM/DD) channel. In hybrid asymmetrically clipped DC biased optical FBMC (HACO-OQAM-FBMC), ACO-FBMC is used for the odd subcarriers and for even subcarriers, PAM-DMT is used. The PAPR of the proposed scheme is 0.96 dB more than ACO-FBMC because of hybridization. The spectral efficiency of HACO-OQAM-FBMC is higher than that of ACO-OFDM, DCO-OFDM, ACO-FBMC, and EHACO-OFDM due to use of even subcarriers and the FBMC multicarrier modulation technique. The computational complexity of HACO-OQAM-FBMC is higher because extra processing is required for even subcarriers. It is shown that there is no interference on odd subcarriers because PAM-DMT and receiver demodulation is achieved using the clipping estimation technique. Future directions can be reducing computational complexity and PAPR of HACO-OQAM-FBMC.

Data Availability

The data used to support the findings of this study in the manuscript are available from the corresponding author upon request.

Conflicts of Interest

The authors declare that they have no conflicts of interest.

Acknowledgments

The authors gratefully acknowledge the support of Council of Scientific and Industrial Research (CSIR), New Delhi, under the Senior Research Fellowship grant 09/135/(0798)/18-EMR-I.

References

R. Nissel, S. Schwarz, and M. Rupp, “Filter bank multicarrier modulation schemes for future mobile communications,” IEEE Journal on Selected Areas in Communications, vol. 35, no. 8, pp. 1768–1782, 2017.
View at: Publisher Site | Google Scholar
S. Kumar and P. Singh, “A comprehensive survey of visible light communication: potential and challenges,” Wireless Personal Communications, vol. 109, no. 2, pp. 1357–1375, 2019.
View at: Publisher Site | Google Scholar
X. Zhang, C. Zhang, M. Zhu et al., “SSB pruned DFT-spread FBMC signal with low PAPR in direct-detection PONs,” IEEE Photonics Journal, vol. 12, no. 3, 2020.
View at: Publisher Site | Google Scholar
Y. Liu, X. Chen, Z. Zhong et al., “Waveform design for 5G networks: analysis and comparison,” IEEE Access, vol. 5, pp. 19282–19292, 2017.
View at: Publisher Site | Google Scholar
S. Kumar and P. Singh, “Filter bank multicarrier modulation schemes for visible light communication,” Wireless Personal Communications, vol. 113, no. 4, pp. 2709–2722, 2020.
View at: Publisher Site | Google Scholar
T. C. Bui, S. Kiravittaya, K. Sripimanwat et al., “A comprehensive lighting configuration for efficient indoor visible light communication networks,” International Journal of Optics, vol. 14, 2016.
View at: Google Scholar
M. A. Al-Jarrah, A. Al-Dweik, K.-H. Park, and M.-S. Alouini, “Amplitude-coherent detection for optical wireless communications: opportunities and limitations,” IEEE Open Journal of the Communications Society, vol. 1, pp. 550–562, 2020.
View at: Publisher Site | Google Scholar
J.-Y. Wang, C. Liu, J.-B. Wang, Y. Wu, M. Lin, and J. Cheng, “Physical-layer security for indoor visible light communications: secrecy capacity analysis,” IEEE Transactions on Communications, vol. 66, no. 12, pp. 6423–6436, 2018.
View at: Publisher Site | Google Scholar
J. Y. Wang, Q. L. Li, J. X. Zhu, and Y. Wang, “Impact of receiver’s tilted angle on channel capacity in VLCs,” Electronics Letters, vol. 53, no. 6, pp. 421–423, 2017.
View at: Publisher Site | Google Scholar
J. Armstrong and B. Schmidt, “Comparison of asymmetrically clipped optical OFDM and DC-biased optical OFDM in AWGN,” IEEE Communications Letters, vol. 12, no. 5, pp. 343–345, 2008.
View at: Publisher Site | Google Scholar
X. Zhang, Y. F. Zhou, Y. P. Yu et al., “Comparison and analysis of DCO-OFDM, ACO-OFDM and ADO-OFDM in IM/DD systems,” Applied Mechanics and Materials, vol. 701, pp. 1059–1062, 2015.
View at: Google Scholar
R. Guan, N. Huang, J. Y. Wang et al., “Enhanced hybrid asymmetrically clipped orthogonal frequency division multiplexing for optical wireless communications,” Optical Engineering, vol. 55, no. 5, 2016.
View at: Publisher Site | Google Scholar
S. Dimitrov, S. Sinanovic, and H. Haas, “Signal shaping and modulation for optical wireless communication,” Journal of Lightwave Technology, vol. 30, no. 9, pp. 1319–1328, 2012.
View at: Publisher Site | Google Scholar
M. G. Bellanger, “Specification and design of a prototype filter for filter bank based multicarrier transmission,” IEEE, vol. 4, pp. 2417–2420, 2001.
View at: Google Scholar
S. Mirabbasi and K. Martin, “Design of prototype filter for near-perfect-reconstruction overlapped complex-modulated transmultiplexers,” IEEE, vol. 1, 2002.
View at: Google Scholar
J. Yang and Y. Chen, “Indoor localization using improved rss-based lateration methods,” IEEE, vol. 1, 2009.
View at: Google Scholar
J. Armstrong and A. J. Lowery, “Power efficient optical OFDM,” Electronics Letters, vol. 42, no. 6, pp. 370–372, 2006.
View at: Publisher Site | Google Scholar
L. Chen, B. Krongold, and J. Evans, “Performance analysis for optical OFDM transmission in short-range IM/DD systems,” Journal of Lightwave Technology, vol. 30, no. 7, pp. 974–983, 2012.
View at: Publisher Site | Google Scholar
D. J. Barros, S. K. Wilson, and J. M. Khan, “Comparison of orthogonal frequency-division multiplexing and pulse-amplitude modulation in indoor optical wireless links,” IEEE Transactions on Communications, vol. 60, no. 1, pp. 153–163, 2011.
View at: Google Scholar
X. Li, R. Mardling, and J. Armstrong, “Channel capacity of IM/DD optical communication systems and of ACO-OFDM,” IEEE, vol. 60, pp. 2128–2133, 2007.
View at: Google Scholar
I. S. Gradshteyn and I. M. Ryzhik, “Table of integrals, series, and products,” 2000.
View at: Google Scholar
B. Ranjha and M. Kavehrad, “Hybrid asymmetrically clipped OFDM-based IM/DD optical wireless system,” Journal of Optical Communications and Networking, vol. 6, no. 4, pp. 387–396, 2014.
View at: Publisher Site | Google Scholar
J. G. Proakis and M. Salehi, “Digital communications,” 2014.
View at: Google Scholar
B. Muquet, Z. Zhengdao Wang, G. B. Giannakis et al., “Cyclic prefixing or zero padding for wireless multicarrier transmissions?” IEEE Transactions on Communications, vol. 50, no. 12, pp. 2136–2148, 2002.
View at: Publisher Site | Google Scholar
B. de Courville, “OFDM versus filter bank multicarrier,” IEEE Signal Processing Magazine, vol. 28, no. 3, pp. 92–112, 2011.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2021 Sanjeev Kumar and Preeti Singh. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

801

Downloads

865

Citations