Karst Aquifer Water Inflow into Tunnels: An Analytical Solution

Jiang, Chong; Han, Haixia; Xie, Hansong; Liu, Jing; Chen, Zhao; Chen, Huawei

doi:https://doi.org/10.1155/2021/6672878

Geofluids

On this page

Abstract Introduction Discussion Conclusion Data Availability Conflicts of Interest Acknowledgments References Copyright Related Articles

Special Issue

Thermal-Hydraulic-Mechanical (THM) Coupling Behaviour of Fractured Rock Masses

View this Special Issue

Research Article | Open Access

Volume 2021 | Article ID 6672878 | https://doi.org/10.1155/2021/6672878

Karst Aquifer Water Inflow into Tunnels: An Analytical Solution

Chong Jiang,¹Haixia Han,¹Hansong Xie,¹Jing Liu,¹Zhao Chen,²and Huawei Chen²

Academic Editor: Yanlin Zhao

Received18 Nov 2020

Revised29 Dec 2020

Accepted31 Dec 2020

Published15 Jan 2021

Abstract

This study gives two new analytical solutions to the tunnel by high-pressure water in the cavern. Firstly, it deals with the analytical solution for the seepage inflow in unsupported karst aquifer tunnels considering the boundary condition. Secondly, it focuses on the study of the seepage force and gives the reduction coefficient of lining water pressure. A comparison of the analytical solution and the finite element software shows a curve relationship as the relevant permeability coefficient increases. The results show that the analytical solution and numerical solution are consistent. As increases, decreases gradually. increases as increases or the grouting circle and initial support become thinner or the secondary lining becomes thicker. In summary, the analytical solution of can be used to predict the seepage inflow and the seepage force of the actual engineering.

1. Introduction

There are two types of karst aquifer tunnels: sealed and drained [1]. When designing the sealed tunnels, the lining withstands full hydrostatic pressure and earth pressure [2]. However, the seepage inflow and the head pressure of the lining structure need to be taken into account in the design of the tunnels. Therefore, one of the safety issues is to estimate the seepage inflow and the head pressure of the lining structure acting on the lining.

Early researchers have investigated the problems of deep underwater tunnels and given some solutions to these problems, but they have not been applied to actual engineering [3–5]. Some researchers solved the analytical solution for the groundwater inflow based on the theory of hydraulics and image method [6–9]. Park et al. [10] carefully studied the two boundary conditions around the circumference of the underwater tunnel and deduced two analytical solutions for the groundwater inflow into a tunnel. A seepage filed analytical solution for a lined tunnel was derived, but they only considered one layer of linings [11, 12]. Two types of filled karst caves, with water and with water-mud mixture, in front of the tunnel face are studied to estimate the required thickness of the supporting rock stratum in order to prevent water and mud inrush under earthquake action [13]. Zhang [14], Zheng [15], Kong [16], Shin et al. [17], and Cao et al. [18] derived the analytical solution of water pressure acting on the lining or rock tunnels. Zhang et al. [19] suggested a new set of analytical solutions for predicting the effect of grouting on ground and shield tunnel behavior as a consequence of steady water inflow into a tunnel in saturated clay based on relative permeability of the tunnel lining and grouting material to the surrounding soil. Huang et al. [20] and Perrochet and Dematters [21] established and calculated numerical models to verify theoretical calculations and predict transient discharge flow into a tunnel drilled at various speeds through a heterogeneous formation. Based on a theoretical method for laminar and turbulent flow, Joo and Shin [22] investigated the relationship between water pressure and inflow rate in underwater tunnels and buried pipes. Li et al. [11]. Based on the image method and theory of seepage mechanics, the analytical solution for the steady seepage field of twin-parallel tunnels in the semi-infinite plane was derived and was compared and verified with the numerical solution [23, 24]. A new analytical solution for the karst tunnel was given by Jiang et al. [25] based on mirror image and inversion mapping. Considering the parameters, Xie et al. [26] solved the analytical solution for the karst tunnel based on conformal mapping, but they only considered one of the tunnel boundaries. Park et al. [27] showed the analytical solutions for the seepage force acting on the lining in a drained circular tunnel under the steady-state groundwater flow condition. And some scholars have studied the shear and fracture properties of the surrounding rock [28–31].

Various methods have been developed to estimate the groundwater inflow for deep underwater tunnels. However, there are few analytical solutions for the seepage force of karst aquifer tunnels. This study consists of two parts. First, it deals with the analytical solution for the seepage inflow in the karst aquifer tunnel considering the boundary conditions. And the seepage inflow of unsupported tunnels and supported tunnels is discussed separately. The second part focuses on the study of the karst aquifer tunnel lining structure and gives the analytical solution of the seepage force. And a parameter of the lining water pressure is proposed. The numerical analysis and analytical solution are compared to investigate the effect of different parameters.

2. Analytical Solution of the Tunnel Seepage Field

2.1. Assumption

The basic assumptions of this paper are as follows: (1)The tunnel and the cavern have large depths, and the tunnel is infinitely long, so the working surface is a two-dimensional infinite plane, and the gravity is not considered(2)The surrounding rock is an isotropic and continuous medium(3)The seepage of karst water into the tunnel conforms to Darcy’s law, and the water pressure in the cavern is equal everywhere

2.2. Conformal Mapping

The center of the tunnel is used as an origin in the Cartesian coordinate system, with the horizontal direction represented by the -axis and the vertical direction represented by the -axis, as shown in Figure 1(a). and are radii of the tunnel and the cavern, respectively. The center distance between the tunnel and the cavern is . The tunnel and the cavern in the -plane are mapped onto two concentric circles of radii and 1, in the -plane by the analytic function (Figure 1(b)) [26].

The analytic function of mapping is where and are parameters defined as

By considering the boundary conditions and the Laplace equation in the -plane, the solution for the total head on a circle with radius can be expressed as where , is the water pressure, is the unit weight of water, and is the elevation head. , , , , , and are constants to be determined from the boundary conditions at the tunnel and the cavern circumference. is the natural number, and is the angle between and -axis in the -plane.

2.3. The Boundary Condition

The boundary condition of the cavern circumference is .

The boundary condition of the tunnel circumference is , so .

By considering in the -plane, the elevation head around the tunnel circumference can be expressed as so,

The seepage per unit length of the tunnel length is where is the permeability coefficient of the surrounding rock.

3. The Seepage Force of the Supported Tunnel

The support of the tunnel includes the grouting circle, initial support, and secondary lining, as shown in Figure 2. It is assumed that the pressure heads of support circumferences are equal and constant. And the seepage inflow through the supports is equal to the tunnel seepage inflow.

For the restricted row tunnel, the excavation of the tunnel has an effect on the seepage field of the surrounding rocks, and the seepage force has also changed. The pressure head of any point within the secondary lining can be obtained, according to Darcy’s law and their boundary conditions (, ; , ), and is the radius of any point within the secondary lining in the -plane. where

The water pressure on the outside of the secondary lining can be derived from Equation (10) when , and it approximated to hydrostatic pressure. where is the reduction coefficient of lining water pressure.

The unit seepage force at any point in the secondary lining can be expressed as

After the integration, the seepage force on the outside of the secondary lining is

The pressure head on the outside of the initial support can be obtained, according to its boundary conditions.

And the seepage force on the outside of the initial support is

The pressure head on the outside of the grouting circle can be obtained, according to its boundary conditions.

The seepage force on the outside of the grouting circle is

The seepage force in the surrounding rock is

Before and after the completion of the secondary lining, the difference in the seepage force of the surrounding rock is

From Equation (21), it can be seen that after the completion of the secondary lining, the seepage force of the surrounding rock increases, which means that the direction of the force exerted by the secondary lining on the surrounding rock is away from the direction of the tunnel center.

Then, the tunnel inflow and the seepage force on the outside of the secondary lining can be rewritten as

4. Verification and Discussion

The seepage inflow and the seepage force are important factors reflecting the safety of tunnels in karst areas. It is very important to verify their correctness. The karst water inflow and seepage force are related to according to Equations (22) and (23). So should be verified first. The characteristic parameter values for verification are shown in Table 1. The model of is established with FLAC3D. When , , , , and , the numerical simulation tunnel model consists of 186240 elements, as shown in Figure 3. The pore water pressure at the four points is as follows: 1 (36.25, -2, 50), 2 (41.75, -2, 44.5), 3 (47.25, -2, 50), and 4 (41.75, -2, 55.5), as shown in Figure 4.

4.1. The Effect of the Grouting Circle and Surrounding Rock

The influence of the grouting circle and surrounding rock on is described in Figure 5. It can be seen from Figures 5(a) and 5(b) that is increased as the permeability coefficient of the grouting circle increases, regardless of the analytical solution and numerical solution. increases remarkably when . That is to say, can be reduced efficiently by decreasing the permeability of the grouting circle when . In addition, the numerical solution for at point 3 is 97% of the analytical solution. It can be seen from Figure 5(a) that when , the difference between of different decreases gradually. When , the difference between of different increases gradually. It shows that the effect of on decreases gradually as increases. It means that the seepage inflow and pressure head acting on the outside of the secondary lining without grouting are greater than those with grouting, which indicates that grouting can effectively control the karst inflow to the tunnel. In summary, the analytical solution and the numerical solution are relatively matched. The smaller the permeability coefficient of the grouting circle, the closer the analytic and numerical simulation solutions will be, and the better the match will be.

(a)

(b)

(c)

(d)

Other parameters remained unchanged, and the center distance between the tunnel and the cavern increased from 16.5 m to 20.5 m. Figure 5(c) shows the relationship between and the center distance. The figure shows that decreases as increases. In order to make the tunnel lining bear less water pressure, the pressure head, seepage inflow, and seepage force should be smaller; that is, is smaller. Therefore, considering the economic benefits and feasibility study, the tunnel should be designed away from the cavern.

Figure 5(d) illustrates the relationship between and the thickness of the grouting circle. The slope of decreases gradually, and the influence of on gradually decreases. tends to be stable when gradually approaches . Therefore, when applying on practical projects, the grouting depth should be appropriately increased during grouting to reduce the water inflow and pressure head acting on the outside of the secondary lining; that is, is smaller. In addition, the simulation results show that decreases linearly with the increase of , which is consistent with the analytical solution, reflecting that the conformal mapping method in this paper is feasible.

4.2. The Effect of the Initial Support and Secondary Lining

Figures 6(a) and 6(b) illustrate the relationship between and . It can be seen that the slope of gradually decreases with the increase of . When , the change of with is obvious. Therefore, in the actual project, the thickness of the initial support should be increased to reduce the seepage inflow of the tunnel and pressure head on the outside of the secondary lining. When , has little effect on , which indicates that the influence of the seepage inflow and pressure head on the outside of the secondary lining is small. Therefore, increasing cannot effectively control the inflow of karst water, and it increases the construction cost. And it is not advisable to increase indefinitely to resist water pressure.

(a)

(b)

(c)

(d)

Figure 6(c) compares between the analytical solution and the simulation solutions, considering the relative permeability of the secondary lining to the initial support. The analytical solution is much larger than the numerical solution for at locations. The analysis is based on an infinite plane, but the boundaries of numerical simulation are limited. As shown in Figure 6, as the relative permeability increases, the rate of the decrease slows. As the permeability of the initial support decreases, the gap between the analytical and numerical solutions gradually decreases. When the relative permeability is greater than 10, gradually stabilizes. In addition, the numerical solution for at point 3 is 97% of the analytical solution. That is to say, the analytical solution of can be used to predict the seepage inflow and the seepage force of the actual engineering.

The influence of the thickness of the secondary lining on is shown in Figure 6(d). When , reaches stability when , while when , reaches stability when . It is stated that when is a certain value, increasing will increase the construction cost and fail to reduce the water inflow and pressure head. Therefore, it is unreasonable to increase the infinitely for tunnel seepage safety. Considering the economic benefits and seepage safety of karst aquifer tunnels during construction, and should be appropriately reduced. Results from the finite difference software show that the increase of with tends to be stable at , which is consistent with the analytical solution.

4.3. The Effect of the Cavern

Figure 7 shows the relationship between and . For various radii of the cave, the reduction coefficients of lining water pressure are almost coincident. The tendencies of the analytical solution and the simulation solutions are consistent, but they differ in numerical values. The analytical solution is slightly larger than the numerical solution for at point 3. As shown in Figure 7, increases linearly with the increase of ; in addition, the numerical solution for at point 3 is 95% of the analytical solution. In summary, the analytical solution of can be used to predict the seepage inflow and the seepage force of the actual engineering.

(a)

(b)

5. Conclusion

This paper derived analytical solutions of the seepage inflow in the unsupported tunnel and lining seepage force in the lined tunnel. The finite element analysis software is used to simulate and calculate the seepage field of the tunnel with lining, and results are compared with analytical solutions to analyze the influencing factors. The conclusions are as follows: (1)For the seepage problem of tunnels in karst areas, the seepage inflow of unsupported tunnels and supported tunnels can be obtained by complex variable function and seepage mechanics(2)Assuming that each layer of the lining pressure head is equal, the seepage force of the supported tunnel is solved by seepage mechanics. The analytical solution of the lining water pressure reduction coefficient of the tunnel in the karst area is obtained(3)The corresponding finite element analysis model is established. The relationship between and the relative permeability of the initial support to the secondary lining, the grouting circle to the secondary lining, and the surrounding rock to the secondary lining is studied from the analytical solution and the numerical solution. And the tendencies of the analytical solution and the simulation solutions are consistent(4) increases as and increase. As the permeability of the initial support and grouting circle decreases, the decrease of the analytical solution and numerical solution becomes closer. As decreases, increases gradually. increases as increases or the grouting circle and initial support become thinner or the secondary lining becomes thicker. In summary, the analytical solution of can be used to predict the seepage inflow and the seepage force of the actual engineering

Data Availability

The data used to support the findings of this study are available from the corresponding author upon request.

Conflicts of Interest

The authors declare that there are no conflicts of interest regarding the publication of this paper.

Acknowledgments

This work is supported by the National Natural Science Foundation of China (Grant Nos. 51978665 and 51678570) and Focus on research and development plan of Hunan province (No. 2015SK2053).

References

G. Fernández and T. A. Alvarez Jr., “Seepage-induced effective stresses and water pressures around pressure tunnels,” Journal of Geotechnical Engineering, vol. 120, no. 1, pp. 108–128, 1994.
View at: Publisher Site | Google Scholar
A. Bobet, “Effect of pore water pressure on tunnel support during static and seismic loading,” Tunnelling and Underground Space Technology, vol. 18, no. 4, pp. 377–393, 2003.
View at: Publisher Site | Google Scholar
T. Chisyaki, “A study on confined flow of ground water through a tunnel,” Ground Water, vol. 22, no. 2, pp. 162–167, 1984.
View at: Publisher Site | Google Scholar
A. Verruijt, “Complex variable solutions of elastic tunneling problems,” Tech. Rep., Rapport COB 96-04, 1996.
View at: Google Scholar
A. Verruijt and J. R. Booker, “Complex variable analysis of Mindlin’s tunnel problem,” in Development of Theoretical Geomechanics, pp. 3–22, Balkema, Sydney, 2000.
View at: Google Scholar
C. Butscher, “Steady-state groundwater inflow into a circular tunnel,” Tunnelling and Underground Space Technology, vol. 32, pp. 158–167, 2012.
View at: Publisher Site | Google Scholar
C. W. Du, M. S. Wang, and Z. S. Tan, “Analytic solution for seepage field of subsea tunnel and its application,” Chinese Journal of Rock Mechanics and Engineering, vol. S2, pp. 3567–3573, 2011.
View at: Google Scholar
M. El Tani, “Circular tunnel in a semi-infinite aquifer,” Tunnelling and Underground Space Technology, vol. 18, no. 1, pp. 49–55, 2003.
View at: Publisher Site | Google Scholar
H. Zhu, J. Shen, F. Zhang et al., “DEM-CFD modeling of proppant pillar deformation and stability during the fracturing fluid flowback,” Geofluids, vol. 2018, Article ID 3535817, 18 pages, 2018.
View at: Publisher Site | Google Scholar
K. H. Park, J. G. Lee, and A. Owatsiriwong, “Seepage force in a drained circular tunnel: an analytical approach,” Canadian Geotechnical Journal, vol. 45, no. 3, pp. 432–436, 2008.
View at: Publisher Site | Google Scholar
P. Li, F. Wang, Y. Long, and X. Zhao, “Investigation of steady water inflow into a subsea grouted tunnel,” Tunnelling and Underground Space Technology, vol. 80, pp. 92–102, 2018.
View at: Publisher Site | Google Scholar
H. W. Ying, C. W. Zhu, H. W. Shen, and X. N. Gong, “Semi-analytical solution for groundwater ingress into lined tunnel,” Tunnelling and Underground Space Technology, vol. 76, pp. 43–47, 2018.
View at: Publisher Site | Google Scholar
J. Wu, S. C. Li, Z. H. Xu, and J. Zhao, “Determination of required rock thickness to resist water and mud inrush from karst caves under earthquake action,” Tunnelling and Underground Space Technology, vol. 85, pp. 43–55, 2019.
View at: Publisher Site | Google Scholar
M. D. Zhang, “Study on the characteristics of seepage field and water pressure on tunnel lining in karst ground,” Tech. Rep., Beijing Jiaotong University, 2008.
View at: Google Scholar
B. Zheng, “Practical calculation of water pressure load on tunnel lining,” Tech. Rep., China Academy of Railway Sciences, 2010.
View at: Google Scholar
W. K. Kong, “Water ingress assessment for rock tunnels: a tool for risk planning,” Rock Mechanics and Rock Engineering, vol. 44, no. 6, pp. 755–765, 2011.
View at: Publisher Site | Google Scholar
Y. J. Shin, K. I. Song, I. M. Lee, and G. C. Cho, “Interaction between tunnel supports and ground convergence--consideration of seepage forces,” International Journal of Rock Mechanics & Mining Sciences, vol. 48, no. 3, pp. 394–405, 2011.
View at: Publisher Site | Google Scholar
Y. Cao, J. Jiang, K. H. Xie, and W. M. Huang, “Analytical solutions for nonlinear consolidation of soft soil around a shield tunnel with idealized sealing linings,” Computers and Geotechnics, vol. 61, pp. 144–152, 2014.
View at: Publisher Site | Google Scholar
D. M. Zhang, Z. K. Huang, Z. Y. Yin, L. Z. Ran, and H. W. Huang, “Predicting the grouting effect on leakage-induced tunnels and ground response in saturated soils,” Tunnelling and Underground Space Technology, vol. 65, pp. 76–90, 2017.
View at: Publisher Site | Google Scholar
F. M. Huang, Z. S. Tan, M. S. Wang, and X. Y. Wang, “Analytical solution for water inflow into an underwater tunnel and its application,” Engineering Sciences, vol. 11, no. 7, pp. 568–573, 2009.
View at: Google Scholar
P. Perrochet and A. Dematters, “Modeling transient discharge into a tunnel drilled in a heterogeneous formation,” Ground Water., vol. 52, no. 4, pp. 597–605, 2014.
View at: Google Scholar
E. J. Joo and J. H. Shin, “Relationship between water pressure and inflow rate in underwater tunnels and buried pipes,” Géotechnique, vol. 64, no. 3, pp. 226–231, 2014.
View at: Publisher Site | Google Scholar
P. Arjnoi, J. H. Jeong, C. Y. Kim, and K. H. Park, “Effect of drainage conditions on porewater pressure distributions and lining stresses in drained tunnels,” Tunnelling and Underground Space Technology., vol. 24, no. 4, pp. 376–389, 2009.
View at: Publisher Site | Google Scholar
B. Q. Zhang, “Analytical solution for seepage field of twin-parallel tunnel in semi-infinite plane,” Journal of the China Railway Society, vol. 39, no. 1, pp. 125–131, 2017.
View at: Google Scholar
C. Jiang, H. S. Xie, J. L. He, W. Y. Wu, and Z. C. Zhang, “Analytical solution of seepage field in karst tunnel,” Advances in Civil Engineering, vol. 2018, Article ID 9215472, 9 pages, 2018.
View at: Publisher Site | Google Scholar
H. S. Xie, C. Jiang, J. L. He, and H. X. Han, “Analytical solution for the steady-state karst water inflow into a tunnel,” Geofluids, vol. 2019, Article ID 1756856, 9 pages, 2019.
View at: Publisher Site | Google Scholar
K. H. Park, A. Owatsiriwong, and J. G. Lee, “Analytical solution for steady-state groundwater inflow into a drained circular tunnel in a semi-infinite aquifer: a revisit,” Tunnelling and Underground Space Technology, vol. 23, no. 2, pp. 206–209, 2008.
View at: Publisher Site | Google Scholar
Y. L. Zhao, C. S. Zhang, Y. X. Wang, and H. Lin, “Shear-related roughness classification and strength model of natural rock joint based on fuzzy comprehensive evaluation,” International Journal of Rock Mechanics and Mining Sciences, vol. 13, no. article 104550, 2020.
View at: Publisher Site | Google Scholar
Y. Zhao, L. Zhang, W. Wang, Q. Liu, L. Tang, and G. Cheng, “Experimental study on shear behavior and a revised shear strength model for infilled rock joints,” International Journal of Geomechanics, vol. 20, article 04020141, no. 9, 2020.
View at: Publisher Site | Google Scholar
Y. Zhao, Y. Wang, W. Wang, L. Tang, Q. Liu, and G. Cheng, “Modeling of rheological fracture behavior of rock cracks subjected to hydraulic pressure and far field stresses,” Theoretical and Applied Fracture Mechanics., vol. 101, pp. 59–66, 2019.
View at: Publisher Site | Google Scholar
Y. L. Zhao, L. Zhang, J. Liao, W. Wang, Q. Liu, and L. Tang, “Experimental study of fracture toughness and subcritical crack growth of three rocks under different environments,” International Journal of Geomechanics, vol. 20, no. 8, article 04020128, 2020.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2021 Chong Jiang et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

351

Downloads

995

Citations