Skip to content
Licensed Unlicensed Requires Authentication Published by De Gruyter December 9, 2020

Simulation of proppant transport and fracture plugging in the framework of a radial hydraulic fracturing model

  • Vasily N. Lapin EMAIL logo and Denis V. Esipov

Abstract

Hydraulic fracturing technology is widely used in the oil and gas industry. A part of the technology consists in injecting a mixture of proppant and fluid into the fracture. Proppant significantly increases the viscosity of the injected mixture and can cause plugging of the fracture. In this paper we propose a numerical model of hydraulic fracture propagation within the framework of the radial geometry taking into account the proppant transport and possible plugging. The finite difference method and the singularity subtraction technique near the fracture tip are used in the numerical model. Based on the simulation results it was found that depending on the parameters of the rock, fluid, and fluid injection rate, the plugging can be caused by two reasons. A parameter was introduced to separate these two cases. If this parameter is large enough, then the plugging occurs due to reaching the maximum possible concentration of proppant far from the fracture tip. If its value is small, then the plugging is caused by the proppant reaching a narrow part of the fracture near its tip. The numerical experiments give an estimate of the radius of the filled with proppant part of the fracture for various injection rates and leakages into the rock.

MSC 2010: 65N06

Funding statement: The work was supported by the Russian Science Foundation (project No. 17–71–20139)

References

[1] F. Boyer, E. Guazzelli, and O. Pouliquen, Unifying suspension and granular rheology. Phys. Rev. Lett. 107 (2011), No. 18, 188301-1–188301-5.10.1103/PhysRevLett.107.188301Search in Google Scholar

[2] R. D. Carter, Appendix I. Derivation of the general equation for estimating the extent of the fractured area. In: Drilling and Production Practice (Eds. G. C. Howard and C. R. Fast). Amer. Petrol. Inst., New York, 1957, pp. 261–270.Search in Google Scholar

[3] G. P. Cherepanov, Mechanics of Brittle Fracture McGraw-Hill Co., New York, 1979.Search in Google Scholar

[4] E. Detournay, Mechanics of hydraulic fractures. Annu. Rev. Fluid Mech. 48 (2016), 311–339.10.1146/annurev-fluid-010814-014736Search in Google Scholar

[5] E. V. Dontsov, An approximate solution for a penny-shaped hydraulic fracture that accounts for fracture toughness, fluid viscosity and leak-off. Royal Society Open Science 3 (2016), Art. No. 160737.10.1098/rsos.160737Search in Google Scholar

[6] E. V. Dontsov and A. P. Peirce, Slurry flow, gravitational settling and a proppant transport model for hydraulic fractures. J. Fluid Mech. 760 (2014), 567–590.10.1017/jfm.2014.606Search in Google Scholar

[7] E. V. Dontsov and A. P. Peirce, A Lagrangian approach to modelling proppant transport with tip screen-out in KGD hydraulic fractures. J. Rock Mech. & Rock. Engrg. 48 (2015), 2541–2550.10.1007/s00603-015-0835-6Search in Google Scholar

[8] E. V. Dontsov and A. P. Peirce, Proppant transport in hydraulic fracturing: Fracture tip screen-out in KGD and P3D models. Int. J. Solids Structures 63 (2015), 206–218.10.1016/j.ijsolstr.2015.02.051Search in Google Scholar

[9] D. V. Esipov, D. S. Kuranakov, V. N. Lapin, and S. G. Cherny, Mathematical models of hydraulic fracturing. Computational Technologies 19 (2014), No. 2, 33–61.Search in Google Scholar

[10] D. Garagash, E. Detournay, and J. Adachi, Multiscale tip asymptotics in hydraulic fracture with leak-off. J. Fluid Mech. 669 (2011), 260–297.10.1017/S002211201000501XSearch in Google Scholar

[11] P. S. Hammond, Settling and slumping in a Newtonian slurry, and implications for proppant placement during hydraulic fracturing of gas wells. Chemical Engrg. Sci. 50 (1995), No. 20, 3247–3260.10.1016/0009-2509(95)00152-USearch in Google Scholar

[12] G. R. Irwin, Analysis of stresses and strains near the end of a fracture traversing a plate. J. Appl. Mech. 24 (1957), 361–364.10.1115/1.4011547Search in Google Scholar

[13] P. V. Karnakov, D. S. Kuranakov, V. N. Lapin, S. G. Cherny, and D. V. Esipov, Peculiarities of the hydraulic fracture propagation caused by pumping of proppant-fluid slurry. Thermophysics and Aeromechanics 25 (2018), No. 4, 587–603.10.1134/S086986431804011XSearch in Google Scholar

[14] B. Lecampion, A. Bunger, and X. Zhang, Numerical methods for hydraulic fracture propagation: A review of recent trends. J. Nat. Gas Sci. Engrg. 49 (2018), 66–83.10.1016/j.jngse.2017.10.012Search in Google Scholar

[15] B. Lecampion and D. I. Garagash, Confined flow of suspensions modelled by a frictional rheology. J. Fluid Mech. 759 (2014), 197–235.10.1017/jfm.2014.557Search in Google Scholar

[16] L. G. Loitsianskii, Mechanics of Liquids and Gases Pergamon, 1966.Search in Google Scholar

[17] S. H. Maron and P. E. Pierce, Application of ree-eyring generalized flow theory to suspensions of spherical particles. J. Colloid Sci. 11 (1956), No. 1, 80–95.10.1016/0095-8522(56)90023-XSearch in Google Scholar

[18] A. A. Savitski and E. Detournay, Propagation of a penny-shaped fluid-driven fracture in an impermeable rock: asymptotic solutions. Int. J. Solids Structures 39 (2002), 6311–6337.10.1016/S0020-7683(02)00492-4Search in Google Scholar

[19] L. I. Sedov, Mechanics of Continuous Media, Vol. I World Scientific, 1997.10.1142/0712-vol2Search in Google Scholar

[20] D. A. Spence and P. W. Sharp, Self-similar solution for elastohydrodynamic cavity flow. Proc. R. Soc. Lond. A 400 (1985), 289–313.10.1098/rspa.1985.0081Search in Google Scholar

Received: 2020-05-05
Accepted: 2020-10-02
Published Online: 2020-12-09
Published in Print: 2020-12-16

© 2020 Walter de Gruyter GmbH, Berlin/Boston

Downloaded on 28.3.2024 from https://www.degruyter.com/document/doi/10.1515/rnam-2020-0027/html
Scroll to top button