Abstract
The aim of this study was to evaluate changes in fibre properties with high (HC)- and low consistency (LC) refining of TMP and determine how these contribute to tensile index. Two process configurations, one with only HC refining and another with HC refining followed by LC refining were evaluated in three TMP mainline processes in two mills using Norway spruce. An increase in tensile index for a given applied specific energy was similar for all LC refiners in the three lines, despite differences in the fibre property profiles of the feed pulps. Compared with only HC refined pulps at a given tensile index, HC+LC refined pulps had greater fibre wall thickness, similar fibre length, strain at break and freeness, but lower light scattering coefficient, fibre curl and external fibrillation. The degree of internal fibrillation, determined by Simons’ stain measurements, was similar for both configurations at a given tensile index. The results indicate that the increase in tensile index in LC refining is largely influenced by a decrease in fibre curl and in HC refining by peeling of the fibre walls. Compared at a given tensile index, the shive content (Somerville mass fraction) was similar for both HC+LC and HC refining.
Funding statement: The study was supported by the KK-foundation and The Swedish Energy Agency.
Acknowledgments
The KK-foundation, The Swedish Energy Agency, StoraEnso, Holmen Paper, SCA and Inovocell are gratefully acknowledged for considerable experimental help and financial support. This work was carried out within the energy efficient pulping programme (e2mp) in Sweden.
Conflict of interest: The authors declare no conflicts of interest.
References
Andersson, S. Low Consistency Refining of Mechanical pulp, process conditions and energy efficiency. Licentiate Thesis, Mid Sweden University, Sundsvall, Sweden, 2011.Search in Google Scholar
Andersson, S., Sandberg, C., Engstrand, P. (2012) Comparison of mechanical pulps from two stage HC single disc and HC double disc-LC refining. Appita J. 65(1):57–62.Search in Google Scholar
Beath, L.R., Neill, M.T., Masse, F.A. (1966) Latency in Mechanical Wood Pulps. Pulp Pap. Mag. Can. 67(10):T423–430.Search in Google Scholar
Berger, T.H. (1995) Opportunities for energy savings in TMP using low intensity low consistency post refining techniques. In: Third Int. Refining Conf. Atlanta, Vol. 1. Pira International, paper 11.Search in Google Scholar
Bonham, J.S., Flowers, A.G., Schofield, A.J. (1983) Post refining of P. radiata TMP. Appita J. 36(6):466–470.10.1093/oxfordjournals.pa.a051907Search in Google Scholar
Brecht, W., Holl, M. (1939) Schaffung eines Normalverfahrens zur Gütebewertung von Holzschliffen. Papier-fabrikant 10(24):74–86.Search in Google Scholar
Cuberos-Martinez, P., Park, S.W. (2012) Review of physical principles in low consistency refining. O PAPEL 73(8):65–72.Search in Google Scholar
Ebeling, K.I. A critical review of current theories for the refining of chemical pulps. Progress report to the Institute of Paper Chemistry, Appleton, WA, Helsinki University of Technology, Forest Products Department, Otaniemi, Finland, 1981.Search in Google Scholar
Elahimehr, A., Olson, J.A., Martinez, M. (2015) Low consistency refining of mechanical pulp: how plate pattern and refiner operating conditions change the final properties of pulp. Nord. Pulp Pap. Res. J. 30(4):609–616.10.3183/npprj-2015-30-04-p609-616Search in Google Scholar
Engstrand, P., Hammar, L.-Å., Htun, M., Pettersson, R., Svensson, B. (1990) Framställning av mekanisk och kemimekanisk massa i två steg. Swedish Patent No. SE-8801731-4 (in Swedish).Search in Google Scholar
Eriksen, O., Hammar, L.-Å. (2007) Refining mechanisms and development of TMP properties in a low-consistency refiner. In: Int. Mech. Pulping Conf. Minneapolis, USA. pp. 62–75.Search in Google Scholar
Fernando, D., Daniel, G. (2010) Characterisation of spruce thermochemical pulps at the fibre cell wall level: a method for quantitatively assessing pulp fibre development using Simons’ stain. Tappi J. 9(10):47–55.10.32964/TJ9.10.47Search in Google Scholar
Fernando, D., Daniel, G. (2011) The new microscopic method of Simons’ stain for characterizing mechanical pulps and quantitatively assessing their fibre development at the cell wall level for fundamental understanding of pulp properties. In: Int. Mech. Pulping Conf. Xi’an, China. pp. 47–53.10.32964/TJ9.10.47Search in Google Scholar
Fernando, D., Gorski, D., Sabourin, M., Daniel, G. (2013) Characterization of fiber development in high- and low-consistency refining of primary mechanical pulp. Holzforschung 67(7):735–745.10.1515/hf-2012-0135Search in Google Scholar
Fernando, D., Muhić, D., Engstrand, P., Daniel, G. (2011) Fundamental understanding of pulp property development under different thermomechanical pulp refining conditions as observed by a new Simons’ staining method and SEM observation of the ultrastructure of fibre surfaces. Holzforschung. 65:777–786.10.1515/HF.2011.076Search in Google Scholar
Ferritsius, O., Ferritsius, R., Hill, J., Karlström, A., Ferritsius, J., Eriksson, K. (2017) Process Considerations and its Demands on TMP Property Measurements – A study on tensile index. Nord. Pulp Pap. Res. J. 2(1):45–53.10.3183/npprj-2017-32-01-p045-053Search in Google Scholar
Ferritsius, O., Ferritsius, R., Reyier, S. (2009) The influence of process design on the distribution of fundamental fiber parameters. In: Proceedings, Int. Mech. Pulp. Conf., Sundsvall, Sweden. pp. 160–168.Search in Google Scholar
Ferritsius, O., Jämte, J., Ferritsius, R. (1989) SD and DD refining at Stora Kvarnsveden. In: Int. Mech. Pulping Conf. Helsinki, Finland. pp. 58–71.Search in Google Scholar
Ferritsius, R., Reyier Österling, S., Ferritsius, O. (2012) Development of TMP fibres in LC and HC-refining. Nord. Pulp Pap. Res. J. 27(5):860–870.10.3183/npprj-2012-27-05-p860-871Search in Google Scholar
Gao, J. Modelling latency removal in mechanical pulping processes. PhD thesis, Dept. Chemical and Biological Engineering, University of British Columbia, Vancouver, Canada, 2014.Search in Google Scholar
Gorski, D., Luukkonen, A., Sabourin, M., Olson, J. (2012a) Two stage Low consistency refining of mechanical pulp. Appita J. 65(3):244–249.Search in Google Scholar
Gorski, D., Mörseburg, K., Olson, J., Luukkonen, A. (2012b) Fibre and fines quality development in pilot scale high and low consistency refining of ATMP. Nord. Pulp Pap. Res. J. 27(5):872–881.10.3183/npprj-2012-27-05-p872-881Search in Google Scholar
Hammar, L.-Å., Htun, M., Svensson, B. (1997) A Two Stage Refining Process to Save Energy for Mechanical Pulps. In: Proc. Int. Mech. Pulping Conf. Stockholm, Sweden. pp. 257–262.Search in Google Scholar
Hammar, L.-Å., Salmen, L., Sandberg, C., Sundström, L. (2010) The effect of process conditions on pulp quality development in low consistency refining of mechanical pulp – TMP. Appita J. 63(5):257–262.Search in Google Scholar
Höglund, H., Fredriksson, B., Eriksson, I. (1977) In: Int. Mech. Pulp. Conf. Helsinki, Finland, vol. 17B:1. pp. 53–66.Search in Google Scholar
Imppola, A., Mörseburg, K., Johansson, L., Ertsås, P.A. (2013) Effects of inlet pulp quality and specific energy consumption in mill scale low-consistency refining of mechanical pulp. In: 8th International Fundamental Mechanical Pulp Research Seminar, 29-31 January 2013, Åre, Sweden.Search in Google Scholar
Johansson, O., Fernando, D., Ferritsius, R., Daniel, G., Ferritsius, O. (2016) Advancements in optical analysis yields new insight to mechanical pulping processes in an efficient and inexpensive way. In: Int. Mech. Pulping Conf. Jacksonville, Florida. pp. 99–108.Search in Google Scholar
Jones, H.W.H. (1966) Occurrence and removal of kink and curl from mechanical pulp fibres as related to paper properties. Pulp Pap. Mag. Can. 67(1):T283–291.Search in Google Scholar
Karnis, A. (1994) The mechanism of fibre development in mechanical pulping. J. Pulp Pap. Sci. 20(10):J280–288.Search in Google Scholar
Kerekes, R., Meltzer, F. (2018) The influence of bar width on bar forces and fibre shortening in low consistency pulp refining. Nord. Pulp Pap. Res. J. 33(2):220–225.10.1515/npprj-2018-3028Search in Google Scholar
Kure, K.-A., Sabourin, M.J., Dahlqvist, G., Helle, T. (2000) Adjusting refining intensity by changing refiner plate design and rotational speed – Effects on structural fibre properties. J. Pulp Pap. Sci. 26(10):346–352.Search in Google Scholar
Lindholm, C.A. (1980) Comparison of some papermaking properties of groundwood and thermomechanical pulp by means of artificial blends of pulp fractions. Pap. Puu 62(10):593–606.Search in Google Scholar
Luukkonen, A., Olson, J.A., Martinez, D.M. (2010) Low consistency of mechanical pulp: A methodology to relate operating conditions to paper properties. J. Pulp Pap. Sci. 36(3–4):107–111.Search in Google Scholar
Mohlin, U.-B. (1980a) Latency in thermomechanical pulps: Contribution of the various pulp fractions. Tappi J. 63(3):83–86.Search in Google Scholar
Mohlin, U.-B. (1980b) Properties of TMP fractions and their importance for the quality of printing papers – Part 2. Sven. Papp.tidn. 83(18):513–519.Search in Google Scholar
Mohlin, U.-B. (1995) Fibre development during mechanical pulp refining. In: Int. Mech. Pulping Conf. Ottawa, USA. pp. 71–77.Search in Google Scholar
Page, D.H. (1989) The Beating of Chemical Pulps – The Actions and the Effects. In: Papermaking Raw Materials: Transactions of the Ninth Fundamental Research Symposium. Eds. Baker, C.F., Punton, V.W. Mechanical Engineering Publications Ltd., London, U.K. pp. 1–37.Search in Google Scholar
Page, D.H., Seth, R.S., Jordan, B.D., Barbe, M.C. (1985) and references therein. Curls, crimps, kinks and microcompressions in pulp fibres – their origin, measurement and significance. In: Papermaking Raw Materials, Trans. VIIIth Fund. Res. Symp. Oxford. Ed. Punton, V. FRC, Manchester, 2003. pp. 183–227. ISBN: 0 9541126 8 7.Search in Google Scholar
Reme, P.A., Johnsen, P.O., Helle, T. (2002) Assessment of fibre transverse dimensions using SEM and image analysis. J. Pulp Pap. Sci. 28(4):122–127.10.1007/s00107-002-0310-4Search in Google Scholar
Reme, P.A., Kure, K.-A., Gregersen, O.W., Helle, T. (1999) Optimal mechanical pulp fibres for improved publication paper: targets and treatments. In: Int. Mech. Pulp. Conf., Houston, USA. pp. 171–182.Search in Google Scholar
Reyier, S. Bonding ability distribution of fibers in mechanical pulp furnishes. Licentiate Thesis, Mid Sweden University, Sundsvall, Sweden, 2008.Search in Google Scholar
Reyier, S., Ferritsius, O., Ferritsius, R. (2012) The influence of fiber dimensions on mechanical pulp long fiber tensile index and density. Nord. Pulp Pap. Res. J. 27(5):844–859.10.3183/npprj-2012-27-05-p844-859Search in Google Scholar
Rundlöf, M. (2002) Interaction of dissolved and colloidal substances with fines of mechanical pulp. PhD thesis, Royal Institute of Technology, Stockholm, Sweden. ISSN 1104-7003, fig. 2.6, p. 15.Search in Google Scholar
Sandberg, C., Berg, J.-E., Engstrand, P. (2017) Low consistency refining of mechanical pulp – system design. Tappi J. 16(7):419–429.10.32964/TJ16.7.419Search in Google Scholar
Seth, R.S. (2006) The importance of fibre straightness for pulp strength. Pulp Pap. Can. 107(1):T1–T8.Search in Google Scholar
Welch, L.V.S. (1999) Low consistency refining of mechanical pulps. PhD thesis, University of British Columbia, Vancouver, Canada.Search in Google Scholar
Yu, X., Minor, J.L., Atalla, R.H. (1995) Mechanism of action of Simons’ stain. Tappi J. 78(6):175–180.Search in Google Scholar
© 2020 Walter de Gruyter GmbH, Berlin/Boston
