The method of singular integral equations is used to obtain the solution of the antiplane problem of fracture mechanics for an orthotropic plane with two-section kinked crack with regard for the specific features of stresses at the tips of angular cracks. For this purpose, we apply the unified approach developed earlier to the solution of the problems of stress concentration in isotropic bodies with pointed and rounded notches.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
M. P. Savruk and A. Kazberuk, Stress Concentration in Solids with Notches, Vol. 14 in: V. V. Panasyuk (editor), Fracture Mechanics and Strength of Materials: A Handbook [in Ukrainian], Spolom, Lviv (2012).
M. P. Savruk and A. Kazberuk, Stress Concentration at Notches, Springer, Cham (Switzerland) (2017).
M. P. Savruk, A. Kazberuk, and G. Tarasiuk, “Distribution of stresses over the contour of a rounded V-shaped notch under antiplane deformation,” Fiz.-Khim. Mekh. Mater., 47, No. 6, 7–14 (2011); English translation: Mater. Sci., 47, No. 6, 7–14 (2012).
A. Kazberuk and M. P. Savruk, “Distribution of stresses near V-notches in an orthotropic plane under symmetric loads,” Fiz.-Khim. Mekh. Mater., 52, No. 1, 61–68 (2016); English translation: Mater. Sci., 52, No. 1, 62–71 (2016).
S. G. Lekhnitskii, Theory of Elasticity of Anisotropic Bodies [in Russian], Nauka, Moscow (1977).
T. C. T. Ting, Anisotropic Elasticity. Theory and Applications, Oxford Univ. Press, Oxford (1996).
M. P. Savruk, A. Kazberuk, and L. I. Onyshko, “Influence of the anisotropy of materials on the distribution of stresses near parabolic notches,” Fiz.-Khim. Mekh. Mater., 51, No. 6. 24–33 (2015); English translation: Mater. Sci., 51, No. 6, 773–784 (2016).
M. P. Savruk, Two-Dimensional Problems of Elasticity for Bodies with Cracks [in Russian], Naukova Dumka, Kiev (1981).
M. P. Savruk, L. Y. Onyshko, and O. I. Kvasnyuk, “Distribution of stresses near angular notches on an orthotropic elastic plane under conditions of antiplane deformation,” Fiz.-Khim. Mekh. Mater., 55, No. 3, 7–16 (2019); English translation: Mater. Sci., 55, No. 3, 299–310 (2019).
A. Kazberuk, M. P. Savruk, and A. Seweryn, “Stress intensity factors at corner points of chevron crack in orthotropic plate,” in: Proc. of the Eighth Internat. Symp. on Mech. Mater. Struct., Bialystok (2015), p. 84.
S. V. Serensen and G. P. Zaitsev, Load-Bearing Ability of Thin-Walled Structures Made of Reinforced Plastics with Defects [in Russian], Naukova Dumka, Kiev (1982).
M. P. Savruk, Stress Intensity Factors in Bodies with Cracks, in: V. V. Panasyuk (editor), Fracture Mechanics and Strength of Materials: A Handbook [in Russian], Naukova Dumka, Kiev (1988).
E. Smith, “Crack bifurcation in brittle solids,” J. Mech. Phys. Solids, 16, No. 5, 329–336 (1968).
E. Smith, “The extension of two parallel non-coplanar cracks by an applied stress,” Int. J. Eng. Sci., 9, No. 7, 631–638 (1971).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Fizyko-Khimichna Mekhanika Materialiv, Vol. 56, No. 2, pp. 7–13, March–April, 2020.
Rights and permissions
About this article
Cite this article
Savruk, M.P., Onyshko, L.I., Kvasnyuk, O.I. et al. Stressed State of an Orthotropic Plane with Two-Section Kinked Crack Under Antiplane Deformation. Mater Sci 56, 143–151 (2020). https://doi.org/10.1007/s11003-020-00408-y
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11003-020-00408-y