We present the results of experimental investigations of the distribution of deformation indicators and rolling forces along the length of brass (L63) strips in a 150 × 235 two-roll mill equipped with a microcontroller system for high-precision measurements of loads acting upon the rolls. The results of the quantitative analyses of changes in the sizes of strips and rolling forces on stationary and nonstationary sections along the strip length are presented. A significant effect of the outer parts of the strip on the rolling force and the pressure of the metal upon the rolls is established. On the basis of the experimental results, we propose an equation for the evaluation of the influence of the outer parts of the strip on the rolling force and pressure. The equation for the mean pressure of the metal upon the rolls is improved with regard for the influence of the outer parts and the stiffness of the strip on the site of deformation in the process of thin-sheet rolling. It is shown that the proposed equations make it possible to increase the accuracy of evaluation of pressure and determination of rolling forces along the length of thin strips.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
M. Ya. Brovman and A. F. Pimenov, “Development of the rolling production for 500 years,” Vestn. Mashinostr., No. 11, 74–82 (2004)
M. Ya. Brovman, Combined Processes of Continuous Casting and Rolling [in Russian], LAMBERT, Saarbrücken (2014).
R. L. Shatalov, “Improvement of the quality of strips made of nonferrous metals and alloys,” Tsvet. Met., No. 5, 65–70 (2001).
A. V. Zinov’ev, A. I. Kolpashnikov, P. I. Polukhin, Yu. P. Glebov, D. I. Piryazev, V. S. Gorokhov, and A. M. Galkin, Technology of Pressure Treatment of Nonferrous Metals and Alloys [in Russian], Metallurgiya, Moscow (1992).
M. Ya. Brovman, Power and Force Parameters and the Improvement of the Technology of Rolling [in Russian], Metallurgiya, Moscow (1995).
I. M. Pavlov, “On the role of outer parts of a strip in various cases of the rolling,” Izv. Akad. Nauk SSSR. Metal., No. 6, 101–106 (1969).
A. I. Tselikov, Foundations of the Theory of Rolling [in Russian], Metallurgiya, Moscow (1965).
A. I. Tselikov, G. S. Nikitin, and S. E. Rokotyan, Theory of Lengthwise Rolling [in Russian], Metallurgiya, Moscow (1980).
M. A. Zaikov, V. P. Polukhin, A. M. Zaikov, and L. N. Smirnov, Process of Rolling [in Russian], MISiS, Moscow (2004).
N. D. Lukashkin, L. S. Kokhan, and N. N. Lebedev, Stresses and Strains in the Processes of Pressure Treatment of Metals [in Russian], Akademkniga, Moscow (2004).
S. M. Gorbatyuk, V. A. Osadchii, and E. Z. Tuktarov, “Calculation of the geometric parameters of rotary rolling by using the automated design system Autodesk Inventor,” Metallurgist, 55, Nos. 7–8, 543–546 (2011); DOI: https://doi.org/10.1007/s11015-011-9465-8.
S. M. Gorbatyuk, V. M. Pavlov, A. N. Shapoval, and M. S. Gorbatyuk, “Experimental use of rotary rolling mills to deform compacts of refractory metals,” Metallurgist, 42, Nos. 5-6, 178–183 (1998); DOI: https://doi.org/10.1007/BF02766359.
V. A. Osadchii, S. M. Gorbatyuk, D. I. Filippov, and N. S. Kuprienko, “Development of a method for the visualization of the process of forming of curved profiles in the software used for the numerical analyses of the roll passes,” Metallurgist, 63, Nos. 5-6, 658–664 (2019); DOI: https://doi.org/10.1007/s11015-019-00872-1.
S. M. Gorbatyuk, S. R. Romanov, and I. G. Morozova, “Computer simulation of the cooling system for rollers of the finishing stand of a wide-strip hot-rolling mill and the development of a new scheme of cooling,” Metallurgist, 63, Nos. 7-8, 836–840 (2019); DOI: https://doi.org/10.1007/s11015-019-00897-6.
M. M. Skripalenko, V. A. Romantsev, L. M. Kaputkina, S. P. Galkin, M. N. Skripalenko, and V. V. Cheverikin, “Investigations of the stationary and nonstationary stages in the course of two-roll and three-roll screw rolling of billets made of 12Kh18N10T steel,” Metallurg, No. 4, 49–57 (2019).
L. S. Kokhan, A. V. Aldunin, and Yu. B. Slavgorodskaya, “Lowering of pressure in the course of hot rolling of strips with the use of variable back tension,” Tekhnol. Metal., No. 6, 22–27 (2019).
R. L. Shatalov, M. A. Kulikov, and G. A. Shcherban’, “Distributions of the thickness, width, and rolling force along the length of sheets in a rolling mill,” in: Proc. of the XII Congr. of Rollers [in Russian], Vol. 1, Grin Print, Moscow (2019), pp. 59–64.
B. V. Kucheryaev, A. V. Zinov’ev, and V. B. Krakht, “Experimental verification of a formula for the evaluation of the energy and force parameters of sheet rolling,” Proizvod. Prokat., No. 4, 2–7 (2002).
R. L. Shatalov, A. S. Lukash, and Yu. F. Timin, “Development and study of a microprocessor system of monitoring of the rolling forces in a two-roll sheet mill,” Metallurg, No. 10, 70–73 (2015).
R. L. Shatalov, Design of Parameters of the Processes of Sheet Rolling. A Textbook [in Russian], Moskovskii Politekh, Moscow (2018).
G. S. Nikitin, Theory of Continuous Lengthwise Rolling [in Russian], Bauman Moscow State Technical University, Moscow (2009).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Metallurg, Vol. 64, No. 7, pp. 77–84, July, 2020.
Rights and permissions
About this article
Cite this article
Shatalov, R.L., Kulikov, M.A. Influence of Outer Parts of a Strip on the Deformation and Force Parameters of Thin-Sheet Rolling. Metallurgist 64, 687–698 (2020). https://doi.org/10.1007/s11015-020-01045-1
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11015-020-01045-1