Thermophilic Solid-State Anaerobic Digestion of Corn Straw, Cattle Manure, and Vegetable Waste: Effect of Temperature, Total Solid Content, and C/N Ratio

Su, Lianghu; Sun, Xu; Liu, Chenwei; Ji, Rongting; Zhen, Guangyin; Chen, Mei; Zhang, Longjiang

doi:https://doi.org/10.1155/2020/8841490

Archaea

On this page

Abstract Introduction Materials and Methods Results and Discussion Conclusion Data Availability Disclosure Conflicts of Interest Acknowledgments Supplementary Materials References Copyright Related Articles

Special Issue

Biological Processes for Pollution Control: Current Research and Emerging Technologies 2020

View this Special Issue

Research Article | Open Access

Volume 2020 | Article ID 8841490 | https://doi.org/10.1155/2020/8841490

Thermophilic Solid-State Anaerobic Digestion of Corn Straw, Cattle Manure, and Vegetable Waste: Effect of Temperature, Total Solid Content, and C/N Ratio

Lianghu Su,¹Xu Sun,^1,2Chenwei Liu,¹Rongting Ji,¹Guangyin Zhen,³Mei Chen,¹and Longjiang Zhang¹

Academic Editor: Rong Chen

Received19 May 2020

Revised05 Oct 2020

Accepted26 Oct 2020

Published11 Nov 2020

Abstract

Thermophilic solid-state anaerobic digestion (SS-AD) of agricultural wastes, i.e., corn straw, cattle manure, and vegetable waste, was carried out in this study. The effects of temperature (40-60°C), initial solid content (ISC, 17.5-32.5%), and C/N ratio (15-32 : 1) on biogas production were evaluated using a Box-Behnken experimental design (BBD) combined with response surface methodology (RSM). The results showed that optimization of process parameters is important to promote the SS-AD performance. All the factors, including interactive terms (except the ISC), were significant in the quadratic model for biogas production with SS-AD. Among the three operation parameters, the C/N ratio had the largest effect on biogas production, followed by temperature, and a maximum biogas yield of 241.4 mL gVS^-1 could be achieved at 47.3°C, , and . After 20 d of SS-AD, the microbial community structure under different conditions was characterized by high-throughput sequencing, showing that Firmicutes, Bacteroidetes, Chloroflexi, Synergistetes, and Proteobacteria dominated the bacterial community, and that Firmicutes had a competitive advantage over Bacteroidetes at elevated temperatures. The biogas production values and relative abundance of OPB54 and Bacteroidia after 20 d of SS-AD can be fitted well using a quadratic model, implying that OPB54 and Bacteroidia play important roles in the methanogenic metabolism for agricultural waste thermophilic SS-AD.

1. Introduction

China is facing tremendous challenges in managing its massive amount of agricultural waste in rural areas. In 2016, China produced 897 Mt of crop residues, and almost one-quarter of these crop residues were burned in the field after harvest, aggravating the air pollution [1, 2]. With the constant growth of livestock husbandry, the amount of livestock excrement in China increased by 12.8% from 367 to 414 Mt (dry) in 2007-2015, causing grave concerns about the water pollution [3].

Anaerobic digestion is a multistage biological process that, in addition to the treatment and stabilization of waste, allows the production of biogas as a versatile, renewable energy source and the recovery of residual solid (or liquid) as green fertilizers [4, 5]. Unlike other biomass resources, agricultural wastes are preferred for biogas production due to their large-scale availability and low cost, and they do not directly compete with food or feed production [6]. When compared to those of other treatments, these advantages, together with environmental impacts, make the synergistic utilization of the agricultural organic waste by anaerobic codigestion a promising technology [4].

Compared to liquid anaerobic digestion (L-AD), solid-state anaerobic digestion (SS-AD) operated at a total solid (TS) content above 15% has much higher volumetric methane productivity, requires less energy for heating and stirring, and generates less wastewater [7, 8]. The resulting residue (called digestate) of SS-AD with a lower moisture content would be favourable for transportation and can be valorized as a fertilizer for land applications [9]. Although there are many obstacles, such as difficulties in feeding and discharging, uneven mass transfer, and acid inhibition [10, 11], SS-AD has still been adopted for lignocellulosic biomass, especially in rural areas of China. In China, L-AD is facing a severe problem in treating anaerobic digester effluent, which has a high concentration of nutrients and low oxygen availability. Direct discharge of effluent to natural waters will deteriorate the water quality, affect aquatic organisms, and lead to biodiversity degradation [12]. The application of effluent to land is difficult due to insufficient storage and transportation facilities and limited land carrying capacity [13]. Further treatment to meet the threshold set by the Chinese standard for irrigation water quality (GB5084-2005) [14], such as mg L^-1, would be economically unfeasible.

SS-AD digesters are usually operated based on empirical knowledge rather than performance optimization [8]. The key parameters (such as moisture content, C/N ratio, and temperature) can be further optimized to achieve a better SS-AD performance. Le Hyaric et al. [15] reported that the initial substrate concentration (ISC) affects all steps of anaerobic digestion. Abbassi-Guendouz et al. [16] showed that an elevated ISC leads to lower methane production and substrate conversion. Fernandez et al. [17] observed that methane production decreased by 17% when the ISC increased from 20% to 30% in a dry mesophilic digester. Improper C/N ratios can result in high total ammonia nitrogen (TAN) release in the digester [18]. Temperature is also an extremely important factor for SS-AD; changes in temperature can alter the activity of enzymes in the microbiome and affect substrate degradation and methanogenesis [11]. It has been reported that for lignocellulosic biomass, thermophilic SS-AD led to a greater reduction in the amount of cellulose and hemicelluloses than mesophilic SS-AD [19]. However, instability is a crucial concern for applying SS-AD under thermophilic conditions [20]. Accumulation of VFAs and decreasing pH values during the start-up phase of thermophilic SS-AD digester failure have been also observed [7, 21].

To the best of our knowledge, the effects of the temperature, total solid content, and C/N ratio involved in the mesophilic SS-AD process of agricultural waste materials have been reported, but the effects of these factors on thermophilic SS-AD are poorly understood. In this study, SS-AD of corn straw, cattle manure, and vegetable waste was investigated under thermophilic conditions (40-60°C). The biogas yield, pH, and TAN concentration were characterized after 20 d of SS-AD. The effects of the temperature, ISC, and C/N ratio on biogas production were evaluated using the Box-Behnken experimental design (BBD) combined with response surface methodology (RSM). Microbial community structures were further characterized after 20 d of SS-AD using high-throughput sequencing.

2. Materials and Methods

2.1. Substrates and Inoculum

Before use, corn straw was chopped into small pieces (~1-2 cm) using a shredding machine. The cellulose, hemicellulose, and lignin contents of corn straw were 45.79%, 21.90%, and 8.01%, respectively. Cattle manure with a moisture content of 16.72% and a C/N ratio of 14.67 was obtained from a dairy farm near the city of Nanjing (Jiangsu Province, China). Vegetable waste, mainly Chinese cabbage (Brassica rapa L. ssp. pekinensis), was obtained from a local vegetable market in Nanjing. Inoculated sludge with a total solid (TS) content of 8.31% and VS content of 82.53% was collected from a methanogenic reactor that treats starch wastewater from a wastewater treatment plant (WWTP) in Shanghai, China. To reduce the endogenous gas production, the inoculated sludge was preincubated anaerobically for 7 days. Sixteen bacterial phyla were represented for inoculated sludge, with Chloroflexi, Bacteroidetes, Proteobacteria, and Firmicutes being the most abundant phyla, accounting for 33.2%, 14.7%, 11.6%, and 12.1% of the total bacterial sequences, respectively. The fundamental characteristics of corn straw, cattle manure, and vegetable waste are shown in Table 1.

2.2. Experimental Procedure

A three-level-three-factor Box-Behnken design (BBD) was chosen to evaluate the effects and interactive effects of the three independent variables, i.e., temperature (40°C, 50°C, and 60°C), ISC (17.5%, 25.0%, and 32.5%), and C/N ratio (15 : 1, 23.5 : 1 and 32 : 1), as , , and , respectively, on the response variable biogas production (mL gVS^-1) during SS-AD. The experiments were designed by Design Expert (Version 8.0.6, Statease, Minneapolis, USA), and the real values of the operating variables are summarized in Table 2. For SS-AD, corn straw, cattle manure, and vegetable waste were rigorously mixed in a mass ratio of 40 : 10 : 0.5 (dry wt.) in the laboratory. A 100 g mixed sample with a moisture content of 67.5% (adjusted by distilled water) was used as a mixed substrate. Different doses of distilled water and urea were further added to the mixed substrate to adjust the ISC and C/N ratio. Activated sludge was introduced as inoculum, with a feedstock-to-inoculum ratio (F/I, based on VS) of 3. SS-AD was carried out in 500 mL borosilicate bottles (Wente Experimental Ware, China) with a stainless steel vent pipe (Figure S1) and lasted for 20 d. Bottles were flushed with high-purity N₂ to exclude oxygen and were sealed with a silicone gasket and stopper. The temperature during SS-AD was maintained by a thermostatic water bath (DK-98, Taisite Instrument Co. Ltd., China). An aluminium foil bag (E-switch, Shenyuan Scientific Equipment Co., China) was connected to the gas outlet by a three-way valve (Discofix, B. Braun, Germany) to collect biogas from each bottle. Different parameters, such as pH, TAN, and microbial community, were analyzed after 20 d of SS-AD. One-way ANOVA was employed to study the primary effects and interactions on biogas production between the parameters selected.

2.3. Analytical Methods

The pH of the digestate was measured by a digital pH meter (Sartorius, Model PB-10, Germany) after shaking for 20 min at 25°C with a liquid-solid ratio of 10 : 1. The TAN concentration of digestate extracted by ultrapure water was determined by a continuous flow analyser (Skalar San++, Netherlands). To analyze the structure of the microbial communities after 20 d of SS-AD under different operating conditions, 0.5 g of the sample was used for DNA extraction. Total DNA was extracted by a Fast DNA SPIN Kit (BIO 101, Carlsbad, CA, USA) according to the manufacturer’s protocol. The V3-V4 region of the 16S rRNA gene was amplified using universal primers 338F (5-ACT CCT ACG GGA GGC AGC AG-3) and 806R (5-GGACTA CHV GGG TWT CTA AT-3). The amplicons from each sample were sequenced with the Illumina MiSeq platform (Illumina Company, San Diego, CA, USA). Diversity statistics and operational taxonomic unit (OTU) estimators were calculated using mothur software [22]. The coverage of the clone library was calculated based on the formula , where 1 is the number of unique OTUs, and N is the total number of clones in a library.

3. Results and Discussion

3.1. SS-AD Performance

The cumulative biogas volumes with different parameters (ISC, T, and C/N ratio) after 20 d of SS-AD are shown in Table 3. The maximum biogas production of 236 mL gVS^-1 was obtained at 50°C, , and . It is noted that the operating parameters at 40°C, , and cause digester failure, generating little biogas (2.80 mL gVS^-1) during the entire digestion process. According to the three-level-three-factor BBD, the average biogas volume yield was 110.9 mL gVS^-1 with 12 different operating parameter settings (excluding failed digester). The results showed that optimizing the process parameters is important to promote the SS-AD performance.

3.2. pH and TAN Concentrations

After 20 d of anaerobic digestion, the NH₄⁺-N concentration of each run was determined. In this study, NH₄⁺-N was derived from cattle manure (N-rich substrates), degradation of nitrogenous organic matter (e.g., proteins and amino acids), and/or conversion of urea by deamination. TAN is a key macronutrient for microbial growth and a buffer to stabilize the pH, while high concentrations of TAN would decrease the methanogen activity and cause anaerobic digestion failure due to ammonia inhibition [23]. Production of excessive ammonia nitrogen is more likely to happen in SS-AD than L-AD due to the higher organic loading and lower water content of the former [24]. As shown in Table 3, the concentration of TAN ranged from 1641-3613 mg kg^-1 for all samples after 20 d of anaerobic digestion. It can also be seen that a high TAN concentration was caused by a combination of elevated temperature, high ISC, and low C/N ratio. It is reported that in the L-AD system, the TAN concentration should not reach the range of 1500-3000 mg L^-1 to avoid the toxicity of ammonia [25]. Wang et al. [24] showed that a TAN level of 4.3 g kg^-1 caused a reduction in the reaction rates and microbial activities for hydrolysis of cellulose and methanogenesis from acetate, and a TAN level of 2.5 g kg^-1 decreased the methane yield during SS-AD of corn stover. Therefore, it is believed that the biogas yield from runs 4, 6, and 10 was inhibited due to the excessive TAN levels (greater than 3.0 g kg^-1). It seems that the SS-AD failure of run 7 was not caused by the accumulation of VFA (decreasing pH value) or excessive TAN level. The cause for the SS-AD failure of run7 is still unclear. TAN includes both NH₄⁺ and free ammonia (FAN, NH₃). FAN is the main cause of ammonia inhibition because it is membrane permeable [26, 27]. So far, a FAN calculation method has rarely been applied in SS-AD, the digestate of which generally has a higher ionic strength than that in L-AD [23]. FAN inhibition is related to the characteristics of the substrate, pH, process temperature, concentrations of ammonium and ammonia, etc. [28]. Capson-Tojo et al. [4] demonstrated that pH and temperature, rather than the TAN content itself, are the main factors affecting FAN inhibition. Among the high-TAN samples, the biogas yield of run 10, with a higher pH value, was much greater than that of run 4 and run 6. This phenomenon might be related to the higher FAN concentrations at increasing temperatures [23].

3.3. Modeling of SS-AD for Biogas Production

The results in Table 3 were used for multiple regression analysis using the polynomial model equation. This approach enabled the prediction of the optimum degree of biogas production and its corresponding optimum variables. One-way analysis of variance (ANOVA) was employed to test and analyze different models. In this study, the best-fit model found for the biogas production was a quadratic model. The value of the model was 8.45, with a low value of 0.0051. However, the value (0.95) and value (0.0256) of the lack of fit implied that the prediction for the fit of the model was not good. Further, studentized residual analysis showed that run 2 was an outlier due to its externally studentized residuals being larger than 5. Therefore, the data of run 2 were not included in the following modeling analysis.

The following polynomial quadratic model for biogas production was then adjusted to a better prediction by applying response surface regression (RSREG), as shown in Eq. (1), where is the temperature, is the ISC, and is the C/N ratio.

ANOVA was conducted for the response variable, as presented in Table 4. The model value of 56.10 indicated that the quadratic model was statistically significant for biogas production. The high coefficient of 0.9883 ensured a satisfactory adjustment of the quadratic model to the experimental data, implying that only 1.17% of biogas production variability could not be explained by the proposed model. The adjusted -square () and Adeq-Precision of 18.17 were also high, supporting the high significance of the model. The lack-of-fit value of 0.33 revealed that the lack of fit was insignificant. Therefore, it is reasonable to believe that the proposed model is reliable for predicting the biogas production of SS-AD.

The significance test for the regression coefficients determined by values was carried out. The larger the value of the regression parameter was, the smaller the values were, indicating that this parameter has a greater impact on biogas production. The corresponding values showed that all the factors, including interactive terms, were significant model terms, except the ISC (, ). Among the three operating parameters, the C/N ratio (, ) had the largest effect on biogas production, followed by temperature (, ).

It is important to check the model adequacy of biogas production for response surface optimization, as the model would give poor or misleading results if not well fit. The normal probability plot indicates whether the residuals follow a normal distribution, in which case the points will follow a straight line [29]. The normality assumption was examined by constructing a plot of standardized residuals vs. the normal % probability. As shown in Figure 1(a), the normal probability plot was approximated well by a straight line, indicating that the response variables did not require transformation, and that there were no apparent abnormality issues [29]. Figure 1(b) shows that the predicted values of the responses from the biogas production model accorded well with the actual values. The distribution of data plots is relatively close to a straight line, indicating reasonably adequate agreement between the actual and predicted values and confirming that the model could be further used to navigate the space defined by BBD.

(a)

(b)

3.4. Optimization of Biogas Production Operating Parameters

The experimental results were visualized in three-dimensional response surface plots and the corresponding contour plot, which show the simultaneous effect of two independent factors on biogas production, with one variable maintained at its central level. Figure 2(a) illustrates the effects of ISC and T on biogas production at a C/N ratio of 23.5. Noticeable changes in the biogas production by changing each parameter were recorded, and the results showed that both parameters and their interaction are effective [8]. According to Figure 2(a), biogas production showed a significant increasing trend as the ISC increased from 17.5 to 25% and temperature increased from 40 to 50°C; the biogas production then decreased when the ISC and temperature increased beyond those values.

(a)

(b)

(c)

The TS content is responsible for the mass transfer in SS-AD [30]. It is believed that a decreasing TS content might facilitate substrate conversion in SS-AD because metabolism by microorganisms (including hydrolytic bacteria, acidogenic bacteria, acetogenic bacteria, and methanogenic archaea) occurs in the water-soluble phase [31–33]. However, the maximum value of biogas production was not achieved at the lowest ISC (17.5%) in this study. It appears that in this study, the increase in the feed TS content up to 25% has a positive effect on biogas production. Yi et al. [34] showed that biogas production increased as the TS content increased from 5%-20%, and Paritosh et al. [35] reported that increasing the TS content beyond 25% did not result in a significant increase in the methane yield, consistent with our results. Yan et al. [8] reported that biogas production decreased drastically when increasing the ISC from 20 to 35%. This phenomenon suggested that the effect of the TS content on biogas production is related to the specific characteristics of the substrates, the type of inoculum, and the interaction of other operating parameters (such as process temperature) [30]. The operating temperature determines the fate of the microbes, which may disturb the overall reaction process. In this study, further increasing the temperature above 50°C exhibited a negative effect on biogas production. It has been reported that thermophilic conditions in SS-AD enhance the hydrolysis of the substrate by stimulating hydrolytic microorganisms, and an excessive process temperature may hamper or inhibit the methanogenesis process due to VFA accumulation [30, 36]. The results from previous studies were consistent with our results.

Figures 2(b) and 2(c) illustrate the effects of the ISC and C/N ratio on biogas production at 50°C and the effects of the T and C/N ratio on biogas production at an ISC of 25%, respectively. It is found that the enhancement of biogas production can be achieved when the ISC increased from 17.5 to 25% at the temperature of 50°C and then decreased gradually after that (Figure 2(b)), showing no difference from the results shown in Figure 2(a). It is also observed that the biogas production decreased when the C/N ratio increased from 15 to 32 at the temperature of 50°C, confirming that a high C/N ratio results in the rapid consumption of nitrogen by methanogens and further results in a lower biogas yield [37]. These results also suggested that the microbial activities for hydrolysis and methanogenesis at 50°C could withstand the inhibition caused by excessive free ammonia production.

3.5. Optimization of SS-AD

The SS-AD parameters were optimized based on the quadratic model using the optimization module of the Design Expert software. The results showed that a maximum biogas production capacity of 265 mL gVS^-1 would be achieved with an ISC of 23.4%, T of 47.7°C, and C/N ratio of 17.2, without considering other factors. It is noteworthy that the optimized C/N ratio is relatively low, indicating that considerable extra urea or other nitrogen sources should be added during the SS-AD process, which would increase the operating cost. Moreover, a low C/N ratio might hinder the composting of the digestate of SS-AD [38]. Torres-Climent et al. reported that a C/N ratio of 28-31 showed the most rapid temperature increase during composting of the solid phase of digestate [39]. Additionally, a relatively lower temperature would be desired for SS-AD because of the stability and lower heating energy costs. Therefore, a goal was set to maximize biogas production and the C/N ratio while minimizing the process temperature. Concretely, for optimization, the importance of temperature and the C/N ratio were considered important (+), and biogas production was considered the most important (+++++). The results indicated that a biogas productivity of 241.4 mL gVS^-1 would be achieved at 47.3°C, , and . As the optimized parameters, i.e., ISC, C/N ratio, and T, are close to the parameters designed in this study, a verification experiment of SS-AD was not further carried out.

3.6. Comparison of the Community Diversity of Bacteria

After 20 d, the bacterial communities in SS-AD samples from run 1 to run 14 were further characterized by amplicon sequencing of 16S rRNA genes. As shown in Table 5, different high-quality sequences ranging from 16,877 to 33,006 per sample were obtained. All of the sequences were aligned and clustered to calculate the operational taxonomic units (OTUs) based on 97% sequence identity, resulting in 1105 OTUs at a sequencing depth of 16000 reads per sample and coverage of 99.0-99.4%. These results showed that the Chao 1 estimator of richness and Shannon diversity index of the microbial community at 60°C (except S6) were lower than those at 50°C, indicating that the microbial communities at 50°C were generally more complex than those at 60°C. The differences in microbial communities among SS-AD samples were also described by principal coordinate analysis (PCoA), as shown in Figure 3. The first two axes of the PCoA explained 42.19% and 22.09% of the variance, respectively, or collectively 64.28% of the variance. This analysis also showed a distinct community structure among SS-AD samples that can be separated into three groups based on incubation temperatures (i.e., 40, 50, and 60°C), except S11, which had excessive acidification (Figure 4).

(a)

(b)

(c)

Ten major phyla, represented by more than 1% of the total bacterial sequence of each phylum, were found for the SS-AD samples. This result is not surprising because distinct differences in the relative abundance of these phyla were observed with various operating parameters. Firmicutes and Bacteroidetes have been repeatedly reported as the main phyla in different anaerobic digesters [40]. In this study, Firmicutes sequences indicated that it was the most predominant phylum at temperatures of 50°C and 60°C, accounting for 65-90% of the total bacterial sequences; the percentages of Firmicutes sequences in the SS-AD samples were 37.5-60% at 40°C, except for S7 (27%). Bacteroidetes was the second most prevalent phylum at 40°C (18.62-28.37%, except for S7), but it only represented 0.76-12.21% of the total bacterial sequences at 50 and 60°C. These observations of a higher abundance of Firmicutes and a lower abundance of Bacteroidetes at the process temperatures of 50-60°C compared with 40°C are consistent with the results from previous studies [41, 42], indicating a competitive advantage of Firmicutes over Bacteroidetes at elevated temperatures [40]. For the phylum Thermotogae, the percentage of sequences at 60°C (2.07-5.45%) is much higher than that at other temperatures (0.15-1.29%), except for S12 (2.85%). Due to the SS-AD failure, the major bacterial phyla of S7 were dramatically different from those of other samples at 40°C (Figure 4(a)), containing a lower percentage of Firmicutes sequences and Bacteroidetes sequences and a much higher percentage of Proteobacteria sequences. It also noted that S11, with excessive acidification, contained a higher percentage of Proteobacteria, Aminicenantes, Actinobacteria, and Nitrospirae sequences and a lower percentage of Firmicutes sequences than the other samples at 50°C.

A total of 18 classes were identified for SS-AD samples that harboured ≥1% of the reads in one or more of the sequences, while Clostridia, Bacteroidia, Anaerolineae, and OPB54 were the primary communities (Figure 4(b)). Among them, the class Clostridia has been associated with hydrolysis, acidogenesis, and acetogenesis steps [40]. OPB54 was previously identified in an enrichment culture of lignocellulosic biomass and was the most abundant anaerobic syntrophic acetate-oxidizing genus in biogas digesters fed with high levels of acetate [43, 44]. The difference between the S13 and S14 samples, which have identical operating parameters, was quite small at the class level, where OPB54_norank in the phylum Firmicutes was the most dominant genus (Figure S2). It is worth noting that the biogas production values and relative abundances of OPB54 and Bacteroidia after 20 d of SS-AD can be fitted well using a quadratic model (Figure 4(c)), with , implying that OPB54 and Bacteroidia play important roles in the methanogenic metabolism for agriculture waste thermophilic SS-AD.

4. Conclusion

Optimizing the process parameters, i.e., temperature (40-60°C), initial solid content (17.5-32.5%), and C/N ratio (15-32 : 1), is important to promote the thermophilic SS-AD performance of the agriculture waste. All the factors, including interactive terms (except the ISC), were significant in the quadratic model for biogas production. Among the three operating parameters, the C/N ratio had the largest effect on biogas production, followed by temperature, and the maximum biogas yield of 241.4 mL gVS^-1 could be achieved at 47.3°C, , and . After 20 d of SS-AD, PCoA showed a distinct community structure that could be separated into three groups based on incubation temperatures, except for the SS-AD sample with excessive acidification. The biogas production values and relative abundance of OPB54 and Bacteroidia after 20 d of SS-AD can be fitted well using a quadratic model, implying that OPB54 and Bacteroidia play important roles in the methanogenic metabolism.

Data Availability

The data used to support the findings of this study are available from the corresponding author upon request.

Disclosure

The funding sources had no role in the study design, data collection, and analysis, decision to publish, or preparation of the manuscript.

Conflicts of Interest

There are no conflicts to declare.

Acknowledgments

The authors wish to thank the Basal Research Fund of Central Public-interest Scientific Institution of Nanjing Institute of Environmental Sciences, Ministry of Ecology and Environment (No. GYZX190203 and No. 20160301), the Distinguished Professor in Universities of Shanghai (Oriental Scholar, No. TP2017041), and the National Key Research and Development Program of China (2016YFD0800601).

Supplementary Materials

Figure S1: SS-AD reactor used in this study. Figure S2: major bacterial genera (a list of the 50 most abundant genera) after 20 d of SS-AD. (Supplementary materials)

References

J. Chen, Y. Gong, S. Wang, B. Guan, J. Balkovic, and F. Kraxner, “To burn or retain crop residues on croplands? An integrated analysis of crop residue management in China,” Science of The Total Environment, vol. 662, pp. 141–150, 2019.
View at: Publisher Site | Google Scholar
Y. R. Fang, Y. Wu, and G. H. Xie, “Crop residue utilizations and potential for bioethanol production in China,” Renewable and Sustainable Energy Reviews, vol. 113, article 109288, 2019.
View at: Publisher Site | Google Scholar
W. Bao, Y. Yang, T. Fu, and G. H. Xie, “Estimation of livestock excrement and its biogas production potential in China,” Journal of Cleaner Production, vol. 229, pp. 1158–1166, 2019.
View at: Publisher Site | Google Scholar
G. Capson-Tojo, R. Moscoviz, S. Astals, Á. Robles, and J. P. Steyer, “Unraveling the literature chaos around free ammonia inhibition in anaerobic digestion,” Renewable and Sustainable Energy Reviews, vol. 117, article 109487, 2020.
View at: Publisher Site | Google Scholar
Z.-B. Yue, W.-W. Li, and H.-Q. Yu, “Application of rumen microorganisms for anaerobic bioconversion of lignocellulosic biomass,” Bioresource Technology, vol. 128, pp. 738–744, 2013.
View at: Publisher Site | Google Scholar
M. R. Riazi and D. Chiaramonti, Biofuels Production and Processing Technology, CRC Press, 2017.
View at: Publisher Site
E. Rouches, R. Escudié, E. Latrille, and H. Carrère, “Solid-state anaerobic digestion of wheat straw: impact of S/I ratio and pilot-scale fungal pretreatment,” Waste Management, vol. 85, pp. 464–476, 2019.
View at: Publisher Site | Google Scholar
Z. Yan, Z. Song, D. Li, Y. Yuan, X. Liu, and T. Zheng, “The effects of initial substrate concentration, C/N ratio, and temperature on solid-state anaerobic digestion from composting rice straw,” Bioresource Technology, vol. 177, pp. 266–273, 2015.
View at: Publisher Site | Google Scholar
X. Ge, F. Xu, and Y. Li, “Solid-state anaerobic digestion of lignocellulosic biomass: recent progress and perspectives,” Bioresource Technology, vol. 205, pp. 239–249, 2016.
View at: Publisher Site | Google Scholar
Y. Li, S. Y. Park, and J. Zhu, “Solid-state anaerobic digestion for methane production from organic waste,” Renewable and Sustainable Energy Reviews, vol. 15, no. 1, pp. 821–826, 2011.
View at: Publisher Site | Google Scholar
Y. Liu, J. Fang, X. Tong et al., “Change to biogas production in solid-state anaerobic digestion using rice straw as substrates at different temperatures,” Bioresource Technology, vol. 293, article 122066, 2019.
View at: Publisher Site | Google Scholar
T. Pincam, H. Brix, and A. Jampeetong, “Treatment of anaerobic digester effluent using Acorus calamus: effects on plant growth and tissue composition,” Plants, vol. 7, no. 2, p. 36, 2018.
View at: Publisher Site | Google Scholar
Q. Shui, H. Dong, Z. Zhu, and H. Huang, “Present status of biogas effluent treatment technology research and application (in Chinese),” Journal of Agricultural Science and Technology, vol. 13, pp. 83–87, 2011.
View at: Google Scholar
SEPA, Standards for Irrigation Water Quality of China, Beijing, China, 2005.
R. Le Hyaric, H. Benbelkacem, J. Bollon, R. Bayard, R. Escudie, and P. Buffiere, “Influence of moisture content on the specific methanogenic activity of dry mesophilic municipal solid waste digestate,” Journal of Chemical Technology and Biotechnology, vol. 87, no. 7, pp. 1032–1035, 2012.
View at: Publisher Site | Google Scholar
A. Abbassi-Guendouz, D. Brockmann, E. Trably et al., “Total solids content drives high solid anaerobic digestion via mass transfer limitation,” Bioresource Technology, vol. 111, pp. 55–61, 2012.
View at: Publisher Site | Google Scholar
J. Fernandez, M. Perez, and L. I. Romero, “Effect of substrate concentration on dry mesophilic anaerobic digestion of organic fraction of municipal solid waste (OFMSW),” Bioresource Technology, vol. 99, no. 14, pp. 6075–6080, 2008.
View at: Publisher Site | Google Scholar
X. Wang, X. Lu, F. Li, and G. Yang, “Effects of temperature and carbon-nitrogen (C/N) ratio on the performance of anaerobic co-digestion of dairy manure, chicken manure and rice straw: focusing on ammonia inhibition,” PLoS One, vol. 9, no. 5, article e97265, 2014.
View at: Publisher Site | Google Scholar
J. Fernández-Rodríguez, M. Pérez, and L. I. Romero, “Comparison of mesophilic and thermophilic dry anaerobic digestion of OFMSW: kinetic analysis,” Chemical Engineering Journal., vol. 232, pp. 59–64, 2013.
View at: Publisher Site | Google Scholar
S. Steudler, A. Werner, and J. J. Cheng, Solid State Fermentation Research and Industrial Applications, Springer International Publishing, 2019.
View at: Publisher Site
D. Brown and Y. Li, “Solid state anaerobic co-digestion of yard waste and food waste for biogas production,” Bioresource Technology, vol. 127, pp. 275–280, 2013.
View at: Publisher Site | Google Scholar
P. D. Schloss, S. L. Westcott, T. Ryabin et al., “Introducing mothur: open-source, platform-independent, community-supported software for describing and comparing microbial communities,” Applied and Environmental Microbiology, vol. 75, no. 23, pp. 7537–7541, 2009.
View at: Publisher Site | Google Scholar
R. Rajagopal, D. I. Massé, and G. Singh, “A critical review on inhibition of anaerobic digestion process by excess ammonia,” Bioresource Technology, vol. 143, pp. 632–641, 2013.
View at: Publisher Site | Google Scholar
Z. Wang, F. Xu, and Y. Li, “Effects of total ammonia nitrogen concentration on solid-state anaerobic digestion of corn stover,” Bioresource Technology, vol. 144, pp. 281–287, 2013.
View at: Publisher Site | Google Scholar
G. Bitton, Wastewater Microbiology, John Wiley & Sons Inc., Hoboken, NJ, USA, 2005.
View at: Publisher Site
T. Müller, B. Walter, A. Wirtz, and A. Burkovski, “Ammonium toxicity in bacteria,” Current Microbiology, vol. 52, no. 5, pp. 400–406, 2006.
View at: Publisher Site | Google Scholar
T. Sayara and A. Sánchez, “A review on anaerobic digestion of Lignocellulosic wastes: pretreatments and operational conditions,” Applied Sciences, vol. 9, no. 21, article 4655, 2019.
View at: Publisher Site | Google Scholar
O. Yenigün and B. Demirel, “Ammonia inhibition in anaerobic digestion: a review,” Process Biochemistry, vol. 48, no. 5-6, pp. 901–911, 2013.
View at: Publisher Site | Google Scholar
Z. Guangyin and Z. Youcai, “Enhanced sewage sludge dewaterability by chemical conditioning,” in Pollution Control and Resource Recovery for Sewage Sludge, Z. Guangyin and Z. Youcai, Eds., pp. 13–99, Butterworth-Heinemann, 2017.
View at: Publisher Site | Google Scholar
J. Bollon, H. Benbelkacem, R. Gourdon, and P. Buffière, “Measurement of diffusion coefficients in dry anaerobic digestion media,” Chemical Engineering Science, vol. 89, pp. 115–119, 2013.
View at: Publisher Site | Google Scholar
X. Li, X. Dai, J. Takahashi et al., “New insight into chemical changes of dissolved organic matter during anaerobic digestion of dewatered sewage sludge using EEM-PARAFAC and two-dimensional FTIR correlation spectroscopy,” Bioresource Technology, vol. 159, pp. 412–420, 2014.
View at: Publisher Site | Google Scholar
S. Shakeri Yekta, M. Gonsior, P. Schmitt-Kopplin, and B. H. Svensson, “Characterization of dissolved organic matter in full scale continuous stirred tank biogas reactors using ultrahigh resolution mass spectrometry: a qualitative overview,” Environmental Science & Technology, vol. 46, no. 22, pp. 12711–12719, 2012.
View at: Publisher Site | Google Scholar
M. Xing, X. Li, J. Yang, Z. Huang, and Y. Lu, “Changes in the chemical characteristics of water-extracted organic matter from vermicomposting of sewage sludge and cow dung,” Journal of Hazardous Materials, vol. 205-206, pp. 24–31, 2012.
View at: Publisher Site | Google Scholar
J. Yi, B. Dong, J. Jin, and X. Dai, “Effect of increasing total solids contents on anaerobic digestion of food waste under mesophilic conditions: performance and microbial characteristics analysis,” PLoS One, vol. 9, no. 7, article e102548, 2014.
View at: Publisher Site | Google Scholar
K. Paritosh, N. Pareek, A. Chawade, and V. Vivekanand, “Prioritization of solid concentration and temperature for solid state anaerobic digestion of pearl millet straw employing multi-criteria assessment tool,” Scientific Reports, vol. 9, no. 1, article 11902, 2019.
View at: Publisher Site | Google Scholar
J. Shi, Z. Wang, J. A. Stiverson, Z. Yu, and Y. Li, “Reactor performance and microbial community dynamics during solid-state anaerobic digestion of corn stover at mesophilic and thermophilic conditions,” Bioresource Technology, vol. 136, pp. 574–581, 2013.
View at: Publisher Site | Google Scholar
V. Marchioro, R. L. R. Steinmetz, A. C. do Amaral, T. C. Gaspareto, H. Treichel, and A. Kunz, “Poultry litter solid state anaerobic digestion: effect of digestate recirculation intervals and substrate/inoculum ratios on process efficiency,” Frontiers in Sustainable Food Systems, vol. 2, 2018.
View at: Publisher Site | Google Scholar
M. A. Bustamante, A. P. Restrepo, J. A. Alburquerque et al., “Recycling of anaerobic digestates by composting: effect of the bulking agent used,” Journal of Cleaner Production, vol. 47, pp. 61–69, 2013.
View at: Publisher Site | Google Scholar
A. Torres-Climent, J. Martin-Mata, F. Marhuenda-Egea et al., “Composting of the solid phase of digestate from biogas production: optimization of the moisture, C/N ratio, and pH conditions,” Communications in Soil Science and Plant Analysis, vol. 46, Supplement 1, pp. 197–207, 2015.
View at: Publisher Site | Google Scholar
D. G. Mulat, S. G. Huerta, D. Kalyani, and S. J. Horn, “Enhancing methane production from lignocellulosic biomass by combined steam-explosion pretreatment and bioaugmentation with cellulolytic bacterium Caldicellulosiruptor bescii,” Biotechnology for Biofuels, vol. 11, no. 1, p. 19, 2018.
View at: Publisher Site | Google Scholar
Y. F. Li, M. C. Nelson, P. H. Chen, J. Graf, Y. Li, and Z. Yu, “Comparison of the microbial communities in solid-state anaerobic digestion (SS-AD) reactors operated at mesophilic and thermophilic temperatures,” Applied Microbiology and Biotechnology, vol. 99, no. 2, pp. 969–980, 2015.
View at: Publisher Site | Google Scholar
L. Sun, P. B. Pope, V. G. H. Eijsink, and A. Schnürer, “Characterization of microbial community structure during continuous anaerobic digestion of straw and cow manure,” Microbial Biotechnology, vol. 8, no. 5, pp. 815–827, 2015.
View at: Publisher Site | Google Scholar
L. Hao, F. Lü, L. Mazéas et al., “Stable isotope probing of acetate fed anaerobic batch incubations shows a partial resistance of acetoclastic methanogenesis catalyzed by Methanosarcina to sudden increase of ammonia level,” Water Research, vol. 69, pp. 90–99, 2015.
View at: Publisher Site | Google Scholar
M. T. Wong, W. Wang, M. Lacourt, M. Couturier, E. A. Edwards, and E. R. Master, “Substrate-driven convergence of the microbial community in lignocellulose-amended enrichments of gut microflora from the Canadian beaver (Castor canadensis) and north American moose (Alces americanus),” Frontiers in Microbiology, vol. 7, p. 961, 2016.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2020 Lianghu Su et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1527

Downloads

1265

Citations