The paper discusses a method for measuring changes in the electric resistance of a unidirectional carbon-fiber-reinforced plastic (CFRP) to detect an internal delamination. A numerical solution was obtained by the four-probe method for measuring the electric resistance. The influence of distance between electrodes on the efficiency of delamination detection was investigated. The problem was solved by the method of planning of experiments and constructing a surface response by using a 2D finite-element model. The distance between electrodes and the length of delamination were selected as parameters of the study. Distances between the internal and external electrodes for an effective detection of delaminations are determined.
Similar content being viewed by others
References
S. Gholizadeh, “A review of non-destructive testing methods of composite materials,” Procedia Structural Integrity, 1, 50–57 (2016).
K. Schulte and C. Baron, “Load and failure analyses of CFRP laminates by means of electrical resistivity measurements,” Comput. Sci. Technol., 36, No. 1, 63–76 (1989).
X. Wang and D. D. Chung, “Self-monitoring of fatigue defect and dynamic strain in carbon fiber polymer-matrix composite,” Composites Pt. B, 29, No. 1, 63–76 (1998).
J. C. Abry, S. Bochard, A. Chateauminois, M. Salvia, and E. G. Giraud, “In situ detection of defect in CFRP laminates by electric resistance measurements,” Compos. Sci. Technol., 59, No. 6, 925–935 (1999).
D. D. Chung, “Structural health monitoring by electric resistance measurement,” Smart Mater. Struct., 10, No. 4, 624–636 (2001).
S. Wang and D. D. L. Chung, “Piezoresistivity in continuous carbon fiber polymer-matrix,” Polym. Compos., 21, No. 1, 13–19 (2000).
A. Todoroki, “The effect of number of electrodes and diagnostic tool for monitoring the delamination of CFRP laminates by changes in electric resistance,” Compos. Sci. Technol., 61, No. 13, 1871–1880 (2001).
A. Todoroki, M. Tanaka, and Y. Shimamura, “Measurement of orthotropic electrical conductance of CFRP laminates and analysis of the effect on delamination monitoring with electric resistance change method,” Compos. Sci. Technol., 62, No. 5, 619–628 (2002).
A. Todoroki and Y. Tanaka, “Delamination identification of cross-ply graphite/epoxy composite beams using electric resistance change method,” Compos. Sci. Technol., 62, No. 5, 629–639 (2002).
A. Todoroki, M. Tanaka, and Y. Shimamura, “Delamination monitoring of graphite/epoxy laminated composite plate of electric resistance change method,” Compos. Sci. Technol., 62, No. 9, 1151–1160 (2002).
A. Todoroki, M. Tanaka, and Y. Shimamura, “High performance estimations of delamination of graphite/epoxy laminates with electric resistance change method,” Compos. Sci. Technol., 63, No. 13, 1911–1920 (2003).
J. B. Park, Okabe T. and N. Takeda, “New concept for modeling the electromechanical behavior of unidirectional carbon-fiber-reinforced plastic under tensile loading,” Smart Mater. Struct., 12, No. 1, 105–114 (2003).
A. Todoroki, Tanaka M., and Shimamura Y. “Multi-probe electric potential change method for delamination monitoring of graphite/epoxy composite plates using normalized response surface,” Compos. Sci. Technol., 64, No. 5, 749–758 (2004).
A. Todoroki, M. Tanaka, and Y. Shimamura. “Electric resistance change method for monitoring delaminations of CFRP laminates: effect of spacing between electrodes,” Compos. Sci. Technol., 65, No. 1, 37–46 (2005).
A. Iwasaki and A. Todoroki, “Statistical evaluation of modified electric resistance change method for delamination monitoring of CFRP plate,” Structural Health Monitoring, 4, No. 2, 119–136 (2005).
A. Todoroki, M. Ueda, and Y. Hirano, “Strain and defect monitoring of CFRP laminates by means of electric resistance measurement. (Review paper),” J. Solid Mech. and Mater. Eng., 1, No. 8, 947−969 (2007).
A. Todoroki, “Optimization-Based Monitoring of Laminated CFRP composites using Electric resistance Changes,” Final Report: FA4869-08-1-4031, Tokyo Institute of Technology, (2009).
J. Wen, Z. Xia, and E. F. Choy, “Defect detection of carbon fiber reinforced polymer composites via electric resistance measurement,” Composites Pt. B., 42, No. 1, 77−86 (2011).
M. Zappalorto, F. Panozzo, P. A. Carraro, and M. Quaresimin, “Electrical response of a laminate with a delamination: modelling and experiments,” Compos. Sci. Technol., 143, 31–45 (2017).
F. Panozzo, M. Zappalorto, L. Maragonia, S.K. Nothdurfter, A. Rullo and M. Quaresimin. “Modelling the electric resistance change in a multidirectional laminate with a delamination,” Compos. Sci. Technol., 162, 225–234 (2018).
F. Panozzo, M. Zappalorto, P.A. Carraro, and M. Quaresimin, “Electric resistance change vs defect state in cracked symmetric laminates: a closed for solution,” Compos. Sci. Technol., 184, 1081–1091 (2018).
V. Eglajs, “Approximation of data by the multi-dimensional equation of regression,” Problems of Dynamics and Strength, 39, 120–125 (1981).
Acknowledgments
This work was supported by the Riga Technical University through the Scientific Research Project Competition for Young Researchers No. ZP-2017/9.
Author information
Authors and Affiliations
Corresponding author
Additional information
Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 55, No. 6, pp. 1173-1184, November-December, 2019.
Rights and permissions
About this article
Cite this article
Kovaļovs, A., Ručevskis, S., Kulakov, V. et al. Optimum Position of Electrodes to Detect Delaminations in Composite Materials Using the Electric Resistance Change Method. Mech Compos Mater 55, 811–818 (2020). https://doi.org/10.1007/s11029-020-09852-y
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11029-020-09852-y