Abstract
The effect of the technological heredity of the stress–strain state on the accuracy and dimensional stability of nonrigid parts such as shafts is considered. The negative inheritable factors and patterns of inheritance of the stress–strain state of blanks are defined. An improved process of fabrication of nonrigid shafts is presented taking into account the technological heredity.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
REFERENCES
Veprev, A.A. and Pashkov, A.E., Complex technology of the aircraft panels forming, J. UAMFO, 2012, vol. 4, no. 1, p. 39.
Citti, P., Giorgetti, A., and Millefanti, U., Current challenges in material choice for high-performance engine crankshaft, in Proceedings of the International Conference on Stress Analysis, AIAS, Pisa, Italy,2017, p. 486.
Muratkin, G.V. and Kotova, I.V., Criteria for bending stiffness of rod parts, Remont, Vosstan., Moderniz., 2006, no. 2, p. 42.
Ovseenko, A.N., Technological residual deformations of non-rigid parts and methods for their reduction, Vestn. Mashinostr., 1991, no. 2, p. 58.
Kolker, Ya.D., Matematicheskii analiz tochnosti mekhanicheskoi obrabotki detalei (Mathematical Analysis of the Accuracy of Machining Parts), Kiev: Tekhnika, 1976, p. 200.
Muratkin, G.V., The formation of technological residual deformations and stresses in the manufacture of non-rigid shafts, Avtomatiz. Sovrem. Tekhnol., 2003, no. 8, p. 16.
Podzei, A.V., Tekhnologicheskie ostatochnye napryazheniya (Technological Residual Stresses), Moscow: Mashinostroenie, 1978, p. 216.
Suslov, A.G. and Dal’skii, A.M., Nauchnye osnovy tekhnologii mashinostroeniya (Scientific Foundations of Engineering Technology), Moscow: Mashinostroenie, 2002, p. 684.
Kotsyubinskii, O.Yu., Stabilizatsiya razmerov chugunnykh otlivok (Size Stabilization of Iron Castings), Moscow: Mashinostroenie, 1974, p. 296.
Termicheskaya obrabotka v mashinostroenii: Spravochnik (Heat Treatment in Engineering: A Handbook), Lakhtin, Yu.M. and Rakhshtadt, A.G., Eds., Moscow: Mashinostroenie, 1980, p. 783.
Yashcheritsyn, P.I., Ryzhov, E.V., and Averchenkov, V.I., Tekhnologicheskaya nasledstvennost' v mashinostroenii (Technological Inheritance in Mechanical Engineering), Minsk: Nauka Tekhnika, 1977, p. 256.
Muratkin, G.V., Editing non-rigid parts during heat treatment, Remont, Vosstan., Moderniz., 2004, no. 8, p. 21.
Asi, O. and Can, A.C., The comparison of the residual stresses between carburized and only quenched steels, Pamukkale Univ. J. Eng. Sci., 2001, no. 7, p. 182.
Mahmoudi, A.H., Ghasemi, A., and Farrahi, G.H., Sherafatnia, K., A comprehensive experimental and numerical study on redistribution of residual stresses by shot peening, J. Mater. Des., 2016, no. 90, p. 478.
Zaides, S.A. and Muratkin, G.V., Uprochnenie, vosstanovlenie, pravka valov: Uchebn. posobie (Hardening, Restoration, Dressing of Shafts, The School-Book), Irkutsk: IrGTU, 2005, p. 336.
Muratkin, G.V., Sarafanova, V.A., and Suvorov, M.O., Improving on relaxation resistance of material by surface plastic straining methods, Tekhnol. Met., 2017, no. 7, p. 19.
Muratkin, G.V., Investigation of the dressing method effect, Metalloobrabotka, 2014, no. 4 (82), p. 37.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
The authors declare that they have no conflict of interest.
Additional information
Translated by M. Kromin
About this article
Cite this article
Muratkin, G.V., Sarafanova, V.A. The Effect of the Technological Heredity of the Stress–Strain State on the Accuracy of Nonrigid Parts. J. Mach. Manuf. Reliab. 49, 45–50 (2020). https://doi.org/10.3103/S1052618820010094
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1052618820010094