Skip to main content
SpringerLink
Log in

Yield Strength Evaluation of Dissimilar Components of Layered Steel/Steel Composite by Kinetic Indentation

  • Published:
Journal of Materials Engineering and Performance Aims and scope Submit manuscript

Abstract

In the present study, values of yield strength of individual layers of layered composites based on different strength mild steels obtained by explosion welding followed by cold rolling and heat treatment were determined. The effect of cold rolling with a total reduction of 50% and heat treatment at a temperature of 500 °C on the change of the deformational resistance of Fe-2Mn-Si and Fe-11Cr-9Ni-2Mo-1Ti steels’ layers in the composite was established. It was shown that additional cold deformation of the layered composite leads to an increase in yield strength of Fe-2Mn-Si and Fe-11Cr-9Ni-2Mo-1Ti steels’ layers by 20% and 24%, respectively, and additional heat treatment of the cold-deformed composite contributes to strengthening of the Fe-11Cr-9Ni-2Mo-1Ti steel layers by 17% and softening of the Fe-2Mn-Si steel layers by 6%. It was shown that the level of strengthening of the Fe-11Cr-9Ni-2Mo-1Ti steel layers after cold rolling corresponds to the level of strengthening of this steel after heat treatment. It was determined that the maraging steel layers with initial ultrafine-grained microstructure are intensely strengthened (35%) by conducting combined heat-deformational processing of a layered composite, including cold rolling with a total reduction of 50% and subsequent heat treatment at a temperature of 500 °C.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5

Similar content being viewed by others

References

  1. D.D.L. Chung, Composite Materials: Science and Application, 2nd ed., B. Derby, Ed., Springer, Berlin, 2010, p 5–27

    Chapter  Google Scholar 

  2. K.N. Chawla, Composite Materials Science and Engineering, The University of Alabama at Birmingham, 2019, p 557

  3. S.V. Gladkovsky, S.V. Kuteneva, I.S. Kamantsev, S.N. Sergeev, and I.M. Safarov, Effect of Plastic Deformation on the Structure and Mechanical Properties of an Ultra-Low Carbon Interstitial-Free Steel in the Monolithic State and in the Composition of a Sandwich Composite, Phys. Met. Metallogr., 2016, 117, p 1070–1077 (in English)

    Article  CAS  Google Scholar 

  4. M. Randall, Particulate Composites: Fundamentals and Applications, Springer, Berlin, 2016, p 98

    Google Scholar 

  5. T.A. Venkatesh, K.J. Van Vliet, A.E. Giannakopoulos, and S. Suresh, Determination of Elasto-Plastic Properties by Instrumented Sharp Indentation: Guidelines for Property Extraction, Scr. Mater., 2000, 42, p 833–839 (in English)

    Article  CAS  Google Scholar 

  6. J.L. Bucaille, S. Stauss, E. Felder, and J. Michler, Determination of Plastic Properties of Metals by Instrumented Indentation Using Different Sharp Indenters, Acta Mater., 2003, 51, p 1663–1678 (in English)

    Article  CAS  Google Scholar 

  7. D.A. Konovalov, S.V. Smirnov, and A.V. Konovalov, Determination of Metal Strain-Hardening Curves from Conical-Indenter Impression Results, Russ. J. Nondestruct., 2008, 44, p 847–853 (in English)

    Article  CAS  Google Scholar 

  8. D.A. Konovalov, I.A. Golubkova, and S.V. Smirnov, Determining the Strength Properties of Individual Layers of Strained Laminated Composites by Kinetic Indentation, Russ. J. Nondestruct., 2011, 47, p 852–857 (in English)

    Article  Google Scholar 

  9. Y.P. Trykov, L.M. Gurevich, V.G. Shmorgunov, Sloistyye kompozity na osnove alyuminiya i yego splavov (Layered composites based on aluminum and its alloys), Metallurgiya, 2004, p 230 (in Russia)

  10. V.S. Lozhkin, E.A. Lozhkina, V.I. Mali, and M.A. Esikov, Structure and Mechanical Properties of Multilayered Composite Material, Formed by Explosive Welding of Steel 12X18H10T and Steel H18К9M5T Thin Plates, Obrabotka Metallov, 2014, 3(64), p 28–36 (in Russia)

    Google Scholar 

  11. V.S. Lozhkin, Structure and Mechanical Properties of Multilayered Composite Material, Formed by Explosive Welding of Steel 12X18H10T and Steel H18К9M5T Thin Plates, Obrabotka Metallov, 2013, 3(60), p 110–114 (in Russia)

    Google Scholar 

  12. I.M. Safarov, A.V. Korznikov, R.M. Galeyev, S.N. Sergeev, S.V. Gladkovsky, D.I. Dvoynikov, and IYu Litovchenko, The Ultrafine-Grained Structure, Texture and Mechanical Properties of Low Carbon Steel Obtained by Various Methods of Plastic Deformation, Lett. Mater., 2016, 6(2), p 126–131 (in English)

    Article  Google Scholar 

  13. V.I. Mali, I.A. Bataev, A.A. Bataev, D.V. Pavlyukova, E.A. Prikhodko, and M.A. Esikov, Geometric Transformations of Sheet Steel Billets in Explosion Welding of Multiple Sandwiches, Phys. Mesomech., 2011, 14, p 117–124 (in English)

    CAS  Google Scholar 

  14. E.W. Andrews, A.E. Giannakopoulos, E. Plisson, and S. Suresh, Analysis of the Impact of a Sharp Indenter, Int. J. Solids Struct., 2002, 39, p 281–295 (in English)

    Article  Google Scholar 

  15. N. Chollacoop, M. Dao, and S. Suresh, Depth-Sensing Instrumented Indentation with Dual Sharp Indenters, Acta Mater., 2003, 51, p 3713–3729 (in English)

    Article  CAS  Google Scholar 

  16. M. Dao, N. Chollacoop, K.J. Van Vliet, T.A. Venkatesh, and S. Suresh, Computational Modeling of the Forward and Reverse Problems in Instrumented Sharp Indentation, Acta Mater., 2001, 49, p 3899–3918 (in English)

    Article  CAS  Google Scholar 

  17. G. Care and A.C. Fisher-Cripps, Elastic-Plastic Indentation Stress Fields Using the Finite-Element Method, J. Mater. Sci., 1997, 32, p 5653–5659 (in English)

    Article  CAS  Google Scholar 

  18. R. Vaidyanathan, M. Dao, G. Ravichandran, and S. Suresh, Study of Mechanical Deformation in Bulk Metallic Glass Through Instrumented Indentation, Acta Mater., 2001, 49, p 3781–3789 (in English)

    Article  CAS  Google Scholar 

  19. S.V. Smirnov and V.P. Shvejkin, Method of Determination of Diagrams of Strengthening for Individual Structural Constituents in Multicomponent Systems, Phys. Met. Metallogr., 1995, 80, p 145–151 (in English)

    CAS  Google Scholar 

  20. M.B. Bakirov, M.A. Zaitsev, and I.V. Frolov, Mathematical Simulation of the Indentation Process of a Sphere into an Elastoplastic Half-Space, Diagnost. Mater., 2001, 67, p 37–47 (in English)

    Google Scholar 

  21. A.N. Tikhonov, V.Ya. Arsenin, Metody resheniya nekorrektnykh zadach (Solution of Ill-Posed Problems), 3rd ed., Nauka, 1986, p 76–102 (in Russia)

  22. T.I. Tabatchikova, I.L. Yakovleva, S.Y. Delgado Reina, and A.I. Plokhikh, Effect of Cyclic Treatment on the Formation of a Fragmented Structure in a Sparingly Alloyed Martensitic Steel, Phys. Met. Metallogr., 2016, 117, p 1123–1228 (in English)

    Article  CAS  Google Scholar 

  23. M.D. Perkas and V.M. Kardonskii, Vysokoprochnye martensitno-stareyushchie stali (High-Strength Maraging Steels), Metallurgiya, 1970, p 224 (in Russia)

  24. S.V. Gladkovsky, S.V. Kuteneva, I.S. Kamantsev, R.M. Galeev, and D.A. Dvoynikov, Formation of the Mechanical Properties and Fracture Resistance Characteristics of Sandwich Composites Based on the 09G2S Steel and the EP678 High-Strength Steel of Various Dispersion, DREAM, 2017, 6, p 71–90 (in Russia)

    Article  Google Scholar 

Download references

Acknowledgments

The authors are grateful to V.I. Mali, PhD, for producing layered composites by explosion welding, R.M. Galeev, PhD, for deformational and heat processing of Fe-11Cr-9Ni-2Mo-1Ti steel sheet and I.S. Kamantsev for experimental assistance. The study was funded by the state assignment to the Institute of Engineering Science, Ural Branch of the Russian Academy of Sciences, No. AAAA-A18-118020790147-4, and the project of Ural Branch of the Russian Academy of Sciences, No. 18-9-1-20.

Author information

Authors and Affiliations

  1. Institute of Engineering Science, Ural Branch of Russian Academy of Sciences, 34 Komsomolskaya St., Ekaterinburg, Russian Federation, 620049

    S. V. Gladkovsky, D. A. Konovalov & S. V. Kuteneva

Authors
  1. S. V. Gladkovsky
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. D. A. Konovalov
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. S. V. Kuteneva
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to S. V. Kuteneva.

Ethics declarations

Conflict of interest

The authors have no conflicts of interest to declare.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Gladkovsky, S.V., Konovalov, D.A. & Kuteneva, S.V. Yield Strength Evaluation of Dissimilar Components of Layered Steel/Steel Composite by Kinetic Indentation. J. of Materi Eng and Perform 29, 5757–5763 (2020). https://doi.org/10.1007/s11665-020-05083-3

Download citation

  • Received:

  • Revised:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11665-020-05083-3

Keywords

Search

Navigation