Abstract
This paper proposes a method for rapid cladding of copper powder with aluminum. The optimal parameters (frequency and amplitude of oscillations) of the experimental setup and the dispersity and volume fraction of the interacting powders are determined. The most productive cladding mechanism is considered. Dependences of the coating thickness (from 5 to 25 μm) on copper particles on the temperature (18–600°C) and the time of heating (5–30 s) the powder mixture are determined. It is shown that the highest rates of the coating growth on copper particles and the formation of Al–Cu intermetallic compounds are achieved at the temperatures of Al and Cu recrystallization.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
REFERENCES
Lyul’ko, V.G., Shugai, K.K., Zhmailov, B.B., and Oleinikov, D.V., Thermal synthesis of disperse microcomposites in vibrating layer as a way of production of new generation functional powder materials, Vestn. Perm. Gos. Tekh. Univ., Probl. Sovrem. Mater. Tekhnol., 2005, vol. 11, pp. 35–51.
Meilakh, A.G., High-strength low-alloy powder steel with a composite structure, Steel Transl., 2009, vol. 39, no. 11, pp. 1035–1037.
Kontsevoi, Yu.V., Meilakh, A.G., Shubin, A.B., Pastukhov, E.A., Dolmatov, A.V., and Sipatov, I.S., Premixes production for synthesis of wear-resistant composite, J. Phys.: Conf. Ser., 2017, vol. 790, no. 1, art. ID 012022.
Gorbunov, P.Z. and Gal’, V.V., Advanced dispersion-strengthened composite materials, Proizvod.-Tekh. Opyt, 1993, nos. 1–2, pp. 81–84.
Sviridov, V.V., Vorob’eva, T.N., Gaevskaya, T.V., and Stepanova, L.I., Khimicheskoe osazhdenie metallov iz vodnykh rastvorov (Chemical Deposition of Metals from Aqueous Solutions), Minsk: Universitetskoe, 1987.
Klimenko, V.N., Napara-Volgina, S.G., and Kostyrko, L.N., N2M nickel-molybdenum steel based on partially alloyed powder, Powder Metall. Met. Ceram., 1995, vol. 33, nos. 1–2, pp. 29–32.
Vityaz’, A.P., Lovsheiko, F.G., and Lovsheiko, G.F., Mekhanicheski legirovannye splavy na osnove alyuminiya i medi (Mechanically Alloyed Alloys Based on Aluminum and Copper), Minsk: Belaruskaya Navuka, 1998.
Dorofeev, Yu.G., Sergeenko, S.N., and Chernoknizhnikov, S.Yu., Features of mechanochemical activation and consolidation of the powder system Fe–Al, Fiz. Khim. Obrab. Mater., 2004, no. 1, pp. 62–65.
Gerashchenkov, D.A., Farmakovskii, B.V., Samodelkin, E.A., and Gerashchenkova, E.Yu., Adhesive durability of the composite reinforced “metal–nonmetal” coatings produced by gas dynamic cold spray, Vopr. Materialoved., 2014, no. 2 (78), pp. 103–117.
Castanho, J.M. Vieira, M.T., Matos, M., and Trindade, B., Nanostructured coated powders for structural net shape components, J. Alloys Compd., 2007, vols. 434–435, pp. 383–385.
Bataev, I.A., Bataev, A.A., Golkovski, M.G., Krivezhenko, D.S., Losinskaya, A.A., and Lenivtseva, O.G., Structure of surface layers produced by non-vacuum electron beam boriding, Appl. Surf. Sci., 2013, vol. 284, pp. 472–481.
Krivezhenko, D.S., Drobyaz, E.A., Bataev, I.A., and Chuchkova, L.V., Investigation of the structure and properties of boron-containing coatings obtained by electron-beam treatment, AIP Conf. Proc., 2015, vol. 1683, no. 1, art. ID 020104.
Kontsevoi, Yu.V., Dolmatov, A.V., Pastukhov, E.A., and Grigor’eva, T.F., Mechanical cladding of dispersed Fe–Al and Fe–Cu systems under dynamic loads, Izv. VUZov, Poroshk. Metall. Funkts. Pokrytiya, 2015, no. 1, pp. 8–11.
Kontsevoi, Yu.V., Meilakh, A.G., Shubin, A.B., and Pastukhov, E.A., RF Patent 2629416, 2017.
Vatolin, N.A., Kontsevoi, Yu.V., and Tskhai, E.V., Interaction of steel strip and aluminum powder in the process of high-speed annealing after plastic deformation, Metally, 1997, no. 1, pp. 95–100
Moriyama, M. and Kajihara, M., Fast penetration of Cu/Ni/Cu diffusion couples due to diffusion induced recrystallization, ISIJ Int., 1998, vol. 38, no. 5, pp. 489–494.
Kontsevoi, Yu.V., Meilakh, A.G., Shubin, A.B., Pastukhov, E.A., and Sipatov, I.S., Impacts of deformation degree and heating rate on intensity of reactive diffusion in Fe–Al system, Materialy XX Mendeleevskogo s”ezda po Obshchei i prikladnoi khimii, Ekaterinburg, 26–30 sentyabrya 2016, Tezisy dokladov (Proc. XX Mendeleev Congress on General and Applied Chemistry, Yekaterinburg, September 26–30, 2016, Abstracts of Papers), Yekaterinburg: Ural. Otd., Ross. Akad. Nauk, 2016, vol. 3, p. 83.
Goldsmith, W., Impact: The Theory and Physical Behavior of Colliding Solids, London: E. Arnold, 1960.
Kontsevoi, Yu.V., Pastukhov, E.A., Ignat’ev, I.E., Bulanov, V.Ya., and Ignat’eva, E.V., Vibroaeratic mixing of the powders in a gas medium: Report 2. Computing kinematics of a valve and powder and determining optimum sizes of mixer elements, Russ. J. Non-Ferrous Met., 2009, vol. 50, pp. 507–512.
Targ, S.M., Kratkii kurs teoreticheskoi mekhaniki (A Short Course of Theoretical Mechanics), Moscow: Vysshaya Shkola, 1986.
Funding
This work was carried out as part of the State Assignment of the Institute of Metallurgy of the Ural Branch of the Russian Academy of Sciences using the equipment of the Shared Access Center Ural-M.
Author information
Authors and Affiliations
Corresponding authors
Ethics declarations
The authors declare that they have no conflicts of interest.
Additional information
Translated by K. Lazarev
Rights and permissions
About this article
Cite this article
Kontsevoi, Y.V., Meilakh, A.G. Vibration Cladding of Copper Powder with Aluminum. Inorg. Mater. Appl. Res. 11, 672–676 (2020). https://doi.org/10.1134/S2075113320030235
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S2075113320030235