Abstract
Formalization of the search for technological bases is considered in the machining of a slotted shaft. The ISG format is employed. The use of geometric information in IGS file format is analyzed. The following parameters are identified: the spatial position of a plane; its coordinates; the coordinates of its vertices, the configuration of the generatrices, and the edge positions.
This is a preview of subscription content, log in via an institution to check access.
We’re sorry, something doesn't seem to be working properly.
Please try refreshing the page. If that doesn't work, please contact support so we can address the problem.
REFERENCES
Ionov, M.V., Sul’din, S.P., Mitin, E.V., and Mitina, A.E., The description of geometric primitives using the intermediate IGS format, Materialy XXII Nauchno-prakticheskoi konferentsii molodykh uchenykh, aspirantov i studentov Natsional’nogo issledovatel’skogo Mordovskogo gosudarstvennogo universiteta im. N.P. Ogareva (Proc. XXII Sci.-Peact. Conf. of Young Scientists, Post-Graduate Students, and Undergraduate Students of the Ogarev Mordovia State University), Saransk, 2019, pp. 355–359.
Mitin, E.V., 3D modeling of automated choice of technological processes, Cand. Sci. (Eng.) Dissertation, Moscow: Moscow State Technol. Univ., 2005.
Starostin, V.G. and Lelyukhin, V.E., Formalizatsiya proektirovaniya protsessov obrabotki rezaniem (Formalization of Design of Cutting Processes), Moscow: Mashinostroenie, 1986.
Kuz’min, V.V., Skhirtladze, A.G., and Usov, S.V., Matematicheskoe modelirovanie tekhnologicheskikh protsessov v mashinostroenii (Mathematical Modeling of Technological Processes in Machine Engineering), Moscow: Slavyanskaya Shkola, 2002.
Mitin, E.V., Sul’din, S.P., and Okunev, D.V., Formalization of automated base selection in the design of machining processes, Stanki Instrum., 2018, no. 5, pp. 17–20.
Mitin, E.V., Sul’din, S.P., and Okunev, D.V., Formalization of automated base selection in the design of machining processes, Russ. Eng. Res., 2018, vol. 38, no. 11, pp. 886–888.
Kalyakulin, S.Yu., Kuz’min, V.V., Mitin, E.V., et al., Design of technological processes based on synthesis, Vestn. Mordovsk. Univ., 2018, vol. 28, no. 1, pp. 77–84.
Kalyakulin, S.Yu., Kuz’min, V.V., Mitin, E.V., and Sul’din, S.P., Informational relational models for calculating the cutting conditions in automatic control systems, Russ. Eng. Res., 2018, vol. 38, no. 12, pp. 1049–1052.
Kalyakulin, S.Yu., Mitin, E.V., Sul’din, S.P., and Kuz’min, V.V., Informational relational models for calculating the cutting conditions in automatic control system, Russ. Eng. Res., 2018, vol. 38, no. 12, pp. 1049–1052.
Mitin, E.V. and Sul’din, S.P., Hob strength in gear cutting, Russ. Eng. Res., 2018, vol. 38, no. 8, pp. 635–637.
Kalyakulin, S.Yu., Kuz’min, V.V., Mitin, E.V., et al., Development of a mathematical model of a part based on graphic systems models, Inzh. Tekhnol. Sist., 2019, vol. 29, no. 1, pp. 67–76.
Mitin, E.V., Sul’din, S.P., Grigor’ev, A.V., and Okunev, D.V., Design of helical drills with channels for coolant supply, Russ. Eng. Res., 2019, vol. 39, no. 6, pp. 520–522.
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated by B. Gilbert
About this article
Cite this article
Mitin, E.V., Sul’din, S.P. & Mitina, A.E. IGS-Based Selection of Technological Bases in Machining a Slotted Shaft. Russ. Engin. Res. 40, 700–703 (2020). https://doi.org/10.3103/S1068798X20080171
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X20080171