Skip to main content
SpringerLink
Log in

Analysis of Internal Stress in a Tape Subsrate Made of the AISI 310S Stainless Steel for the Second-Generation HTS Wires Using Neutron Stress Diffractometry

  • SOLID STATE
  • Published:
Technical Physics Aims and scope Submit manuscript

Abstract

Neutron stress diffractometry is used to study internal (residual) stress in a tape made of the AISI 310S stainless steel with a thickness of 100 μm and a width of 4 mm in three directions (along, across, and perpendicularly to the rolling plane). The residual macrostresses averaged over the tape length are determined at a segment of 40 cm. The macrostress distribution indicates a crescent-type deformation of the tape (bending in the rolling plane along the rolling direction). The correlation between macrostresses and internal microstresses is established (the stronger macrostresses, the higher concentration of the microstresses).

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
Fig. 5.
Fig. 6.

Similar content being viewed by others

REFERENCES

  1. E. P. Krasnoperov, V. V. Guryev, S. V. Shavkin, V. E. Krylov, V. V. Sychugov, V. S. Korotkov, A. V. Ovcharov, and P. V. Volkov, J. Eng. Sci. Technol. Rev. 12 (1), 104 (2019). https://doi.org/10.25103/jestr.121.12

    Article  Google Scholar 

  2. V. T. Em, I. D. Karpov, V. A. Somenkov, V. P. Glazkov, A. M. Balagurov, V. V. Sumin, P. Mikula, and J. Ŝaroun, Phys. B 551, 413 (2018). https://doi.org/10.1016/j.physb.2018.02.042

    Article  ADS  Google Scholar 

  3. P. J. Withers and H. K. D. H. Bhadeshia, Mater. Sci. Technol. 17, 355 (2001).

    Article  Google Scholar 

  4. ISO/TS 21432:2005 Non-Destructive Testing—Standard Test Method for Determining Residual Stresses by Neutron Diffraction. Technical Specification, 1st ed. (ISO, 2005).

  5. T. Hutchings, P. J. Withers, T. M. Holden, and T. Lorentzen, Introduction to the Characterization of Residual Stress by Neutron Diffraction, 1st ed. (CRC Press, Boca Raton, 2005).

    Book  Google Scholar 

  6. V. T. Em, A. M. Balagurov, V. P. Glazkov, I. D. Karpov, P. Mikula, N. F. Miron, V. A. Somenkov, V. V. Sumin, J. Šaroun, and M. N. Shushunov, Instrum. Exp. Tech. 60 (4), 526 (2017). https://doi.org/10.1134/S0020441217040042

    Article  Google Scholar 

  7. FullProf Suite, www.ill.eu/sites/fullprof/index.html (cited May 31, 2019).

  8. Stainless Steel (AISI 310S (S31008)), www.makeitfrom.com/material-properties/AISI-310S-S31008-Stainless-Steel (cited May 31, 2019).

  9. GOST 26877-2008: Metal Products. Methods for Measuring Shape Deviations (Standartinform, Moscow, 2013) [in Russian].

  10. http://tk-msi.bussola.ru/cms/ Klassy_serpovidnosti_stalnyh_polos (cited January 15, 2020).

Download references

Funding

This work was supported by the Ministry of Science and High Education of the Russian Federation (contract no. 14.604.21.0197, identification number RFMEFI60417X0197). Equipment of the “Neutron Research Complex Based on the IR-8 Reactor” was used in this work.

Author information

Authors and Affiliations

  1. National Research Center Kurchatov Institute, 123182, Moscow, Russia

    I. D. Karpov, A. V. Irodova, V. S. Kruglov, S. V. Shavkin & V. T. Em

Authors
  1. I. D. Karpov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. A. V. Irodova
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. V. S. Kruglov
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. S. V. Shavkin
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. V. T. Em
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to A. V. Irodova.

Ethics declarations

The authors declare that there is no conflicts of interest.

Additional information

Translated by A. Chikishev

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Karpov, I.D., Irodova, A.V., Kruglov, V.S. et al. Analysis of Internal Stress in a Tape Subsrate Made of the AISI 310S Stainless Steel for the Second-Generation HTS Wires Using Neutron Stress Diffractometry. Tech. Phys. 65, 1051–1057 (2020). https://doi.org/10.1134/S1063784220070063

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1134/S1063784220070063

Search

Navigation