Abstract
A method is proposed for the assembly of preloaded cylindrical joints on the basis of relative interchangeability. As shown in examples, this method permits the connection of shafts with a reparable defect and holes with an irreparable defect or the connection of shafts with an irreparable defect and holes with a reparable defect. By this method, the required joint accuracy with limiting preload is maintained.
Similar content being viewed by others
REFERENCES
Leonov, O.A. and Shkaruba, N.Zh., A parametric failure model for the calculation of the fit tolerance of joints with clearance, J. Frict. Wear, 2019, vol. 40, no. 4, pp. 332–336.
Bondareva, G.I., Changes to the standard of a unified tolerance and fitting system, Trakt. Sel’khozmash., 2016, no. 12, pp. 39–42.
Erohin, M., Leonov, O., Kataev, U., and Vergazova, U., Calculation of fits for cylindrical connections with key for reducers in agricultural machinery, Proc. 18th Int. Sci. Conf. “Engineering for Rural Development,” Jelgava, 2019, pp. 469–474.
Leonov, O.A., Vzaimozamenyaemost’ unifitsirovannykh soedinenii pri remonte sel’skokhozyaistvennoi tekhniki: Monografiya (Interchangeability of Unified Joints in Reparation of Agricultural Machines: Monograph), Moscow: Mosk. Gos. Agroinzh. Univ., 2003.
Erokhin, M.N., The relationship of accuracy and reliability of joints in the reparation of agricultural machines, Vestn. Mosk. Gos. Agroinzh. Univ., 2006, no. 2, pp. 22–25.
Antonova, U.Yu., The selective assembly of the cylinder-piston joint for small-scale repairation service, Innovatsii APK: Probl. Persp., 2019, no. 2, pp. 60–67.
Belov, V.M., Metrologiya, standartizatsiya, kvalimetriya. Standartizatsiya norm vzaimozamenyaemosti (Metrology, Standardization, and Qualimetry. Standardization of Interchangeability Standards), M.: Mosk. Gos. Agroinzh. Univ., 1999.
Vergazova, Yu.G., Calculation of fitting of joints with dowels for agricultural machines, Vestn. Mosk. Gos. Agroinzh. Univ., 2014, no. 2, pp. 13–15.
Antonova, U.Yu., Metrological control of cylinder liners for diesel engine reparation, Vestn. Baranovsk. Gos. Univ., Ser.: Tekh. Nauki, 2018, no. 6, pp. 104–109.
Bondareva, G.I., The influence of the measurement tool error on losses during the reparation of agricultural machines, Mekh. Elektrif. Sel’sk. Khoz., 2007, no. 11, pp. 27–29.
Bondareva, G.I., Input control and metrological support at technical service enterprises, Sel. Mekhanizator, 2017, no. 4, pp. 36–38.
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated by B. Gilbert
About this article
Cite this article
Erokhin, M.N., Leonov, O.A., Shkaruba, N.Z. et al. Assessing the Relative Interchangeability in Joints with Preload. Russ. Engin. Res. 40, 469–472 (2020). https://doi.org/10.3103/S1068798X2006009X
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X2006009X