Skip to main content
SpringerLink
Log in

Flow-induced Orientations of Fibers and Their Influences on Warpage and Mechanical Property in Injection Fiber Reinforced Plastic (FRP) Parts

  • Regular Paper
  • Published:
International Journal of Precision Engineering and Manufacturing-Green Technology Aims and scope Submit manuscript

Abstract

During the past two centuries, due to too fast growth of the human population, the pollution made by human has seriously impacts on our environment, particularly, for the CO2 emission. To diminish the CO2 emission problem, one of the effective solutions is applying lightweight material, such as the fiber-reinforced plastics (FRP), to replace metal in the manufacturing of transportation vehicles. However, since the reinforced function of the fibers inside plastic matrix is very complex, it is not easy to be visualized and managed. Specifically, the connection from microstructures of the fibers to the physical properties of the final product is far from our understanding. In this study, we have proposed a benchmark with three standard specimens based on ASTM D638 with different gate designs. This system is used to study the fiber microstructures and associated mechanical properties using numerical simulation and experimental studies. Results showed that the tensile properties (including tensile modulus and tensile stress) of all three ASTM standard specimens can be improved significantly in the appearance of the fibers. Moreover, the tensile properties variation of the finished parts associated with the microstructures of the short fibers based on the gate design have been also investigated. Specifically, the tensile modulus and the strength of the Model I are greater than that of Model II, while Model III is much less than others because of its double gate effect. The reason why the tensile modulus and the strength of the Model I is greater than that of Model II is due to some entrance effect. That entrance effect will further provide flow-induced fiber orientation to melt and then enhance the tensile properties of Model I. To confirm the observation, a series simulation and experimental studies have been performed. Specifically, the fiber orientation distribution is predicted using CAE, and verified using micro-CT scan and image analysis by Avizo software. Hence, the correlation from fiber microstructure feature (particularly in fiber orientation) to tensile modulus and tensile stress for fiber reinforced thermoplastic (FRP) in injection molding process can be validated.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19

Similar content being viewed by others

References

  1. M. Roser, “Two centuries of rapid global population growth will come to an end”, Web-source: https://ourworldindata.org/world-population-growth-past-future, Accessed 18 Aug 2019.

  2. Schmidt, C., Li, W., Thiede, S., Kara, S., & Herrmann, C. (2015). A methodology for customized prediction of energy consumption in manufacturing Industries. International Journal of Precision Engineering and Manufacturing-Green Technology, 2(2), 163–172.

    Article  Google Scholar 

  3. H. Ritchie and M. Roser, “CO2 and Greenhouse Gas Emissions”, Web-source: https://ourworldindata.org/co2-and-other-greenhouse-gas-emissions, Accessed 18 Aug 2018.

  4. EPA of USA, “Sources of Greenhouse Gas Emissions”, Web-source: https://www.epa.gov/ghgemissions/sources-greenhouse-gas-emissions, Accessed 18 Aug 2018.

  5. U. S. Department of Energy report, “Lightweight materials R & D Program”, 2013 Vehicle Technologies Office.

  6. “BMW i3 makes its world premiere”, Reinforced plastics, p. 7, Sep/Oct (2013).

  7. “Carbon fibre and cars-2013 in review”, Reinforced plastics, pp. 18–19, Jan/Feb (2014).

  8. Roch, A. Menrath, T. Huber, T. Henning, and P. Elsner, “Lightweight Potential of Fiber-Reinforced Foams”, Cellular Polymers, Vol. 32, No. 4, pp 213–228 (2013).

  9. Thomason, J. L., & Vlug, M. A. (1996). Influence of fiber length and concentration on the properties of glass fiber-reinforced polypropylene: Part 1-Tensile and flexural modulus. Composites, 27A, 477–484.

    Article  Google Scholar 

  10. Thomason, J. L. (2007). The influence of fibre length and concentration on the properties of glass fibre reinforced polypropylene: Interface strength and fibre strain in injection moulded long fibre PP at high fibre content. Composites Part A: Applied Science Manufacturing., 38(1), 210–216.

    Article  Google Scholar 

  11. Jaafar, J., Siregar, J. P., Salleh, S. M., Hamdan, M. H. M., Cionita, T., & Rihayat, T. (2019). Important Considerations in Manufacturing of Natural Fiber Composites: A Review. International Journal of Precision Engineering and Manufacturing-Green Technology, 6, 647–664.

    Article  Google Scholar 

  12. Fu, S.-Y., & Lauke, B. (1996). Effects of Fiber Length and Fiber Orientation Distributions on the Tensile Strength of Short- Reinforced Polymers. Composite Science and Technology, 56, 1179–1190.

    Article  Google Scholar 

  13. Wang, C., & Yang, S. (2013). Thermal, Tensile and Dynamic Mechanical Properties of Short Carbon Fibre Reinforced Polypropylene Composites. Polymer & Polymer Composites, 21(2), 65–71.

    Article  Google Scholar 

  14. Lafranche, E., Krawczak, P., Ciolczyk, J. P., & Maugey, J. (2007). Injection moulding of long glass fibre reinforced poly-amide 6-6: guidelines to improve flexural properties. Express Polymer Letters, 1, 456–466.

    Article  Google Scholar 

  15. Cilleruelo, L., Lafranche, E., Krawczak, P., Pardo, P., & Lucas, P. (2012). Injection moulding of long glass fibre reinforced poly(ethylene terephtalate): Influence of carbon black and nucleating agents on impact properties. Express Polymer Letters, 6(9), 706–718.

    Article  Google Scholar 

  16. Kim, J.-W., & Lee, D.-G. (2014). Study on the fiber orientation during compression molding of reinforced thermoplastic composites. International Journal of Precision Engineering and Manufacturing-Green Technology, 1, 335–339.

    Article  Google Scholar 

  17. Folgar, F., & Tucker, C. L. (1984). Orientation Behavior of Fibers in Concentrated Suspensions. Journal of Reinforced Plastics and Composites, 3(2), 98–119.

    Article  Google Scholar 

  18. Advani, S. G., & Tucker, C. L. (1987). The Use of Tensors to Describe and Predict Fiber Orientation in Short Fiber Composites. Journal of Rheology, 31(8), 751–784.

    Article  Google Scholar 

  19. Advani, S. G. (1994). Flow and Rheology in Polymer Composites Manufacturing. New York: Elsevier.

    Google Scholar 

  20. Tseng, H.-C., Chang, R.-Y., & Hsu, C.-H. (2013). Phenomenological improvements to predictive models of fiber orientation in concentrated suspensions. Journal of Rheology, 57, 1597.

    Article  Google Scholar 

  21. H.-C. Tseng, R.-Y. Chng, and C.-H. Hsu, “Method and computer readable media for determining orientation of fibers in a fluid”, U.S. Patent No. 8571828 (2013).

  22. H.-C. Tseng, T.-C. Wang, Y.-J. Chang, C.-H. Hsu and R.-Y. Chang, “Progress on Fiber Concentration for Injection Molding Simulation of Fiber Reinforced Thermoplastics”, SPE ANTEC Tech. Papers, 60, (2014).

  23. Foss, P. H., Tseng, H.-C., Snawerdt, J., Chang, Y.-J., Yang, W.-H., & Hsu, C.-H. (2014). Prediction of Fiber Orientation Distribution in Injection Molded Parts Using Moldex3D Simulation. Polymer Composites, 35(4), 671–680.

    Article  Google Scholar 

  24. J. Vlcek, L. Miller, C.-T. Huang (2009) Simulation of screws for injection molding. SPE Annual Tech Papers, pp 2478-2481 (2009).

  25. Potente, H., Effen, N., & Ujma, A. (1996). Injection molding machines. Optimal use by computer simulation. Kunststoffberater, 41(10), 12–17.

    Google Scholar 

  26. C.-T. Huang, H.-C. Tseng, J. Vlcek, and R.-Y. Chang, “Fiber breakage phenomena in long fiber reinforced plastic preparation”, IOP Conf. Series: Materials Science and Engineering, 87, No. 012023, pp. 1–6 (2015).

  27. C.-T. Huang, H.-C. Tseng, R.-Y. Chang, S.-J. Hwang, SPE Annual Tech. Papers, pp. 1120–1125 (2016).

  28. Huang, C.-T., & Tseng, H.-C. (2018). Simulation Prediction of the Fiber Breakage History in Regular and Barrier Structure Screws in Injection Molding. Polymer and Engineering Science, 58(4), 452–459.

    Article  Google Scholar 

  29. Stock, S. R. (2009). Micro-Computed tomography methodology and applications. Boca Raton: CRC Press.

    Google Scholar 

  30. Bernasconi, F. C., & Hine, P. J. (2012). Analysis of fibre orientation distribution in short fibre reinforced polymers: A comparison between optical and tomographic methods”. Composite Science and Technology, 72(16), 2002–2008.

    Article  Google Scholar 

  31. Gandhi, U., Sebastian, D. B., Kunc, V., & Song, Y. (2016). Method to measure orientation of discontinuous fiber embedded in the polymer matrix from computerized tomography scan data. Journal of Thermoplastic Materials., 29(12), 1696–1709.

    Article  Google Scholar 

  32. S. Goris, U. Gandhi, Y.- Y. Song, and T. A. Osswald, Analysis of the process-induced microstructure in injection molding of long glass fiber-reinforced thermoplastics. SPE Annual Tech. Papers, ANTEC2016, pp. 348–356 (2016).

  33. Grellmann, W., & Seidler, S. (2013). Polymer Testing (2nd ed.). Munich: Carl Hanser Verlag.

    Book  Google Scholar 

Download references

Acknowledgements

The authors would like to thank Ministry of Science and Technology of Taiwan, R.O.C. (Project Number: MOST 107-2622-E-006-024-CC1, MOST 108-2221-E-032-013-MY2) for partly financially supporting for this research. The authors also would like to thank Shimadzu Co. (Japan) and Minnotec Co. (Taiwan) for supporting micro-CT measurement and providing a series of images.

Author information

Authors and Affiliations

  1. Department of Chemical and Materials Engineering, Tamkang University, No. 151, Yingzhuan Rd, Tamsui Dist, New Taipei City, 25137, Taiwan

    Chao-Tsai Huang, Jia-Hao Chu, Wei-Wen Fu & Chia Hsu

  2. Department of Mechanical Engineering, National Cheng Kung University, Tainan City, Taiwan

    Sheng-Jye Hwang

Authors
  1. Chao-Tsai Huang
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Jia-Hao Chu
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Wei-Wen Fu
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Chia Hsu
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Sheng-Jye Hwang
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Chao-Tsai Huang.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Huang, CT., Chu, JH., Fu, WW. et al. Flow-induced Orientations of Fibers and Their Influences on Warpage and Mechanical Property in Injection Fiber Reinforced Plastic (FRP) Parts. Int. J. of Precis. Eng. and Manuf.-Green Tech. 8, 917–934 (2021). https://doi.org/10.1007/s40684-020-00226-2

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s40684-020-00226-2

Keywords

Search

Navigation