Abstract
Sit-to-stand (STS) motion is one of the most important tasks in daily life and is one of the key determinants of functional independence, especially for the senior people. The STS motion has been extensively studied in the literature, mostly through experiments. Compared to numerous experimental studies, there are limited simulations with mostly assuming bilateral symmetry for STS tasks. However, it is not true even for healthy individuals to perform STS tasks with a perfect bilateral symmetry. In this study, predictive dynamics is utilized for STS prediction. The problem can be constructed as a nonlinear optimization formulation. The digital human model has 21 degrees of freedom (DOFs) for the unassisted STS tasks. The quartic B-spline interpolation is implemented for representing joint angle profiles. The recursive Lagrangian dynamics approach and the Denavit–Hartenberg method are implemented for the equations of motion. This study is to develop a generic three-dimensional unassisted STS motion prediction method for healthy young and elderly individuals. Results show that trunk joint angle peak values are similar between the two virtual-groups in the sagittal, frontal, and transverse planes. Lower-limbs’ joint angle and velocity profiles and their peak values between the right and left side for both virtual groups are also similar. The normalized peak joint torques are slight differences in each active DOF between the two virtual groups and the peak values are similar. The proposed method has been indirectly validated through the literature experimental results. The developed method has various potential applications in the design of exoskeleton, microelectromechanical system for fall detection, and assistive devices in rehabilitation.
Similar content being viewed by others
References
Dall, P.M., Kerr, A.: Frequency of the sit to stand task: an observational study of free-living adults. Appl. Ergon. 41(1), 58–61 (2010)
Schultz, A.B., Alexander, N.B., Ashton-Miller, J.A.: Biomechanical analyses of rising from a chair. J. Biomech. 25(12), 1383–1391 (1992)
Dawson, D.A., Hendershot, G.E., Fulton, J.P.: Aging in the eighties: functional limitations of individuals age 65 years and over. National Center for Health Statistics (U.S.) (1987)
Riley, P., Schenkman, M.L., Mann, R.W., Andrew, W.: Mechanics of a constrained chair-rise. J. Biomech. 24(1), 77–85 (1991)
Gross, M.M., Stevenson, P.J., Charette, S.L., Pyka, G., Marcus, R.: Effect of muscle strength and movement speed on the biomechanics of rising from a chair in healthy elderly and young women. Gait Posture 8(3), 175–185 (1998)
Kralj, A., Jaeger, R.J., Munih, M.: Analysis of standing up and sitting down in humans: definitions and normative data presentation. J. Biomech. 23(11), 1123–1138 (1990)
Pai, Y.-C., Naughton, B.J., Chang, R.W., Rogers, M.W.: Control of body centre of mass momentum during sit-to-stand among young and elderly adults. Gait Posture 2(2), 109–116 (1994)
Hughes, M.A., Weiner, D.K., Schenkman, M.L., Long, R.M., Studenski, S.A.: Chair rise strategies in the elderly. Clin. Biomech. 9(3), 187–192 (1994)
Pai, Y.-C., Rogers, M.W.: Speed variation and resultant joint torques during sit-to-stand. Arch. Phys. Med. Rehabil. 72(11), 881–885 (1991)
Lord, S.R., Murray, S.M., Chapman, K., Munro, B., Tiedemann, A.: Sit-to-stand performance depends on sensation, speed, balance, and psychological status in addition to strength in older people. J. Gerontol., Ser. A, Biol. Sci. Med. Sci. 57(8), 539–543 (2002)
Papa, E., Cappozzo, A.: Sit-to-stand motor strategies investigated in able-bodied young and elderly subjects. J. Biomech. 33, 1113–1122 (2000)
Papa, E., Cappozzo, A.: A telescopic inverted-pendulum model of the musculo-skeletal system and its use for the analysis of the sit-to-stand motor task. J. Biomech. 32(11), 1205–1212 (1999)
Dehail, P., Bestaven, E., Muller, F., Mallet, A., Robert, B., Bourdel-Marchasson, I., Petit, J.: Kinematic and electromyographic analysis of rising from a chair during a ‘sit-to-walk’ task in elderly subjects: role of strength. Clin. Biomech. 22(10), 1096–1103 (2007)
Yoshioka, S., Nagano, A., Hay, D.C., Fukashiro, S.: Biomechanical analysis of the relation between movement time and joint moment development during a sit-to-stand task. Biomed. Eng. Online 8(2), 27 (2009)
Fujimoto, M., Chou, L.-S.: Dynamic balance control during sit-to-stand movement: an examination with the center of mass acceleration. J. Biomech. 45(3), 543–548 (2012)
Mourey, F., Grishin, A., D’Athis, P., Pozzo, T., Stapley, P.: Standing up from a chair as a dynamic equilibrium task: a comparison between young and elderly subjects. J. Gerontol., Ser. A, Biol. Sci. Med. Sci. 55(9), B425–B431 (2000)
Lundin, T.M., Grabiner, M.D., Jahnigen, D.W.: On the assumption of bilateral lower extremity joint moment symmetry during the sit-to-stand task. J. Biomech. 28(1), 109–112 (1995)
Gillette, J.C., Stevermer, C.A.: The effects of symmetric and asymmetric foot placements on sit-to-stand joint moments. Gait Posture 35(1), 78–82 (2012)
Gilleard, W., Crosbie, J., Smith, R.: Rising to stand from a chair: symmetry, and frontal and transverse plane kinematics and kinetics. Gait Posture 27(1), 8–15 (2008)
Roy, G., Nadeau, S., Gravel, D., Malouin, F., McFadyen, B.J., Piotte, F.: The effect of foot position and chair height on the asymmetry of vertical forces during sit-to-stand and stand-to-sit tasks in individuals with hemiparesis. Clin. Biomech. 21(6), 585–593 (2006)
Kawagoe, S., Tajima, N., Chosa, E.: Biomechanical analysis of effects of foot placement with varying chair. J. Orthop. Sci. 5(2), 124–133 (2000)
Rodosky, M.W., Andriacchi, T.P., Andersson, G.B.: The influence of chair height on lower limb mechanics during rising. J. Orthop. Res. 7(2), 266–271 (1989)
Burdett, R.G., Habasevich, R., Pisciotta, J., Simon, S.R.: Biomechanical comparison of rising from two types of chairs. Phys. Ther. 65(8), 1177–1183 (1985)
Arborelius, U.P., Wretenberg, P., Lindberg, F.: The effects of armrests and high seat heights on lower-limb joint load and muscular activity during sitting and rising. Ergonomics 35(11), 1377–1391 (1992)
Anglin, C., Wyss, U.P.: Arm motion and load analysis of sit-to-stand, stand-to-sit, cane walking and lifting. Clin. Biomech. 15(6), 441–448 (2000)
O’Meara, D.M., Smith, R.M.: The effects of unilateral grab rail assistance on the sit-to-stand performance of older aged adults. Hum. Mov. Sci. 25(2), 257–274 (2006)
Kamnik, R., Bajd, T., Kralj, A.: Functional electrical stimulation and arm supported sit-to-stand transfer after paraplegia: a study of kinetic parameters. Artif. Organs 23(5), 413–417 (1999)
Najafi, B., Aminian, K., Loew, F., Blanc, Y., Robert, P.A.: Measurement of stand-sit and sit-stand transitions using a miniature gyroscope and its application in fall risk evaluation in the elderly. IEEE Trans. Biomed. Eng. 49(8), 843–851 (2002)
Ikeda, E.R., Schenkman, M.L., Riley, P.O., Hodge, W.A.: Influence of age on dynamics of rising from a chair. Phys. Ther. 71(6), 473–481 (1991)
Shepherd, R.B., Koh, H.P.: Some biomechanical consequences of varying foot placement in sit-to-stand in young women. Scand. J. Rehabil. Med. 28(2), 79–88 (1996)
Su, F.C., Lai, K.A., Hong, W.H.: Rising from chair after total knee arthroplasty. Clin. Biomech. 13(3), 176–181 (1998)
Talis, V.L., Grishin, A.A., Solopova, I.A., Oskanyan, T.L., Belenky, V.E., Ivanenko, Y.P.: Asymmetric leg loading during sit-to-stand, walking and quiet standing in patients after unilateral total hip replacement surgery. Clin. Biomech. 23(4), 424–433 (2008)
Coghlin, S.S., McFadyen, B.J.: Transfer strategies used to rise from a chair in normal and low back pain subjects. Clin. Biomech. 9(2), 85–92 (1994)
Mizner, R.L., Snyder-Mackler, L.: Altered loading during walking and sit-to-stand is affected by quadriceps weakness after total knee arthroplasty. J. Orthop. Res. 23, 1083–1090 (2005)
Mak, M.K.Y., Levin, O., Mizrahi, J., Christina, H.-C.W.Y.: Joint torques during sit-to-stand in healthy subjects and people with Parkinson’s disease. Clin. Biomech. 18(3), 197–206 (2003)
Bahrami, F., Riener, R., Jabedar-Maralani, P., Schmidt, G.: Biomechanical analysis of sit-to-stand transfer in healthy and paraplegic subjects. Clin. Biomech. 15(2), 123–133 (2000)
Sibella, F., Galli, M., Romei, M., Montesano, A., Crivellini, M.: Biomechanical analysis of sit-to-stand movement in normal and obese subjects. Clin. Biomech. 18(8), 745–750 (2003)
Lou, S.-Z., Chou, Y.-L., Chou, P.-H., Lin, C.-J., Chen, U.-C.: Sit-to-stand at different periods of pregnancy. Clin. Biomech. 16(3), 194–198 (2001)
Gilleard, W., Crosbie, J., Smith, R.: A longitudinal study of the effect of pregnancy on rising to stand from a chair. J. Biomech. 41(4), 779–787 (2008)
Pandy, M.G., Garner, B.A., Anderson, F.C.: Optimal control of non-ballistic muscular movements: a constraint-based performance criterion for rising from a chair. ASME J. Biomech. Eng. 117(1), 15–26 (1995)
Domire, Z.J.: A biomechanical analysis of maximum vertical jumps and sit-to-stand. PhD dissertation, Pennsylvania State University (2004)
Kuzelicki, J., Zefran, M., Burger, H., Bajd, T.: Synthesis of standing-up trajectories using dynamic optimization. Gait Posture 21(1), 1–11 (2005)
Mughal, A., Iqbal, K.: 3D bipedal model with holonomic constraints for the decoupled optimal controller design of the biomechanical sit-to-stand maneuver. ASME J. Biomech. Eng. 132(4), 041010 (2010)
Robert, T., Causse, J., Monnier, G.: Estimation of external contact loads using an inverse dynamics and optimization approach: General method and application to sit-to-stand maneuvers. J. Biomech. 46(13), 2220–2227 (2013)
Ozsoy, B., Yang, J.: Simulation-based unassisted sit-to-stand motion prediction for healthy young individuals. In: Proceedings of the ASME 2014 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference IDETC/CIE, Buffalo, NY, USA (2014)
Abdel-Malek, K., Arora, J.: Human Motion Simulation: Predictive Dynamics, 1st edn. Academic Press, New York (2013)
Xiang, Y., Chung, H.-J., Kim, J.H., Bhatt, R., Rahmatalla, S., Yang, J., Marler, T., Arora, J.S., Abdel-Malek, K.: Predictive dynamics: an optimization-based novel approach for human motion simulation. Struct. Multidiscip. Optim. 41(3), 465–479 (2009)
Denavit, J., Hartenberg, R.S.: A kinematic notation for lower-pair mechanisms based on matrices. J. Appl. Mech. 22, 215–221 (1955)
Gordon, C.C., Churchill, T., Clauser, C.E., Bradtmiller, B., McConville, J.T., Tebbetts, I., Walker, R.A.: Anthropometric survey of U.S. army personnel: methods and summary statistics. Final report NATICK/TR-89/027, U.S. Army Natick Research, Development and Engineering Center, Natick, MA (1988)
McConville, J., Clauser, C., Churchill, T.: Anthropometric relationships of body and body segment moments of inertia. Anthropology Research Project inc., Yellow Springs, OH (1980)
Piegl, L., Tiller, W.: The NURBS Book. Springer, New York (1997)
Xiang, Y., Arora, J.S., Abdel-Malek, K.: Optimization-based motion prediction of mechanical systems: sensitivity analysis. Struct. Multidiscip. Optim. 37(6), 595–608 (2008)
Howard, B., Yang, J.: A New stability criterion for human seated tasks with given postures. Int. J. Humanoid Robot. 09(03), 1250015 (2012)
Kerr, K.M., White, J.A., Barr, D.A., Mollan, R.A.B.: Analysis of sit-to-stand movement cycle in normal subjects. Clin. Biomech. 12, 236–245 (1997)
Anderson, D.E., Madigan, M.L., Nussbaum, M.A.: Maximum voluntary joint torque as a function of joint angle and angular velocity: model development and application to the lower limb. J. Biomech. 40(14), 3105–3113 (2007)
Cahalan, T.D., Johnson, M.E., Liu, S.C.E.: Quantitative measurements of hip strength in different age groups. Clin. Orthop. Relat. Res. 246, 136–145 (1989)
Kumar, S.: Isolated planar trunk strengths measurement in normals, part III: results and database. Int. J. Ind. Ergon. 17, 103–111 (1996)
Roebuck, J.A., Kroemer, K.H.E., Thomson, W.G.: Engineering Anthropometry Methods. Wiley–Interscience, New York (1975)
Shephard, R.J.: A personal perspective on aging and productivity, with particular reference to physically demanding work. Ergonomics 38(4), 617–636 (1995)
Hirschfeld, H., Thorsteinsdottir, M., Olsson, E.: Coordinated ground forces exerted by buttocks and feet are adequately programmed for weight transfer during sit-to-stand. J. Neurophysiol. 82(6), 3021–3029 (1999)
Roebroeck, M.E., Doorenbosch, C.A.M., Harlaar, J., Jacobs, R., Lankhorst, G.J.: Biomechanics and muscular activity during sit-to-stand transfer. Clin. Biomech. 9(4), 235–244 (1994)
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Yang, J., Ozsoy, B. Three dimensional unassisted sit-to-stand prediction for virtual healthy young and elderly individuals. Multibody Syst Dyn 49, 33–52 (2020). https://doi.org/10.1007/s11044-019-09699-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11044-019-09699-9