Next Article in Journal
White Matter and Neuroprotection in Alzheimer’s Dementia
Next Article in Special Issue
Magnetic Solid-Phase Extraction of Organic Compounds Based on Graphene Oxide Nanocomposites
Previous Article in Journal
Impacts of Chemical-Assisted Thermal Pretreatments on Methane Production from Fruit and Vegetable Harvesting Wastes: Process Optimization
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

A New Method for Determination of Thymol and Carvacrol in Thymi herba by Ultraperformance Convergence Chromatography (UPC2)

1
Institute of Chinese Materia Medica, China Academy of Chinese Medical Sciences, Beijing 100700, China
2
Artemisinin Research Center, China Academy of Chinese Medical Sciences, Beijing 100700, China
*
Authors to whom correspondence should be addressed.
These authors contributed equally to this work.
Molecules 2020, 25(3), 502; https://doi.org/10.3390/molecules25030502
Submission received: 19 December 2019 / Revised: 15 January 2020 / Accepted: 21 January 2020 / Published: 23 January 2020
(This article belongs to the Special Issue Advances towards Green Analytical Chemistry)

Abstract

:
Ultraperformance convergence chromatography is an environmentally friendly analytical technique for dramatically reducing the use of organic solvents compared to conventional chromatographic methods. In this study, a rapid and sensitive ultraperformance convergence chromatography method was firstly established for quantification of thymol and carvacrol, two positional isomers of a major bioactive in the volatile oil of Thymi herba, the dried leaves and flowers of Thymus mongolicus or Thymus przewalskii, known in China as “Dijiao.” Using a TrefoilTM CEL1 column, thymol and carvacrol were separated in less than 2.5 min and resolution was enhanced. The method was validated with respect to precision, accuracy, and linearity according to the National Medical Products Administration guidelines. The optimized method exhibited good linear correlation (r = 0.9998−0.9999), excellent precision (relative standard deviations (RSDs) < 1.50%), and acceptable recoveries (87.29–102.89%). The limits of detection for thymol and carvacrol were 1.31 and 1.57 ng/L, respectively, while their corresponding limits of quantification were 2.63 and 3.14 ng/L. Finally, the quantities of the two compounds present in 16 T. mongolicus and four T. przewalskii samples were successfully evaluated by employing the developed method. It is hoped that the results of this study will serve as a guideline for the quality control of Thymi herba.

1. Introduction

Thymi herba is the dried leaves and flowers of Thymus mongolicus (T. mongolicus) or Thymus przewalskii (T. przewalskii), known as “Dijiao (地椒)” in China, which has been included in the Chinese Pharmacopoeia (1977) for the treatment of coughs, headaches, abdominal pains, and diarrhea [1]. It is also used as a folk seasoning in some areas of the country [2]. Though Thymi herba has been effective and widely used for years, appropriate quality control (QC) criteria, which aim to ensure their consistency, safety, and efficacy, are still lacking. Hence, it is imperative to conduct a suitable QC assessment of Thymi herba for the benefit of consumers.
Typically, the QC of herbal medicines is carried out by measuring the chemical markers present in the medicines. Ideally, chemical markers should be unique components that contribute to the therapeutic effects of a herbal medicine [3,4]. Pharmacological studies show that Thymus essential oil is the main active component of Thymi herba, which has anti-inflammatory [5,6,7], antioxidant [8], antitumor [9], and antithrombotic [10,11] activities.
Thymol (2-isopropyl-5-methylphenol) and carvacrol (5-isopropyl-2-methylphenol) are two main components of Thymus essential oil [12,13,14,15,16,17,18]. Thus, for Thymi herba, thymol (Thl) and carvacrol (Cal) are considered to be two of the most effective active components (Figure 1). In addition, Thl and Cal have been used in the assay criteria for Thymus vulgaris L. and Thymus zygis L. in the European Pharmacopoeia and the British Pharmacopoeia [19]. According to these previous reports, Thl and Cal might be suitable chemical markers for the QC of Thymi herba.
Because Thl and Cal are positional isomers, it is usually difficult to completely separate them. So far, only a few methods have been developed for the analysis and quantification of Thl and Cal, such as gas chromatography (GC) and high-performance liquid chromatography (HPLC). The gas chromatography (GC) method (capillary column, column temperature programmed (40 to 220 °C), detector temperature of 230 °C, analysis time 45 min) has been established for the determination of Thl and Cal in Thymus vulgaris L. and Thymus zygis L. essential oil in the European Pharmacopoeia (European Pharmacopoeia, 2014, 9, 1538–1560). Apart from this, Pei X. et al. also developed a GC system (capillary column, column temperature programmed (50 to 210 °C), detector temperature of 230 °C, analysis time 25 min) to determine the content of Thl and Cal in T. mongolicus (content determination of thymol and carvacrol from Herba Thyma by GC. Chin. J. Exp. Tradit. Med. Form. 2013, 19, 132–134). Additionally, Ji L. et al. used a high-performance liquid chromatography (HPLC) method (Inertsil ODS-3 column, methanol–water–acetic acid (60:40:2) as mobile phase, analysis time 35 min) to determine the content of Thl and Cal in Mosla chinensis (determination of carvacrol and thymol in Mosla chinensis by HPLC. Chin. J. Chin. Mater. Med. 2004, 29, 8–10). Each method has its unique virtues and drawbacks. GC possesses high selectivity and fine sensitivity [4], but requires extraction of volatile oil [19], operates at high temperatures (40–220 °C), and can require up to 15 min to separate the components [20]. HPLC does not require the extraction of volatile oil, but requires large quantities of organic solvents or chemicals to be consumed, has difficulty in completely separating Thl and Cal, and can require up to 28–31 min to separate the components [21]. Therefore, it is imperative to develop a rapid, reliable, and environmentally friendly method for the QC of Thymi herba to ensure its appropriate use for therapeutic purposes.
Ultraperformance convergence chromatography (UPC2) has been commercialized by Waters since 2012 [22]. As one of the latest kinds of chromatography technologies, it integrates supercritical fluid chromatography (SFC) and ultraperformance liquid chromatography (UPLC) technologies, which results in many remarkable advantages, including reduced run time, lower solvent consumption, reliability, high resolution, and sensitivity, all of which make its application to routine analysis very attractive. More importantly, UPC2 is an environmentally friendly analytical technique that employs dramatically reduced quantities of organic solvents compared to conventional chromatographic methods [23,24]. Nowadays, UPC2 technology has been widely utilized in pharmaceutical analysis, and could serve as an alternative or complementary approach alongside HPLC and GC [25,26,27]. To the best of our knowledge, no studies have been reported on the use of UPC2 for analyzing Thl and Cal in Thymi herba as QC markers.
In this study, a rapid, reliable, and environmentally friendly UPC2 method for the simultaneous separation and determination of Thl and Cal in Thymi herba was developed and validated for the first time. Using this method, the Thl and Cal contents of 16 samples of T. mongolicus and four samples of T. przewalskii were analyzed. It is hoped that this study will serve as a guideline for the QC of Thymi herba.

2. Materials and Methods

2.1. Chemicals and Reagents

Reference compounds of Thl and Cal were purchased from the National Institutes for Food and Drug Control (Beijing, China). HPLC-grade methanol and ethanol solvents were obtained from Fisher Scientific Co. (Pittsburgh, PA, USA), CO2 (99.999% purity) came from Xenon Heyu Gas Technology Co., Ltd. (Beijing, China), and ultrapure water (18.2 MΩ resistivity) was prepared with a Millipore ultragenetic polishing system (Millipore, Bedford, MA, USA). All solvents were filtered through 0.22 μm filters before use.
Thymi herba samples were collected when the flowers were in full bloom in summer and autumn (about June to August). A total of 20 Thymi herba samples were purchased/collected from different geographical areas (samples T-1 to T-10 were purchased from different medicinal materials markets on different dates, and samples T-11 to T-20 were collected from different producing areas in June and dried naturally in the shade) (Table 1). All samples were identified as T. mongolicus or T. przewalskii by Prof. Chunsheng Liu of Beijing University of Chinese Medicine. The voucher specimens (No. ZYS2017T01-T20) have been deposited in the Institute of Chinese Materia Medica, China Academy of Chinese Medical Sciences, Beijing. The samples were deposited in a cool, dry place.

2.2. Standard Preparation and Calibration

Stock standard solutions were prepared by dissolving the commercially obtained standards (1.68 mg Thl and 2.01 mg Cal) in methanol (10 mL). Six calibrated standard solutions were prepared using increasing concentrations of the stock solutions and serially diluting them with methanol. A linear correlation between the peak areas of the chromatogram and the concentrations of the components was determined. The linear regression equation obtained was used for quantification of Thl and Cal in selected Thymi herba samples.

2.3. Sample Preparation

A quantity (3000 g) of the powdered herbal drug was weighed into a 125 mL glass vial with a screw cap. Acetone (Sinopharm Chemical Reagent Co., Ltd, Shanghai, China) (60 mL) was added and the solution was extracted for 40 min using ultrasound. The suspension was then centrifuged for 5 min and the supernatant collected. A quantity (40 mL) of the supernatant was transferred to a flask and evaporated to dryness using a rotary evaporator (at 30 °C and 27 mbar). Methanol (5 mL) was then added to the residue, which was dissolved with the aid of ultrasound for approximately 5 min. The supernatant was filtered through membrane glass fiber filters (0.22 μm, Millipore membrane, Bedford, MA, USA) prior to UPC2 (Waters, Milford, MA,USA) analysis.

2.4. Apparatus and Separation Conditions

Compounds of interest were analyzed using a Waters ACQUITY® UPC2TM system (Waters, Milford, MA, USA) equipped with a binary solvent delivery pump, an autosampler, a column oven, a back-pressure regulator, and a diode-array detector. The quantitative analysis was performed using a TrefoilTM CEL1 column (2.1 × 150 mm, 2.5 μm, Waters, Milford, MA, USA). The elution gradient of methanol (B) in CO2 (A) was used as follows—1% B (initial), 1%–3% B (0–1.5 min), 3%–3% B (1.5–2.5 min), 3%–15% B (2.5–10 min). The automated back pressure regulator (ABPR) was set at 1700 psi. The flow rate was kept at 1.0 mL/min, and the column and autosampler temperatures were set at 30 and 15 °C, respectively. The detection wavelength was set at 274 nm, and the injection volume was 1.0 μL. Data processing was performed using Empower 3 software (Waters, Milford, MA, USA).

2.5. Method Validation

The proposed method was validated according to National Medical Products Administration guidelines for the validation of analytical methods for pharmaceutical quality standards, with respect to linearity, limit of detection (LOD) and limit of quantification (LOQ), and for precision and accuracy [28].
Linearity was assessed by plotting the peak area versus concentration of each isomer. The LOD and LOQ were determined as those concentrations where the ratios of the peak heights of interest to the baseline noise were 3 and 10, respectively.
The precision of the analyses for Thl and Cal was determined by three consecutive interday precision measurements and six consecutive intraday precision measurements. The relative standard deviation (RSD) was calculated from the standard deviation (SD) as:
SD/mean × 100
The stability of each sample was tested at room temperature (25 °C) and analyzed at 0, 3, 6, 9, 12, 24, 48, and 72 h. Recovery tests were performed by spiking known amounts of the sample to three concentration levels (high, medium, and low) of the standard solution. Recovery was expressed as:
(starting concentration-added concentration)/spiked concentration × 100

3. Results and Discussion

3.1. Optimization of UPC2 Conditions

In order to separate Thl and Cal from T. mongolicus and T. przewalskii, the chromatographic conditions were optimized to achieve good resolution within a reasonable analysis time. First, different columns purchased from Waters were investigated: Waters ACQUITY® UPC2™ Viridis BEH (3.0 × 100 mm, 1.7 μm, Waters, Dublin, UK), Trefoil CEL1 (2.1 × 150 mm, 2.5 μm, Waters, Milford, MA, USA), Trefoil CEL2 (2.1 × 150 mm, 2.5 μm, Waters, Milford, MA, USA), Trefoil AMY1 (2.1 × 150 mm, 2.5 μm, Waters, Milford, MA, USA), Torus DEA (2.1 × 100 mm, 1.7 μm, Waters, Dublin, UK), Torus Diol (2.1 × 100 mm, 1.7 μm, Waters, Dublin, UK), Torus 2-PIC (2.1 × 100 mm, 1.7 μm, Waters, Dublin, UK), and Torus 1-AA (2.1 × 100 mm, 1.7 μm, Waters, Dublin, UK) columns. As can be observed, the Viridis BEH and Torus 1-AA columns could not separate Thl and Cal at all. The Trefoil CEL2, Torus DEA, Torus Diol, and Torus 2-PIC columns detected Thl and Cal, but Thl and Cal peaks were not well separated. Only the Trefoil CEL1 and Trefoil AMY1 columns detected Thl and Cal peaks that were well separated. Notably, the Trefoil CEL1 column led to shorter analysis time and better resolution and peak shape (Figure S1). Therefore, the Trefoil CEL1 column was selected as the optimum column for further investigation. Next, in order to improve the separation of Thl and Cal, different solvents for mobile phase B, including methanol, acetonitrile, and ethanol, were investigated. When acetonitrile and ethanol were used as mobile phase B, the peaks of Thl and Cal could not be separated completely. However, the best result was obtained using a mixture of CO2 and methanol as mobile phase B with a linear-gradient elution mode. The polarity of methanol is between acetonitrile and ethanol. We speculated that the separation of Thl and Cal may be significantly affected by the polarity of mobile phase B and the polarity of mobile phase B is slightly larger or smaller, which is not conducive to the separation of the two isomers. It is noteworthy that the back pressure directly influences the eluting power of a supercritical fluid by changing the density of supercritical carbon dioxide [26]. Hence, different values of back pressure (1700, 1800, 2000, and 2500 psi) were investigated. With increasing back pressure, the eluting power increased accordingly, resulting in decreased analysis time and resolution. In this work, Thl and Cal were not separated on the back pressure at 1800, 2000, and 2500 psi. Finally, an optimal back pressure of 1700 psi was selected for UPC2 analysis. Different column temperatures (30, 35, and 40 °C) and different flow rates (0.7, 1.0, and 1.2 mL/min) were then investigated. The test results showed that the column temperature and flow rates had no significant effect on the resolution of Thl and Cal. However, considering that the Trefoil CEL1 column itself can withstand temperatures not exceeding 40 °C, a lower temperature should be selected without affecting the separation effect. While a flow rate of greater than or equal to 1.2 mL/min resulted in high column pressure, the flow rate was set to 1.0 mL/min, which afforded a lower column pressure and higher resolution. Hence, the optimal column temperature and flow rate were chosen as 30 °C and 1.0 mL/min, respectively. It is important to note that the injection volume directly influences component resolution and peak shape. Therefore, different values of the injection volume (0.5, 1.0, and 2.0 μL) were investigated. With increasing injection volume, the peak shape widened accordingly, resulting in decreased resolution. The optimal injection volume was chosen as 1.0 μL.
Finally, the mobile phase gradient elution program was carefully designed. The smaller the proportion of mobile phase B to supercritical CO2, the later that Thl and Cal were eluted. When the elution gradient of methanol (B) in CO2 (A) was used as follows—1% B (initial), 1%–3% B (0–1.5 min), and 3%–3% B (1.5–2.5 min)—both Thl and Cal were well separated and the resolutions were good (retention expressed by capacity factor: k1′ = 3.67, k2 = 4.11; selectivity: α = 1.12; resolution: Rs = 2.00). The formula to calculate the capacity factor: k’; selectivity: α; and resolution: Rs were expressed as:
k1 = (tR1tM)/tM
k2 = (tR2tM)/tM
α = (tR2tM)/(tR1tM)
Rs = (tR2tR1)/[1/2 × (W1 + W2)]
(tM, dead time; tR1, retention time of thymol (Thl); tR2, retention time of carvacrol (Cal); W1, peak width of thymol (Thl); W2, peak width of carvacrol (Cal)).

3.2. Method Validation

3.2.1. Linearity and Sensitivity

Standard stock solutions of Thl and Cal in methanol were prepared. Serial dilution was performed to construct standard calibration curves, with Thl concentrations of 168.00, 84.00, 42.00, 21.00, 10.50, and 5.25 ng/L and Cal concentrations of 201.00, 100.50, 50.25, 25.13, 12.56, and 6.28 ng/L. Good linearity for the two isomers was observed (Table 2), which ensured acquisition of reliable data for different types of samples with both low and high Thl and Cal contents in T. monoglicus and T. przewalskii.
The LOD was determined as the concentration where the ratio between the peak height of interest and baseline noise was three, and the values ranged from 1.31 to 1.57 ng. The LOQ was determined as the concentration where the ratio between the peak height of interest and baseline noise was 10, and this ranged from 2.63 to 3.14 ng. The result suggested that the UPC2 method allows detection of small quantities of Thl and Cal in T. monoglicus or T. przewalskii.

3.2.2. Precision and Accuracy

The precision of the analyses for Thl and Cal was determined from three consecutive interday precision measurements and six consecutive intraday precision measurements. Interday precision was determined from the standard solutions of the two isomers over three consecutive days. Intraday precision was determined from the standard solutions of the two isomers over six consecutive measurements during a single day. The RSDs of interday precision and intraday precision were 0.71% and 1.16% for Thl and 1.50% and 0.39% for Cal, respectively, indicative of good precision (Table 3). The Thl and Cal were proved to be stable in the sample solution over 72 h at room temperature, with the RSDs below 1.86% and 1.90%, respectively.
The accuracy of the method was determined by spiking known amounts of T. mongolicus to three concentrations—low, medium, and high—of the standard solution. All procedures were performed in triplicate, and the sample injections were done in duplicate. The recovery rates for the investigated components ranged from 87.35% to 102.89%, and the RSD values were less than 2.40%, demonstrating that the method we have developed is reproducible, with good accuracy (Table 4).

3.3. Quantitative Analysis of T. mongolicus and T. przewalskii

The UPC2 method developed in this study was applied for the quantitative determination of the two isomers, Thl and Cal, in 16 samples of T. mongolicus and four samples of T. przewalskii. Figure 2A shows the typical chromatographic profile of standard solutions of Thl and Cal, and the retention times of Thl and Cal were found to be 2.108 min and 2.248 min, respectively. Figure 2B,C presents, respectively, the representative UPC2 chromatograms of T. mongolicus and T. przewalskii, and Table 5 summarizes the results obtained. Thl and Cal from the aerial parts of T. mongolicus were detected in the ranges 0.066–0.224‰ and 0.090–0.616‰, respectively, and Thl and Cal from the aerial parts of T. przewalskii were detected in the ranges 0.086–0.246‰ and 0.205–0.323‰, respectively.
This result is in good agreement with the GC quantitative results obtained (Table 6) for these two isomers in T. mongolicus in the study reported by Pei X. et al. [20]. It shows that the UPC2 method is accurate and reliable, and it may substitute conventional methods used to determine Thl and Cal.
Green analytical chemistry (GAC), which focuses on the development of novel analytical methodologies to reduce the environmental impact of traditional analytical methods, is becoming a more important issue for the public and researchers in recent years [29,30]. Tedious time and organic solvents are always needed to separate the two isomers (Thl and Cal) through the existing GC and HPLC methods, owing to their similar characters. In this work, we have established a UPC2 method, and the two isomers are separated efficiently in 2.3 min (6.5-fold shorter (2.3 vs. 15 min) than the GC method and 13.0-fold shorter (2.3 vs. 30 min) than the HPLC method). Meanwhile, a cheap, sustainable, and environmentally benign mobile phase consisting of 1%–3% methanol in CO2 is employed in our procedure. The organic solvent consumption and total costs are significantly reduced compared with the previous HPLC method.
Additionally, samples of the same species collected from the different producing region also exhibited considerable differences in Thl and Cal contents. For example, T-1, T-4, and T-9 samples of the same species T. przewalskii contained different amounts of Thl and Cal. These results possibly reflect the differences in the quality and bioactivity of T. przewalskii.
Hence, we propose that our optimized UPC2 method would be particularly convenient for the rapid, accurate, environmentally friendly, and sensitive monitoring the contents of Thl and Cal in Thymi herba samples.

4. Concluding Remarks

In this study, a UPC2 method was established for the first time for the simultaneous determination of the two isomers thymol (Thl) and carvacrol (Cal) in Thymi herba (Dijiao, 地椒), which have pharmacological activities. The established method was validated by the linearity, reproducibility, recovery, accuracy, and precision of the results—all parameters were found to be satisfactory. This newly established UPC2 method will be helpful in the quality assessment of Thymi herba and related herbal formulas in future.

Supplementary Materials

The following are available online at https://www.mdpi.com/1420-3049/25/3/502/s1, Figure S1: UPC2 chromatograms for the separation of 2 isomers by different columns. 1 and 2 represent thymol (Thl) and carvacrol (Cal), respectively.

Author Contributions

D.Z. and L.Y. planned, designed, and organized the whole research of this study. X.C. and D.H. established the ultraperformance convergence chromatography method and analyzed the Thymi herba samples. P.S. and Y.M. revised the manuscript. Y.Z. and Y.B. collected the plant material and carried out the extraction. All authors have read and agreed to the published version of the manuscript.

Funding

This work was financially supported by the Key project at central government level: The ability establishment of sustainable use for valuable Chinese medicine resources (2060302).

Acknowledgments

The authors would also like to thank Chunsheng Liu for the identification of 16 samples of T. mongolicus and four samples of T. przewalskii.

Conflicts of Interest

We declare that there is no conflict of interest with this work.

References

  1. Chinese Pharmacopoeia Commission. Chinese Pharmacopoeia; People’s Health Publishing House: Beijing, China, 1977; Volume 1. [Google Scholar]
  2. Quan, J.; Lv, G.; He, S.; Peng, F.; Nie, C.; Xia, B. Investigation and analysis of Thymus wild resources in China. North Horticult. 2012, 2, 87–91. [Google Scholar]
  3. Li, S.; Han, Q.; Qiao, C.; Song, J.; Cheng, C.L.; Xu, H. Chemical markers for the quality control of herbal medicines: An overview. Chin. Med. 2008. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  4. Guo, W.; Bian, Z.; Zhang, D.; Tang, G.; Liu, W.; Wang, J.; Li, Z.; Yang, F. Simultaneous determination of herbicides residues in tobacco using ultra performance convergence chromatography coupled with solid-phase extraction. J. Sep. Sci. 2015, 38, 858–863. [Google Scholar] [CrossRef]
  5. Cosentino, S.; Tuberoso, C.I.G.; Pisano, B.; Satta, M.; Mascia, V.; Arzedi, E.; Palmas, F. In-vitro antimicrobial activity and chemical composition of Sardinian Thymus essential oils. Lett. Appl. Microbiol. 1999, 29, 130–135. [Google Scholar] [CrossRef] [PubMed]
  6. Yamazaki, K.; Yamamoto, T.; Kawai, Y.; Inoue, N. Enhancement of antilisterial activity of essential oil constituents by nisin and diglycerol fatty acid ester. Food Microbiol. 2004, 21, 283–289. [Google Scholar] [CrossRef]
  7. Pina-Vaz, C.; Rodrigues, A.G.; Pinto, E.; Costa-De-Oliveira, S.; Tavares, C.; Salgueiro, L.; Cavaleiro, C.; Gonçalves, M.; Martinez-De-Oliveira, J. Antifungal activity of Thymus oils and their major compounds. J. Eur. Acad. Dermatol. Venereol. 2004, 18, 73–78. [Google Scholar] [CrossRef]
  8. Hotta, M.; Nakata, R.; Katsukawa, M.; Hori, K.; Takahashi, S.; Inoue, H. Carvacrol, a component of thyme oil, activates PPARα and γ and suppresses COX-2 expression. J. Lipid Res. 2010, 51, 132–139. [Google Scholar] [CrossRef] [Green Version]
  9. Wu, S.; Wei, F.X.; Li, H.Z.; Liu, X.G.; Zhang, J.H.; Liu, J.X. Chemical composition of essential oil from Thymus citriodorus and its toxic effect on liver cancer cells. J. Chin. Med. Mater. 2013, 36, 756–759. [Google Scholar]
  10. Zheng, Q.; Liu, P.; Shi, Y.; Nie, H. The effects of volatile oil of Thymus mongolicus Ronn. on microcirculation and its antithrombotic action in vitro. J. Taishan Med. Coll. 1995, 16, 298–300. [Google Scholar]
  11. Yang, J.; Liu, Y.; Wang, M. Study on the active constituents of Thymus mongolicus Ronn. and the molecular mechanism of promoting blood circulation and removing blood stasis. TCM Res. 2011, 24, 2–4. [Google Scholar]
  12. Hu, C.; Li, Z.; Xue, D.; Chen, Y.; Yang, J. Study on chemical constituents of volatile oil from wild thyme (abstract). J. Ningxia Med. Coll. 1987, 9, 102–103. [Google Scholar]
  13. Zhang, H.; Wang, Y.; Zhang, Z. Study on chemical constituents of essential oil from Thymus mongolicus Ronn. Acta Bot. Boreal. Occid. Sin. 1992, 13, 245–248. [Google Scholar]
  14. Rasooli, I.; Owlia, P. Chemoprevention by thyme oils of Aspergillus parasiticus growth and aflatoxin production. Phytochemistry 2005, 66, 2851–2856. [Google Scholar] [CrossRef] [PubMed]
  15. Boughendjioua, H.; Djeddi, S. Quality attributes of the thyme (Thymus numidicus Poiret.) essential oil. J. Plant Sci. 2018, 6, 12–15. [Google Scholar]
  16. Guillen, M.; Manzanos, M. Study of the composition of the different parts of a Spanish Thymus vulgaris L. plant. Food Chem. 1998, 63, 373–383. [Google Scholar] [CrossRef]
  17. Fan, L.; Yang, H. Study on the components and antibacteria activity of Thymus mongolicus Ronn. essential oil. Contemp. Chem. Ind. 2014, 43, 701–703. [Google Scholar]
  18. Zhang, Z. Identification and determination of thyme aromatic oil. Acta Bot. Boreal. Occid. Sin. 2004, 13, 151–153. [Google Scholar]
  19. European Pharmacopoeia Commission. European Pharmacopoeia; Druckerei, C.H., Ed.; Beck.: Nördlingen, Germany, 2014; Volume 9, pp. 1538–1560. [Google Scholar]
  20. Pei, X.; Pei, M.; Li, H.; Pei, X.; Lu, Y.; Chen, Y.; Li, Y. Content determination of thymol and carvacrol from Herba Thyma by GC. Chin. J. Exp. Tradit. Med. Form. 2013, 19, 132–134. [Google Scholar]
  21. Ji, L.; Wang, F.; Liu, Y.Y.; Tong, Y.; Li, X.D.; Feng, X.F.; Huang, L.Q.; Zhou, G.P. Determination of carvacrol and thymol in Mosla chinensis by HPLC. China J. Chin. Mater. Med. 2004, 29, 8–10. [Google Scholar]
  22. Xu, Y.; Sun, Q.; Huang, J.; Tan, X. The characters of Waters ACQUITY UPC2 system. J. Mod. Instrum. 2012, 18, 45–48. [Google Scholar]
  23. Gong, X.; Qi, N.; Wang, X.; Li, J.; Lin, L. A New Method for Determination of α-Tocopherol in Tropical Fruits by Ultra Performance Convergence Chromatography with Diode Array Detector. Food Anal. Methods 2014, 7, 1572–1576. [Google Scholar] [CrossRef]
  24. Jiang, H.; Yang, L.; Xing, X.; Yan, M.; Guo, X.; Yang, B.; Wang, Q.H.; Kuang, H.X. Development of an analytical method for separation of phenolic acids by ultra-performance convergence chromatography (UPC 2) using a column packed with a sub-2-μm particle. J. Pharm. Biomed. Anal. 2018, 153, 117–125. [Google Scholar] [CrossRef] [PubMed]
  25. Kim, H.S.; Choi, G.; Lee, A.Y. Ultra-performance convergence chromatography method for the determination of four chromones and quality control of Saposhnikovia divaricata (Turcz.) Schischk. J. Sep. Sci. 2018, 41, 1682–1690. [Google Scholar] [CrossRef] [PubMed]
  26. Kim, H.S.; Moon, B.C.; Choi, G.; Lee, A.Y. Ultra-performance convergence chromatography for the quantitative determination of bioactive compounds in Aralia continentalis Kitagawa as quality control markers. J. Sep. Sci. 2017, 40, 2071–2079. [Google Scholar] [CrossRef]
  27. Qi, N.; Gong, X.; Feng, C.; Wang, X.; Xu, Y.; Lin, L. Simultaneous analysis of eight vitamin E isomers in Moringa oleifera Lam. leaves by ultra performance convergence chromatography. Food Chem. 2016, 207, 157–161. [Google Scholar] [CrossRef]
  28. Chinese Pharmacopoeia Commission. Chinese Pharmacopoeia; The Stationery Office: London, UK, 2015; Volume 4, pp. 374–377. [Google Scholar]
  29. Farré, M.; Perez, S.; Gonçalves, C.; Alpendurada, M.; Barceló, D. Green analytical chemistry in the determination of organic pollutants in the aquatic environment. TrAC Trends Anal. Chem. 2010, 29, 1347–1362. [Google Scholar] [CrossRef]
  30. Marek, T.; Jacek, N. Direct chromatographic methods in the context of green analytical chemistry. TrAC Trends Anal. Chem. 2012, 35, 67–73. [Google Scholar]
Figure 1. Chemical structures of thymol (Thl) and carvacrol (Cal) (both C10H14O).
Figure 1. Chemical structures of thymol (Thl) and carvacrol (Cal) (both C10H14O).
Molecules 25 00502 g001
Figure 2. (A) UPC2 chromatogram of the mixed standard solutions. (B) Typical UPC2 chromatogram of the T. mongolicus extract. (C) Typical UPC2 chromatogram of the T. przewalskii extract. Note: 1, thymol (Thl); 2, carvacrol (Cal).
Figure 2. (A) UPC2 chromatogram of the mixed standard solutions. (B) Typical UPC2 chromatogram of the T. mongolicus extract. (C) Typical UPC2 chromatogram of the T. przewalskii extract. Note: 1, thymol (Thl); 2, carvacrol (Cal).
Molecules 25 00502 g002
Table 1. Information about Thymi herba samples.
Table 1. Information about Thymi herba samples.
SampleSourcePurchase/Collection dateSpecies
T-1Bozhou Sanyitang Pharmaceutical Co., Ltd., Anhui Province2017.9.5T. przewalskii
T-2Liupan Shan Town, Ningxia Hui Autonomous Region2017.9.23T. mongolicus
T-3Anguo Medicinal Material Market, No. 1, Hebei Province2017.8.12T. mongolicus
T-4Kangmei International City of Traditional Chinese Medicine, Anhui Province2017.10.24T. przewalskii
T-5Shihezi City, Xinjiang Autonomous Region2018.1.11T. przewalskii
T-6Delong County, Ningxia Hui Autonomous Region2018.1.11T. mongolicus
T-7Guyuan City, No. 1, Ningxia Hui Autonomous Region2018.1.18T. mongolicus
T-8Guyuan City, No. 2, Ningxia Hui Autonomous Region2018.1.18T. mongolicus
T-9Haiyuan County, Zhongwei City, Ningxia Hui Autonomous Region2018.1.18T. przewalskii
T-10Anguo Medicinal Material Market, No. 2, Hebei Province2018.3.26T. mongolicus
T-11Maquan Village, Guyuan City, Ningxia Hui Autonomous Region2018.6.8T. mongolicus
T-12Zhangyi Village, Guyuan City, Ningxia Hui Autonomous Region2018.6.8T. mongolicus
T-13Songwa Village, Guyuan City, Ningxia Hui Autonomous Region2018.6.6T. mongolicus
T-14Pengyang County, Guyuan City, Ningxia Hui Autonomous Region2018.6.5T. mongolicus
T-15Dadian Village, Guyuan City, Ningxia Hui Autonomous Region2018.6.3T. mongolicus
T-16Xintaozi Village, Guyuan City, Ningxia Hui Autonomous Region2018.6.6T. mongolicus
T-17Zhongzhuang Village, Guyuan City, Ningxia Hui Autonomous Region2018.6.2T. mongolicus
T-18Yanni Village, Guyuan City, Ningxia Hui Autonomous Region2018.6.3T. mongolicus
T-19Tuoxiang Village, Guyuan City, Ningxia Hui Autonomous Region2018.6.9T. mongolicus
T-20Zhonghe Village, Guyuan City, Ningxia Hui Autonomous Region2018.6.10T. mongolicus
Table 2. Parameters of the ultraperformance convergence chromatography (UPC2) method for determination of Thymol (Thl) and Carvacrol (Cal) in Thymi herba.
Table 2. Parameters of the ultraperformance convergence chromatography (UPC2) method for determination of Thymol (Thl) and Carvacrol (Cal) in Thymi herba.
StandardRT (min)Calibration CurverLOD (ng)LOQ (ng)Linear Range (ng)
Thymol2.109y = 602.02x0.99981.312.635.25–168.00
Carvacrol2.263y = 606.05x + 224.730.99991.573.146.28–201.00
Calibration curve: y = mx + b, where y is the integrated peak area and x is the concentration in ng. RT, retention time; LOD, limit of detection; LOQ, limit of quantification.
Table 3. Validation of the method for determination of thymol (Thl) and carvacrol (Cal) in Thymi herba.
Table 3. Validation of the method for determination of thymol (Thl) and carvacrol (Cal) in Thymi herba.
AnalytePrecision (n = 6) (RSD, %)Repeatability (n = 6) (RSD, %)Stability (RSD, %)
IntradayInterday
Thymol1.160.711.391.86
Carvacrol0.391.501.371.90
Table 4. Recovery of thymol (Thl) and carvacrol (Cal) as determined by the standard addition method (n = 6).
Table 4. Recovery of thymol (Thl) and carvacrol (Cal) as determined by the standard addition method (n = 6).
CompoundsSample Weight (g)Original (mg)Spiked (mg)Found (mg)Recovery (%)Average recovery (%)RSD (%)
Thl1.50410.18170.09020.2745102.887199.18652.4016
1.50560.18190.09020.270798.5150
1.50000.18120.09020.2732102.0505
1.50060.18130.18030.3618100.1283
1.50430.18170.18030.3634100.7310
1.50190.18150.18030.357297.4893
1.50980.18240.27050.445197.1175
1.50010.18120.27050.446097.8726
1.50190.18150.27050.440895.8873
Cal1.50410.38400.18540.551390.206888.72021.9644
1.50560.38440.18540.546587.4386
1.50000.38300.18540.545887.8305
1.50060.38310.37090.723591.7837
1.50430.38410.37090.721190.8680
1.50190.38350.37090.707287.2880
1.50980.38550.55630.871487.3473
1.50010.38300.55630.869987.5144
1.50190.38350.55630.874288.2043
Table 5. Thymol (Thl) and carvacrol (Cal) contents of T. mongolicus and T. przewalskii (n = 2).
Table 5. Thymol (Thl) and carvacrol (Cal) contents of T. mongolicus and T. przewalskii (n = 2).
SampleContent (mg/g)
ThlCal
T-10.16430.2725
T-20.10000.1504
T-30.15850.2192
T-40.24580.3235
T-50.24130.2775
T-60.13000.6159
T-70.09590.5832
T-80.06610.5377
T-90.08550.2051
T-100.19560.2023
T-110.10060.5162
T-120.18030.2128
T-130.06950.0904
T-140.19900.2783
T-150.15180.1439
T-160.15770.1590
T-170.15730.1456
T-180.08290.1680
T-190.12030.2569
T-200.22370.2590
Table 6. Determination of thymol (Thl) and carvacrol (Cal) contents of T. mongolicus by gas chromatography (GC) [20].
Table 6. Determination of thymol (Thl) and carvacrol (Cal) contents of T. mongolicus by gas chromatography (GC) [20].
SampleContent (mg/g)
ThlCal
10.2550.121
20.2430.134
30.2390.118
40.2160.147
50.2400.131
60.2380.122
70.1202.520
80.2121.298

Share and Cite

MDPI and ACS Style

Chang, X.; Sun, P.; Ma, Y.; Han, D.; Zhao, Y.; Bai, Y.; Zhang, D.; Yang, L. A New Method for Determination of Thymol and Carvacrol in Thymi herba by Ultraperformance Convergence Chromatography (UPC2). Molecules 2020, 25, 502. https://doi.org/10.3390/molecules25030502

AMA Style

Chang X, Sun P, Ma Y, Han D, Zhao Y, Bai Y, Zhang D, Yang L. A New Method for Determination of Thymol and Carvacrol in Thymi herba by Ultraperformance Convergence Chromatography (UPC2). Molecules. 2020; 25(3):502. https://doi.org/10.3390/molecules25030502

Chicago/Turabian Style

Chang, Xiaoqiang, Peng Sun, Yue Ma, Dongchen Han, Yifan Zhao, Yue Bai, Dong Zhang, and Lan Yang. 2020. "A New Method for Determination of Thymol and Carvacrol in Thymi herba by Ultraperformance Convergence Chromatography (UPC2)" Molecules 25, no. 3: 502. https://doi.org/10.3390/molecules25030502

Article Metrics

Back to TopTop