Abstract

Hydrogen-producing acetogens (HPA) have a transitional role in anaerobic wastewater treatment. Thus, bioaugmentation with HPA cultures can enhance the chemical oxygen demand (COD) removal efficiency and CH4 yield of anaerobic wastewater treatment. Cultures with high degradation capacities for propionic acid and butyric acid were obtained through continuous subculture in enrichment medium and were designated as Z08 and Z12. Bioaugmentation with Z08 and Z12 increased CH4 production by glucose removal to 1.58. Bioaugmentation with Z08 and Z12 increased the COD removal rate in molasses wastewater from 71.60% to 85.84%. The specific H2 and CH4 yields from COD removal increased by factors of 1.54 and 1.63, respectively. Results show that bioaugmentation with HPA-dominated cultures can improve CH4 production from COD removal. Furthermore, hydrogen-producing acetogenesis was identified as the rate-limiting step in anaerobic wastewater treatment.

1. Introduction

High-strength organic wastewater and municipal sludge can be efficiently treated through anaerobic processes, which produce CH4 as the main product [1]. The microbial cultures used in anaerobic wastewater treatment are highly complex and include fermentative bacteria, hydrogen-producing acetogens (HPA), and methanogenic bacteria (MB) [2, 3]. HPA species are applied in anaerobic wastewater treatment as an alternative to MB, sulfate-reducing bacteria, and other hydrogen-consuming bacteria [4]. However, only a few strains of HPA have been isolated and purified because the species are obligate or facultative anaerobe. HPA mainly converts volatile fatty acids (VFAs) and ethanol into acetic acid, H2, and CO2 [5, 6]. The metabolic products of HPA, in turn, promote CH4 production by MB [7].

Propionate acid tends to accumulate in high-strength organic wastewater, and the COD removal efficiency from wastewater decreases with increasing influent COD [8]. Previous studies attributed this phenomenon to methanogenesis because MB has a slow growth rate, narrow ecological niche, and stringent requirements for living conditions [9, 10]. In addition, VFA degradation is the rate-limiting step in anaerobic wastewater treatment because it is subject to the acetic acid degradation pathway and can decelerate and decrease acetic acid conversion [10, 11]. The degradation of propionate and butyrate acids by HPA cannot proceed spontaneously under normal conditions because it requires energy consumption [6]. By contrast, the terminal product CH4 can be spontaneously produced under normal conditions when acetic acid, H2, and CO2 are present in sufficient amounts [6]. This phenomenon indicates that the substrate conversion capacity of MB is higher than that of HPA. Therefore, hydrogen-producing acetogenesis likely exerts considerable influence on the effectiveness of anaerobic wastewater treatment. The growth rate of HPA is as typically as slow as that of MB [12, 13]. HPA, however, requires more rigorous living conditions than MB [14]. Thus, HPA could potentially become the rate-limiting factor in anaerobic wastewater treatment under certain conditions.

HPA is a strictly anaerobic eubacteria, and most HPA species are mutualists [15, 16]. The latter characteristic implies that the growth and metabolism of HPA completely depend on the presence of other microorganisms, such as methanogens [17]. McInerney and Bryant [4] and McInerney et al. [12] isolated four HPA strains that can degrade butyrate; comprehensively analyzed the growth, metabolism, phosphatidic acid composition, and nutrition of the isolates; and established the Syntrophomonadaceae family through 16S rRNA sequencing analysis [18]. Medium-temperature propionic acid-oxidizing bacteria [19] have been recently obtained in fumarate culture medium. These bacteria exhibited remarkable activity in propionate oxidation associated with sulfate reduction. Syntrophobotulus glycolicus, Syntrophothermus lipocalidus, Sporomusa sphaeroides, and Moorella thermoacetica have been subsequently isolated [2023]. However, given that pure HPA cultures are difficult to obtain, the ability of a HPA-dominated coculture of anaerobic microbes to enhance CH4 production and contaminant removal should be investigated [10, 24].

The effectiveness of anaerobic wastewater treatment depends mainly on the enrichment of functional microorganisms [25, 26]. The performance of anaerobic wastewater treatment can be improved through bioaugmentation, which involves the addition of specific strains or dominated flora to the reaction system [27]. Bioaugmentation accelerates the start-up and maintains the stability of bioreactors and enhances the conversion rate of complex substrates. The methane production increased at least 38% [26, 27] and has increased total biogas and CH4 yields through COD removal [13, 14]. In addition, the ability of propionate-oxidizing and butyrate-oxidizing HPA to enhance CH4 production has been investigated.

In this work, cultures dominated by propionate-oxidizing and butyrate-oxidizing HPA were obtained from anaerobic sludge through enrichment culture. The organic substrate degradation capability of the propionate-oxidizing and butyrate-oxidizing microflora was investigated through batch cultures. The enhancement in CH4 production and COD removal rates by bioaugmentation with the mixed HPA culture was evaluated.

2. Materials and Methods

2.1. Seed Sludge and Enrichment Medium

The original anaerobic activated sludge used to screen for HPA-dominated cultures was collected from an anaerobic baffled reactor [28]. The enrichment medium, micronutrient solution, and vitamin solution were prepared as described by Liu et al. [13] and Wang et al. [14]. 10 mL of anaerobic sludge sampled and inoculated to 300 mL serum bottles, and each bottle contained 100 mL propionic acid or butyric acid enrichment medium. The serum bottles were purged with nitrogen gas for 20 min and then cultivated under shaking at 130 r/min and 35°C. Only when the consumption of propionic acid or butyric acid was up to 85% that 10 mL of bacterial suspension was extracted and injected as inocula for the subsequent batch cultures. The successful enrichment of HPA-dominated cultures (Z08 for HPA-dominated culture that oxidized propionic acid; Z12 for HPA-dominated culture that oxidized butyric acid) depended on the rate of CH4 production from propionic acid and butyric acid [13, 14].

2.2. Glucose and Molasses Wastewater

Glucose wastewater contained 5000 mg/L of glucose and was modified with 1000 mg/L of NH4Cl, 600 mg/L of NaCl, 200 mg/L of FeCl2, 300 mg/L of KH2PO4, and 300 mg/L of K2HPO4. The COD of molasses wastewater was 8000 mg/L. To maintain the bioactivity of the anaerobic activated sludge, NH4Cl and K2HPO4 were added at a COD : N : P ratio of 500 : 8 : 1. NaHCO3 was used to adjust the initial pH value of the wastewater to 7.8–8.0.

2.3. Bioaugmentation Batch Test

Bioaugmentation batch tests were conducted to evaluate the effect of HPA-dominated microflora. Four serum bottles (500 mL) were used for glucose degradation. Each serum bottle contained 300 mL of glucose wastewater and 30 mL of anaerobic activated sludge. The original mixed liquor volatile suspended solids (MLVSS) of anaerobic sludge, Z08, and Z12 was 12400 mg/L, 2500 mg/L, and 3600 mg/L, respectively; in particular, the MLVSS of anaerobic sludge, Z08, and Z12 were uniformly diluted to 350 mg/L to maintain the initial MLVSS which was equal in each sample. Each serum bottle contained biomass at the rate of 40 mg MLVSS/L. The experimental scheme for bioaugmented glucose wastewater treatment was designed as follows: FH1 (30 mL of anaerobic activated sludge), FH2 (27 mL of anaerobic activated sludge and 3 mL of Z08), FH3 (26 mL of anaerobic activated sludge and 4 mL of Z12), and FH4 (27 mL of anaerobic activated sludge, 1.8 mL of Z08, and 1.2 mL of Z12). Four serum bottles (500 mL) were utilized for normal molasses wastewater treatment. Each serum bottle contained 240 mL of normal molasses wastewater and 40 mL of anaerobic activated sludge. Each serum bottle contained biomass in the form of MLVSS at the rate of 50 mg MLVSS/L. The experimental scheme for bioaugmented molasses wastewater treatment was designed as follows: QJ1 (40 mL of anaerobic activated sludge), QJ2 (36 mL of anaerobic activated sludge and 4 mL of Z08), QJ3 (35 mL of anaerobic activated sludge and 5 mL of Z12), and QJ4 (36 mL of anaerobic activated sludge, 2.0 mL of Z08, and 2.0 mL of Z12). All serum bottles were cultivated under shaking at 130 r/min and 35°C.

2.4. Iodonitrotetrazolium Chloride–Dehydrogenase

Dehydrogenase is an organic macromolecule that is secreted by microorganisms. It is used as an index for the evaluation of the bioactivity of anaerobic activated sludge [29]. Iodonitrotetrazolium chloride (INT) has low redox potential (+90 mV). This characteristic indicates that INT has high electron affinity [30] and suggests that dehydrogenase activity can be measured on the basis of INT activity. Dehydrogenase activity (UI) can be calculated using where is the dehydrogenase activity (μmol INT/g·min), denotes the absorbance of the extract liquor, and represents biomass content (MLVSS, mg).

2.5. Analytical Methods

COD and MLVSS values were measured in accordance with standard methods [31]. Glucose was measured through the phenol–sulfuric acid method [32]. The biogas yield in each bottle was measured periodically using 5 and 50 mL syringes, and biogas constituents (H2, CO2, and CH4) were characterized through gas chromatography (Lunan SC-7, China). The components of ethanol and VFAs (acetic acid, propionic acid, and butyric acid from the liquid phase of the reaction system) were analyzed through gas chromatography (AAC GC-112, China). The experiment was run in triplicate.

3. Results and Discussion

3.1. Enrichment of HPA
3.1.1. Propionate-Oxidizing HPA

Z08, a mixed culture dominated by propionate-oxidizing HPA, was successfully obtained after ten generations of continuous subculture. As listed in Supplementary Table 1, the acetic acid yield and accumulative H2 yield was 1007.9 mg/L and 49.2 mL, respectively, indicating that the propionate-oxidizing HPA performed well in propionic acid degradation and supplied sufficient substances for methane production. The conversion rate of propionic acid was 18.5 mmol/gMLVSS·d, and the rate of methane production from propionic acid was 0.49. As shown in Figure 1(a), bioaugmentation with Z08 rapidly decreased propionic acid concentration from 8436.71 mg/L to 8083.74 mg/L and increased acetic acid concentration from 524.61 mg to 701.43 mg. This result indicates that Z08 has good adaptation performance. After 9 days of inoculation with Z08, propionic acid concentration significantly decreased from 8083.74 mg/L to 2008.91 mg/L, whereas acetic acid concentration increased from 701.43 mg/L to 2251.49 mg/L. The H2 and CO2 contents of the biogas increased from 0.06% to 0.09% and from 11.53% to 18.76% (Figure 1(b)), respectively, whereas CH4 content sharply increased to 45.42%. However, the degradation of propionic acid slowed down and decreased to 351.14 mg/L after 30 days of subculture. The accumulated acetic acid concentration was 1203.53 mg/L. The cumulative biogas yield was 161 mL, and H2, CH4, and CO2 contents were 0.12%, 49.14%, and 11.27%, respectively. In addition, the terminal pH value of the entire reaction system stabilized at 7.30–7.40. This pH range is suitable for enhanced propionic acid removal and CH4 production [33]. The average degradation rate of propionic acid under bioaugmentation with Z08 was 269.5 mg/L·d. The conversion rate of propionic acid was 22.1 mmol/gMLVSS·d, and the rate of CH4 production from propionic acid was 0.41.

Propionic acid degradation can be divided into three stages on the basis of two distinct turning points. The first stage is the adaptation stage and occurred from days 0 to 8 of degradation. During this stage, propionic acid degradation was low. The second stage occurred from days 9 to 20 of degradation. During this stage, the microorganisms in Z08 adapted to the new living conditions and actively degraded propionic acid. Most of propionic acid was consumed through the synergistic action of MB [13, 34]. The third stage occurred from days 21 to 30 of degradation. As the propionic acid content of the culture medium decreased, microbial activity was reduced because the microorganisms in Z08 competed with one another. In addition, excessive acetic acid generation during stage 2 triggered feedback inhibition as shown by (2). Feedback inhibition then decelerated propionic acid degradation [35]. However, the bioactivity of MB in Z08 was not inhibited, and propionic acid concentration decreased again when acetic acid was converted to CH4 by MB.

3.1.2. Butyrate-Oxidizing HPA

Z12, a mixed culture dominated by butyrate-oxidizing HPA, was successfully obtained after seven generations of continuous subculture. As listed in Supplementary Table 2, the acetic acid yield and accumulative H2 yield was 900.7 mg/L and 51.6 mL, respectively, indicating that the butyrate-oxidizing HPA presented good capacity in butyric acid degradation and provided sufficient substances for methane production. The conversion rate of butyric acid was 15.5 mmol/gMLVSS·d, and the rate of methane production from butyric acid was 0.75. As illustrated in Figure 2(a), over 3 days of inoculation with Z12, butyric acid concentration decreased from 7063.64 mg/L to 5727.3 mg/L, and acetic acid concentration increased from 659.88 mg/L to 788.59 mg/L. H2, CH4, and CO2 concentrations in biogas increased by 0.06%, 18.68%, and 4.64% (Figure 2(b)), respectively, indicating that HPA in Z12 had begun to degrade butyric acid into acetic acid, H2, and CO2 to provide substrates for MB in Z12. However, butyric acid degradation slowed down from days 4 to 6 along with the treatment process, and butyric acid content remained at 5500 mg/L. Subsequently, butyric acid concentration sharply decreased from 5457.28 mg/L to 776.29 mg/L, and the cumulative acetic acid concentration peaked at 1762.43 mg/L. The H2 content of the biogas peaked on day 9, and CH4 and CO2 content also rapidly increased. Butyric acid concentration decreased to 211.83 mg/L on day 24, whereas acetic acid concentration gradually decreased on day 21. Moreover, the H2 content of the biogas also declined. The terminal concentrations of butyric acid and acetic acid were 211.83 and 827.65 mg/L, respectively. The cumulative biogas yield was 191 mL, and CH4 and CO2 contents reached as high as 60.76% and 16.45%, respectively. The final pH value of the whole reaction system stabilized at 7.40–7.50, which is desirable for good butyric acid removal and CH4 production. The average degradation rate of butyric acid under bioaugmentation with Z12 was 285.5 mg/L·d. The conversion rate of butyric acid was 15.8 mmol/gMLVSS·d, and the rate of CH4 production from butyric acid was 0.74.

Although the process of butyric acid degradation can also be divided into three phases, it differed from that of propionic acid degradation. Stage I, the acclimation period of Z12, occurred during days 1 to 3 of degradation and was shorter than the acclimation period of Z08. During this stage, Z12 rapidly degraded butyric acid, and acetic acid content increased. During stage II (days 4–6), the degradation rate of butyric acid declined (Figure 2(a)). In contrast to HPA, MB displayed good bioactivity in the reaction system because the methane production rate kept increasing during this stage. The slight accumulation of acetic acid indicated that hydrogenotrophic methanogen was dominant in MB and the community structure of Z12 thus facilitated H2 consumption, which further enhanced butyric acid degradation by HPA [36]. During stage III (days 7–24), HPA efficiently converted butyric acid to acetic acid and H2, and the acetic acid and H2 contents of the reaction system increased temporarily (Figure 2(b)). By contrast, acetic acid concentration remained low because of the good substrate conversion efficiency of MB.

3.1.3. Rate-Limiting Step of Anaerobic Wastewater Treatment

In general, acetic acid degradation by MB is an energy-reducing reaction that can occur spontaneously under standard conditions. By contrast, as shown by (3), butyric acid degradation by HPA cannot occur spontaneously under standard conditions [35]. This behavior implies that the degradation of acetic acid by MB is easier than that of butyric acid by HPA.

Although hydrogenotrophic methanogens could not deplete H2 in time and decrease pH2, acetogenic methanogens converted acetic acid into CH4 in the culture medium [37]. Therefore, the reduction in acetic acid concentration could promote the degradation of butyric acid.

Similarly, propionate degradation by HPA cannot proceed spontaneously under normal conditions because this reaction requires energy consumption [6]. Nevertheless, propionic acid degradation could be enhanced by decreasing H2 concentration. Furthermore, propionic acid degradation requires a low system pH2 given its high standard Gibbs-free energy [38, 39]. In accordance with hydrogen partial pressure theory, propionic acid was rapidly degraded when pH2 was low, and propionic acid degradation slowed down when H2 accumulated (Figure 1).

Moreover, the acetic acid concentration of the culture medium was maintained at approximately 1000 mg/L throughout the reaction (Figures 1(a) and 2(a)) because of the presence of MB, which could release feedback inhibition on propionic and butyric acid accumulation. Although the degradation of butyric acid in stage II was less and thus resulted in the accumulation of acetic acid (Figures 2(a) and 2(b)), methane production still increased, emphasizing that the rate-limiting step was not methanogenesis. The high CH4 yield implied the good bioactivity of MB and that the rate-limiting step of propionic acid and butyric acid degradation can be attributed to HPA [8, 40].

3.2. Performance of Mixed HPA Culture in Glucose Degradation

The biogas yield, maximum specific CH4 production rate, and CH4 production rate from glucose in FH4 were higher than those in FH1, FH2, and FH3 (Table 1). The contents of terminal VFAs (acetic acid, propionic acid, and butyric acid) in FH4 (139, 109, and 297 mg/L) were markedly lower than those in FH3 (189, 149, and 433 mg/L). These results indicated that the mixed HPA culture and the anaerobic activated sludge exhibit high glucose conversion rates. Bioaugmentation enhanced the rate of CH4 production from glucose, and the variation in pH corresponded to the variation in glucose degradation by the dominant microflora. The initial pH was maintained at 8.0. The acidification ratio reached 42.3% as glucose degradation proceeded [41], causing the pH value to decrease to 5.7. This pH value is unfavorable for MB [33]. Thereafter, the pH value recovered to 7.1 through the synergy of HPA and MB. This effect was particularly pronounced under high acetic acid conversion rates. The two types of dominant bacteria (Z08 and Z12) grew independently and performed specific microbial activities. The promoting effects of these activities on high-strength organic wastewater treatment require further study.

3.3. Performance of Mixed HPA Culture in Normal Molasses Wastewater Treatment
3.3.1. Biogas Components and Yields

As shown in Figure 3, the majority of the substrates in molasses wastewater were converted to H2, CO2, and CH4. These results indicate that bioaugmentation improves resource recovery. All reaction systems provided high H2 yields during the initial stages of treatment, and QJ4 provided the highest H2 yield (23.76%) among all reaction systems. H2 content remained as high as 15% for the first 72 h of treatment and subsequently declined. By contrast, CH4 was not detected, indicating that homoacetogenic bacteria in the reaction system utilized H2 and CO2 to produce acetic acid [42]. CH4 was detected after 120 h in QJ3 and QJ4 and after 145 h in QJ1 and QJ2. These results imply that the bioactivity of the butyric-oxidizing HPA is higher than that of the propionic-oxidizing HPA [35]. The CH4 contents of the QJ2, QJ3, and QJ4 systems remained above 25% during acetogenesis, and the CH4 content of QJ4 reached as high as 37%. However, the CH4 content of QJ1 was only approximately 15% because HPA has low acetic acid, H2, and CO2 conversion capacities. The anaerobic activated sludge modified with the mixed HPA culture could produce sufficient substrates for MB because ethanol, propionic acid, and butyric acid, as indicated by the quick and efficient conversion of the substrates into acetic acid, H2, and CO2.

The biogas yields of QJ2, QJ3, and QJ4 were 183, 226, and 252 mL, respectively, and were moderately higher than that of QJ1. The cumulative H2 yields of QJ1, QJ2, QJ3, and QJ4 were 48.93, 51.21, 56.27, and 89.43 mL, respectively. The cumulative CH4 yields of QJ1, QJ2, QJ3, and QJ4 were 32.33, 45.97, 49.14, and 61.91 mL, respectively. These results collectively imply that HPA bioaugmentation increases H2 and CH4 production and improves molasses conversion. As shown in Figure 4, the specific rates of H2 and CH4 yields from COD removal under bioaugmentation with the mixed HPA culture in QJ4 had increased by a factor of 1.54 and 1.63 compared with those in QJ1. The experimental results show that bioaugmentation has a detectable effect and that it can effectively improve the efficiency of anaerobic wastewater treatment.

3.3.2. Terminal Soluble Products

As illustrated in Figure 5, the degradation of molasses wastewater by anaerobic activated sludge and HPA was inconsistent with that of glucose wastewater. Ethanol could be detected after 6 h of glucose degradation and after 72 h of molasses degradation. These results indicate that the mixed HPA culture can effectively convert ethanol into acetic acid, H2, and CO2 [43]. In addition, ethanol was not detected in QJ, suggesting that bioaugmentation with Z08 and Z12 promotes ethanol conversion from molasses and thereby decreases the possibility of propionic acid and butyric acid conversion from molasses. The conversion of ethanol into acetic acid is a spontaneous reaction [35]. Therefore, the substrate conversion rate increased in QJ2, QJ3, and QJ4 under relatively high ethanol content (500 mg/L). HPA-dominated microflora has a transitional role in anaerobic wastewater treatment [34, 44], thus enhancing resource recovery (Figure 4).

In QJ1, no characteristics of VFA degradation were observed, and the terminal acetic acid, propionic acid, and butyric acid contents were 1000, 780, and 770 mg/L, respectively, after 500 h of degradation. By contrast, in QJ2, QJ3, and QJ4, propionic and butyric acid degradation showed clear trends and improved as acetic acid content increased. The terminal acetic acid, propionic acid, and butyric acid contents were 1751, 230, and 847 mg/L in QJ2, respectively; 2047, 220, and 590 mg/L in QJ3, respectively; and 1841, 375, and 580 mg/L in QJ4, respectively. The propionic acid and butyric acid contents in QJ2, QJ3, and QJ4 were significantly lower than those in QJ1 because propionic acid and butyric acid could be effectively degraded by the HPA-dominated culture, and microbial metabolic products could be utilized by MB. Moreover, at 72–120 h of the reaction, acetic acid content considerably increased, H2 content decreased, and CH4 was not detected in QJ4 (Figures 3(d) and 5(d)). These results imply that homoacetogenesis has occurred in the reaction system. The initial pH value of the reaction system was 8.10, which then sharply decreased to 4.50 within the first 48 h of the reaction because a large amount of VFAs were produced through acidogenesis [6, 41]. Correspondingly, H2 conversion increased. Thereafter, given the synergism of HPA and MB, propionic acid, butyric acid, acetic acid, H2, and CO2 were successively utilized, and the pH value of the reaction system was maintained at approximately 7.00.

3.3.3. Correlation of Specific Dehydrogenase Activity and COD Removal

The COD removal efficiencies in QJ1, QJ2, QJ3, and QJ4 were 71.7%, 80.3%, 83.5%, and 85.8%, respectively, after 500 h of anaerobic treatment. In QJ4, bioaugmentation with the mixed HPA culture increased substrate degradation and CH4 production. In addition, specific dehydrogenase activity was measured on the basis of INT throughout the process of molasses wastewater treatment. The specific dehydrogenase activity in QJ4 was significantly higher than that in QJ1, indicating that bioaugmentation with Z08 and Z12 improves microbial activity. The correlation coefficients between specific dehydrogenase activity and COD removal in the four systems were 0.9609, 0.9924, 0.9841, and 0.9776, as calculated by the CORREL function (Table 2). The experimental results demonstrate that the INT-specific dehydrogenase activity of anaerobic activated sludge is highly correlated with COD removal rate. Thus, the bioactivity of anaerobic activated sludge can be objectively and accurately reflected by INT-specific dehydrogenase activity [45].

4. Conclusion

Mixed cultures dominated by propionic- and butyric-oxidizing HPA were obtained through more than seven generations of continuous subculture. The rate of CH4 production from propionic acid and butyric acid were 0.41 and 0.74, respectively. Hydrogen-producing acetogenesis was identified as the rate-limiting factor of anaerobic wastewater treatment. Inoculation with the mixed cultures of Z08 and Z12 increased the biogas yield, maximum specific CH4 production rate, and CH4 production rate of glucose and molasses wastewater treatment, as well as increased the specific rates of H2 and CH4 yield from COD removal by a factor of 1.54 and 1.63, respectively. The INT-specific dehydrogenase activity of anaerobic activated sludge was highly correlated with COD removal efficiency.

Data Availability

The data used to support the findings of this study are available from the corresponding author upon request.

Conflicts of Interest

The authors declare that they have no conflicts of interest.

Acknowledgments

The study was supported by the National Natural Science Foundation of China (Grant no. 51478141), the Major Science and Technology Program for Water Pollution Control and Treatment (2017ZX07201-001), the State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology (Grant no. 2016DX06), and the Fundamental Research Funds for the Central Universities (Grant no. JUSRP51512).

Supplementary Materials

Table S1: metabolic characteristics of the subcultured microflora that oxidize propionic acid. Table S2: metabolic characteristics of the subcultured microflora that oxidize butyric acid. (Supplementary Materials)