样式: 排序: IF: - GO 导出 标记为已读
-
Effect of Aluminum, Copper and Manganese on the Structure and Properties of Cast Irons Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-20 N. V. Stepanova, R. I. Mikhalev, T. D. Tarasova, S. S. Volkov
-
Effect of Ni Addition on the Metallurgical and Mechanical Properties of WC – 10Co – 4Cr Laser Cladding Surfaces on Mild Steel Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-20
The effect of laser cladding process technological parameters, as well as of the addition of nickel (5 – 15 wt.%) on the structure and mechanical properties of WC – 10Co – 4Cr laser cladding on mild steel, has been studied. The most effective laser cladding process parameters were determined when applying single-pass clad tracks and tracks with 50% overlap. The microstructure and the phase composition
-
Effect of Pressure and Heating Temperature on the Structure and Mechanical Properties of Explosion-Welded Aluminum-Niobium Multilayer Composite Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-20 Yu. N. Malyutina, D. V. Lazurenko, E. A. Lozhkina
-
High-Resolution Characterization of Subunits in Nanostructured Bainite in High-Carbon Silicon Steel Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-19 Xin Zhang, Ying Yao, Ruiqi Guo, Tianyu Cui
-
Hot Deformation Behavior of Duplex Stainless Steel 2205 Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-19 Zhang Yong-jun, Dong Yuan, Hu Jie-ren, Zhang Hui, Han Jing-tao
-
Effect of Complex Alloying of the Damping Capacity of Mn – Cu Alloys in the Range of Amplitude-Independent Damping Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-19 S. B. Naumov, S. V. Ginne
-
Transformation of Niobium Carbide in Heat-Resistant Alloys Based on Fe – 25Cr – 35Ni at 900°C and 1150°C Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-19
Cross sections prepared using a focused ion beam are used for a transmission electron microscopy study of the microstructure and elemental composition of the intermetallic phases formed after long-term holding a 900 and 1150°C at the boundaries of dispersed particles of niobium carbide in a heat-resistant alloy of type HP40NbTi. Formation of a well-known G-phase is detected at 900°C. When the temperature
-
Raising the Wear Resistance of Chromium-Nickel Steel Surface-Hardened with Titanium Carbide Particles Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-19 E. G. Bushueva, E. A. Drobyaz, M. G. Golkovskii, A. A. Dudareva, I. K. Chakin
-
Review of Synthesis Methods, Microstructure and Properties of WC – Co-Based Hard Alloys Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-19 I. O. Kamolova, R. Kh. Saydakhmedov
-
Effect of Tempering Temperature on Mechanical and Corrosion Properties of Modified Martensitic Stainless Steel CA6NM Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-19 Mukhlis Agung Prasetyo, Nofrijon Sofyan, Faried M. Ridlo, Efendi Mabruri
-
Effect of Intermittent Water Spray Quenching on the Wear Resistance of Forged Grinding Balls Made of Steel 70SiMnCr Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-19 Zhixin Liu, Zhaoyang Song, Baoqi Wang
-
A Study of Decomposition of Supercooled Austenite in High-Strength Medium-Carbon Complexly Alloyed Cold-Resistant Steels Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-19 O. A. Kupriyanova, O. A. Nikitenko
-
Effect of Gas Atmosphere in Aluminobarothermal Synthesis on the Structure of Metal Matrix Composites Based on Fe – Cr – Mn – Mo Alloy Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-19
The structures of metal matrix composites based on the Fe – Cr – Mn – Mo system and fabricated by an aluminobarothermal process with the use of argon or nitrogen as the gas atmosphere in the reactor are compared. Chemical analysis for the content of the metals, nitrogen and oxygen in the samples is performed. The structure is studied in different conditions. The total hardness of the samples and the
-
Complex Deformation–Ion-Plasma Treatment of Steel 08Kh18N10T-Sh Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-17
The structure and properties of the surface and of the core of steel 08Kh18N10T-Sh subjected to radial forging and subsequent saturation by the method of ion-plasma nitriding are studied. It is shown that the complex deformation–ion-plasma treatment accelerates the nitriding process and provides a high level of strength of the surface and of the core of steel 08Kh18N10T-Sh. The lower the saturation
-
Diffusion Kinetics and Characterization of Fe2B Coatings Grown Thermochemically on Steel ASTM A709 Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-17 M. Ortiz-Dominguez, M. Keddam
-
Effect of Molybdenum Electron-Beam Cladding on the Heat and Wear Resistances of Surface Layers of Chromium-Nickel Austenitic Steel 12Kh18N9T Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-17 E. A. Pukhova, E. G. Byshueva, E. V. Domarov, B. B. Batyrov, V. G. Burov
-
Study and Characterization of Sigma Phase in Duplex Stainless Steel 2205 (03Kh22N6M2) Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-17 Reena Nagar, Krunal Kumar Patel, Anil Parmar
-
A Study of Gas-Saturated Layer After Oxidation of Alloy Ti6242S at 500 – 800°C Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-17 M. S. Kalienko, A. V. Zhelnina, A. A. Popov
-
Influence of Thermal Aging on Tensile-Plastic Flow Behavior of Indian Steel RAFM (F82H) Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-17 K. C. Sahoo, K. Laha
-
Effect of Natural Aging on the Structure and Properties of Steel 30KhGSA Hardened by Quenching and Partitioning Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2024-02-17 A. I. Popelyukh, S. V. Veselov, E. M. Tabakaev
-
Investigation of the Processes of Formation and Properties of Titanium Nickelides Welded on Titanium Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-27 A. I. Kovtunov, Yu. Yu. Khokhlov, V. V. El’tsov, L. V. Vershinin
-
Effect of Heat Treatment on the Hardness and Electrical Connectivity of an Aluminum Composite Reinforced with Al2O3 Nanoparticles Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-21
The effect of heat treatment modes on the microstructure, microhardness and electrical conductivity of an aluminum metal matrix composite (MMC) reinforced with Al2O3 nanoparticles in an amount of 2.5 wt.% is studied. The MMC is treated by quenching from 510, 530 or 550°C and subsequent artificial aging at 140, 160, 180, 200 or 220°C. The cast composite has a Vickers microhardness of 36 HV and an electrical
-
Investigation of the Effects of Overlapping Passes on Friction Stir Processed Aluminum Alloy 5083 Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-20 Lokesh Singh, Mazin Mahmood Yahya, Bharat Singh, Shankar Sehgal, Kuldeep K. Saxena, Kahtan A. Mohammed
-
Joining FE55006 Cast Iron and SAE 8620 Steel by Friction Hydro-Pillar Processing (FHPP) Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-20
The possibility of using a special type of Friction Stir Welding (FSW) – Friction Hydro Pillar Processing (FHPP) to manufacture a joining between dissimilar materials (high-carbon ductile iron FE55006 and low-carbon steel SAE 8620) is studied. The macrostructure, microstructure, microhardness and residual stresses of the welded joint are determined. The efficiency of using the FHPP technology for obtaining
-
Orientation Relationships and Changes in the Composition of S2 Titanium Silicides in Titanium Pseudo-β-Alloy VT47 Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-20 A. V. Zavodov, A. A. Shiryaev, N. A. Nochovnaya
-
Structure and Phase Composition of Heat Treated Al – Zr Bimetal Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-20 Yu. Yu. Emurlaeva, M. N. Khomyakov, N. S. Aleksandrova, K. I. Emurlaev, I. A. Bataev
-
Effect of the Temperature and Rate Parameters of Hot Deformation on the Mechanical Behavior of Forged Titanium Alloy VT14 Under Compression and Tension Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-20 A. G. Illarionov, F. V. Vodolazskii, Ya. I. Kosmatskii, E. A. Gornostaeva
-
Formation of Structure and Properties of Low-Carbon Bainite in Steel 08KhFA Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-19 M. A. Vyboishchik, I. V. Gruzkov, E. A. Chistopol’tseva, T. V. Tetyueva
-
Evolution of Gradient Structure Under Heat Treatment of Metastable Austenitic Stainless Steel Subjected to Cold Radial Forging Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-18 D. O. Panov, E. A. Kudryavtsev, A. V. Naumov, A. S. Pertsev, Yu. N. Simonov, G. A. Salishchev
-
Effect of Heat Treatment on Microstructure and Hardness of a High-Chromium Cast Iron Roll Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-18 Bo-Han Zhang, Hao-Nan Li, Jie-Bing Liu, Gui-Ying Qiao, Fu-Ren Xiao
-
Analysis of the Kinetics of Isothermal Bainitic Transformation in Alloy Steels Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-16
Isothermal bainitic transformation is studied in commercial and experimental alloy steels of various compositions using dilatometry. The effect of the conditions of cooling to the temperature of isothermal quenching on the subsequent kinetics of the bainitic transformation is considered. The experimental kinetics of formation of bainite is described with the help of the Austin–Rickett (AR) equation
-
Effect of Heat Treatment on Fatigue Strength and Frequency Stability of Tool Steel 6KhS Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-15
The effect of heat treatment on the fatigue processes developing in tool steel 6KhS loaded by a “soft” scheme of cantilever bending of flat specimens is studied. The fatigue limit and the cyclic endurance are determined. The frequency characteristics and the dynamics of the frequency stability in tests of steel specimens at a load close to the fatigue limit are presented. The fatigue resistance of
-
Influence of Gas Mixture Ratio on Wear and Corrosion Properties of Oxynitrided Films for 316L (03Kh17N14M3) Austenitic Stainless Steel Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-15 M. Aslan Çakir
-
Effect of Controlled Thermomechanical Processing Routes on the Structural and Textural States of Low-Carbon Low-Alloy Steel Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-15
The method of orientation microscopy (EBSD) is used to study the structural and textural states of samples of low-carbon low-alloy steel of type 06G2MB subjected to thermomechanical controlled processing (TMCP) by five pilot routes differing in the finishing hot-rolling temperature and in the intensity of the controlled cooling. The interrelation between the processing parameters, the structure and
-
Size Scatter of Disperse Particles: Influence on Grain Growth Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-15 V. Yu. Novikov
-
Effect of Heat Treatment on the Phase Composition of Copper-Zinc Coating on Steels Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-15 V. E. Arkhipov, T. I. Murav’eva, G. V. Moskvitin, M. S. Pugachev, O. O. Shcherbakova
-
Analysis of the Anomalous Effect of Heat Treatment on the Structure and Phase Transformations in High-Chromium Tool Steel Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-15
The effect of various heat treatments with heating to 1030 – 1250°C on the structure and microhardness of high-chromium tool steel 160Kh12MF is studied. The chemical composition is determined, the microhardness is measured, and the microstructure of the steel is analyzed after quenching, normalizing and annealing. It is shown that the customary heat treatments (quenching from the austenitic range for
-
Binary Phase Diagrams in the Science of Metals Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-14 Yu.I. Ustinovshikov
-
Structural States of Steel 316L in the Zone of Welded Joint Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-12-14
The structure of a welded joint of stainless steel 316L is studied by the methods of scanning electron microscopy including microprobe x-ray spectrum analysis and diffraction of backscattered electrons (EBSD). It is shown that a double-phase structure forms in the region of the weld including high-temperature δ-ferrite and austenite. The austenite and the ferrite undergo recrystallization in direction
-
Mathematical Modeling of the Argon Arc Welding Process. Part 1. Thermomechanical Approach and Model Justification Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-15 S. Yu. Kondrat’ev, A. V. Slyusarenko, Yu. A. Sokolov, M. D. Fuks
-
Role of Metallic Alloy Interatomic Chemical Reactions with Structure Formation during Heat Treatment Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-14 Yu. I. Ustinovshchikov
-
Microstructure and Wear Resistance of Nitride Layers on Armco-Iron Obtained By Nitriding with Zero Gas Flow Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-15 M. Keddam, M. Kulka, N. Makuch, K. Ostrovska, L. Maldzinski
-
Mathematical Modeling of the Argon Arc Welding Process. Part 2. Welding of HP40NbTi Alloy Pipelines Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-13 S. Yu. Kondrat’ev, A. V. Slyusarenko, Yu. A. Sokolov, M. D. Fuks
-
Experimental Study of Slurry Erosion of Ni-Hard Cast Iron and Prediction of Wear of Materials with the Use of Artificial Neural Network (ANN) Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-14 M. D. Makwana, B. M. Sutaria
-
Flow Stress Behavior and Governing Equation of Plastic Flow of Low-Carbon Steel at Elevated Temperatures Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-10 Z. Y. Wang, M. X. Ma, S. Zhong, S. Zhang, J. Feng, H. L. Wu, Yu. Cao
-
Mechanical Properties of Composite Materials Based on Fe – 18% Cr – 10% Ni Alloy Obtained Using Laser Heat Treatment Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-11 E. N. Blinova, V. D. Voronov, A. M. Glezer, E. D. Ishkinyaev, M. A. Libman, A. V. Osintsev, V. N. Petrovskii, N. A. Shurygina
-
Distribution of Alloying Elements in Multi-Pass Welded Joints of Chromium-Nickel Steel Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-09 R. A. Mamadaliev, P. V. Bakhmatov
-
Effect of Finish Rolling Temperature on the Texture and Fracture Resistance of Low-Carbon High-Strength Pipe Steels during Thermomechanical Treatment Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-08 D. A. Pumpyanskii, I. Yu. Pyshmintsev, M. L. Lobanov, S. G. Chikalov, N. V. Urtsev, S. V. Denisov, V. N. Urtsev
-
Effect of Heat Treatment on Two-Phase Ti – 22Al – 25Nb Alloy Phase Composition and Microhardness Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-09 Ling Shao, Yingwei Chen, Amit Datye, Sujun Wu, Tianle Wang, Zhibiao Tu, Jitang Zhang, Jinfang Wang, Na Xue, Weiwei Li, Cheng Dai, Liu Zu
-
Arrangement of Atoms of Interstitial Impurity in the Crystal Lattice of Iron Austenite and Mechanism of their Diffusion Jump Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-07 M. Yu. Semenov, V. S. Kraposhin, V. Arestov, V. A. Pancho-Ramirez, A. L. Talis
-
Increasing the Conductivity of Sintered Powder Al – Cu Material Due to Electroplating of Aluminium Particles with Copper Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-08 N. G. Puteri, Y. W. Yu, W. H. Lee
-
Wear Resistance of Aluminum Alloy A356 After Thorough Anodic Oxidation Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-08 Aziz Bariş Başyipit, Zeki Azakli, Recep Gümrük, Osman Bican
-
Special Features of Structural and Phase Transformations in Bainitic Steel Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-06 A. V. Malinin, V. D. Sitdikov, A. A. Kurilov
-
Formation of Composite Material by Magnetic Pulse Welding of Crystalline Titanium and Nickel-Based Amorphous Alloy Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-06 D. V. Lazurenko, A. A. Ivannikov, A. G. Anisimov, N. S. Popov, G. D. Dovzhenko
-
Synthesis of 25Kh15K Permanent Magnets and Study of Their Properties in Service in Magnetic and Thermal Fields Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-07 A. S. Zhukov, V. V. Bobyr’, I. V. Shakirov, A. V. Olisov, B. K. Barakhtin, V. A. Sein
-
Effect of Pulsed Current Duty Factor on Deformation Behavior of Aluminum Bronze Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-07 M. A. Pakhomov, G. G. Savenkov, M. A. Smakovsky, V. V. Stolyarov
-
Nitriding of Steel AISI D2 After Deep Cryogenic Treatment Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-11-07 F. D. Ramos, M. F. C. Moscoso, A. Regul, I. L. Diehl, C. A. T. S. Diehl
-
Surface Plastic Deformation of Spring Materials: Special Features of Structure and Properties Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-09-04 V. R. Baraz, E. A. Ishina
-
Effect of Thermocycling Treatment on Physicomechanical Properties of Low-Carbon Martensitic Steel 15Kh2G2NMFB for Parts of Precision Devices Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-09-04 I. M. Russkikh, A. A. Shatsov
-
Creep Rate of Pressings from High-Strength Aluminum Alloy 1960 (V96ts) Met. Sci. Heat Treat. (IF 0.6) Pub Date : 2023-09-04 T. A. Shlyapnikova, M. S. Oglodkov, N. E. Blinova, A. F. Dorzhiev